CNSPEED AN10 Oil Drain Flange

Contents

Turbo Oil Drain Flange AN10 User Manual

Brand: CNSPEED | Model: AN10 Oil Drain Flange

1. Introduction

This manual provides essential information for the installation and maintenance of your CNSPEED AN10 Turbo Oil Drain Flange. This component is designed to facilitate efficient oil return from your turbocharger, ensuring optimal performance and preventing oil leakage.

The flange is constructed from durable aluminum alloy, engineered to resist deformation and provide a fixed, leak-free seal. Its design aims for high oil output rates after proper installation.

2. Specifications

Feature Detail
Material Aluminum alloy
Item Weight 0.04kg
Special Features Fixed seal, no oil leakage, durable, not easily deformed, prevents corrosion, heat and pressure resistant.
OEM NO. YC101997
Origin Mainland China

2.1 Compatibility

  • Mitsubishi TD04, TD05, TD06 Series Turbo
  • IHI RHF4, RHB4, RHB5 Series Turbo
  • KKK K03, K04 Series (e.g., K0422-581, K0422-582)
  • All Turbos and Engines with 38 mm distance oil drain and 6mm bolts.

2.2 Dimensions

Refer to the diagram below for detailed measurements:

Dimensional drawing of the AN10 oil drain flange with measurements
Figure 1: AN10 Oil Drain Flange Dimensions. Key measurements include 22mm (0.86"), 12mm (0.47"), 6mm (0.23"), 8mm (0.31"), 39mm (1.53"), and 53mm (2.08").
  • Bolt Hole Distance: 38mm
  • Overall Length: 53mm (2.08")
  • Flange Width: 39mm (1.53")
  • AN10 Fitting Height: 22mm (0.86")
  • AN10 Fitting Diameter: 12mm (0.47")
  • Flange Thickness: 8mm (0.31")
  • O-ring Groove Depth: 6mm (0.23")

3. Kit Contents

The package includes the following items:

  • 1 x AN10 Oil Drain Flange (38mm bolt distance)
  • 1 x O-ring
  • 2 x 6mm bolts with washers (M6*1.0)
AN10 oil drain flange with two bolts
Figure 2: AN10 Oil Drain Flange and included bolts.

4. Setup and Installation

IMPORTANT: Professional installation is highly recommended. No detailed instructions are included with the product. Basic household tools are generally sufficient for installation, but specialized tools may be required depending on your specific turbocharger setup.

4.1 General Installation Steps

  1. Ensure the turbocharger's oil drain port is clean and free of debris.
  2. Place the O-ring into the groove on the AN10 oil drain flange.
  3. Align the flange with the oil drain port on your turbocharger.
  4. Insert the provided 6mm bolts through the flange and into the turbocharger's mounting holes.
  5. Tighten the bolts evenly to secure the flange, ensuring a snug fit without overtightening.
  6. Connect your AN10 oil return line to the flange.
  7. Verify that all connections are secure and there are no leaks.

4.2 Visual Aids and Examples

Video 1: Demonstration of turbo oil drain components, including the flange, fittings, and hose, with a test fit on a turbocharger. This video illustrates the general process of connecting the flange and AN fittings.
Installation example of the flange on a turbocharger
Figure 3: Example of the AN10 oil drain flange installed on a turbocharger.
Flange installed on a turbocharger, connected to a red AN fitting
Figure 4: The AN10 oil drain flange connected to an AN fitting and hose on a turbocharger.
Flange installed on a turbocharger, connected to a black AN fitting
Figure 5: Another view of the AN10 oil drain flange connected to an AN fitting and hose on a turbocharger.

5. Operating Instructions

Once installed, the AN10 Turbo Oil Drain Flange operates passively to facilitate the return of oil from the turbocharger to the engine's oil pan. Ensure that the oil return line connected to the flange has a clear, unobstructed path and sufficient diameter to prevent oil backup, which can lead to turbo seal failure.

The flange is designed to protect the turbo from high-pressure oil feed by ensuring efficient drainage.

6. Maintenance

  • Regularly inspect the flange and connected oil return line for any signs of oil leaks, cracks, or damage.
  • Check the tightness of the mounting bolts periodically, especially after initial installation and during routine vehicle maintenance.
  • Ensure the O-ring remains in good condition. Replace if any signs of wear or degradation are observed to maintain a proper seal.
  • Keep the area around the oil drain flange clean to easily spot any potential leaks.

7. Troubleshooting

7.1 Oil Leaks

  • Cause: Improperly tightened bolts, damaged O-ring, or incorrect flange alignment.
  • Solution: Re-tighten bolts evenly. Inspect and replace the O-ring if necessary. Ensure the flange is correctly seated against the turbocharger's drain port.

7.2 Bolt Compatibility

  • Issue: Included bolts (M6) do not fit the turbocharger's mounting holes (e.g., M8).
  • Solution: Verify the bolt size required by your specific turbocharger model before installation. If the provided M6 bolts are incompatible, you will need to source appropriate bolts (e.g., M8) separately. Do not attempt to force incorrect bolt sizes or modify the flange or turbocharger without professional guidance.

8. User Tips

  • Always double-check the bolt size required for your turbocharger's oil drain port. While M6 bolts are included, some turbo models may require M8 bolts, necessitating separate purchase.
  • Ensure the O-ring is properly seated and free from pinches or damage during installation to guarantee a leak-free seal.
  • Consider using a small amount of thread sealant on the AN fitting threads (if applicable) to further prevent leaks, though the O-ring on the flange itself is the primary seal.

9. Warranty and Support

For specific warranty information, please refer to the seller's terms and conditions at the time of purchase. General support for product inquiries can be directed to the seller.

A detailed user manual in PDF format is available for download: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.