SZRZGT 10W

Contents

SZRZGT 10W High Power LED Chip Instruction Manual

Model: 10W | Brand: SZRZGT

Introduction

This manual provides essential information for the safe and effective use of your SZRZGT 10W High Power LED Chip. It covers specifications, installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of the product.

Assortment of 10W LED chips in various colors

Figure 1: Various 10W LED Chip types and colors.

Specifications

Attribute Value
Model TypeHigh Power Integrated Chip
Product NameIntegrated LED Beads
Brand NameSZRZGT
Model Number10W
Power10W
ShapesTetragonum
Integrated Way3 Series 3 Paralleling
Forward Voltage9-12V
Current1000mA
Luminous Flux90-120LM/W
Color-Rendering Index60-85
Beam Angle170 degrees
Working Temperature-20°C to 60°C
Life Span80,000 Hours
CertificationROHS
OriginMainland China

Detailed Color Specifications (10W 3x3)

Color Temp / Wave Forward Current Forward Voltage Luminous Flux LED Chips
Warm White3000-3500K900-1050mA9.6-10.2V800-900LM30*30mil
Natural White4000-5500K900-1050mA9.6-10.2V800-900LM30*30mil
White6000-6500K900-1050mA9.6-10.2V800-900LM30*30mil
Cool White8000-10000K900-1050mA9.6-10.2V800-900LM30*30mil
Red620-630nm900-1050mA6.6-7.2V450-550LM30*30mil
Green520-530nm900-1050mA9.2-10.2V630-720LM30*30mil
Blue450-460nm900-1050mA9.2-10.2V200-300LM30*30mil
Yellow2000-2200K900-1050mA9.6-10.2V400-450LM30*30mil
Deep Red 660nm660nm900-1050mA6.6-7.2V450-550LM30*30mil
Royal Blue 440nm440nm900-1050mA9.6-10.2V300-400LM30*30mil
440nm and 660nm440/660nm900-1050mA7.6-8.2V420-600LM30*30mil
Full Spectrum380-850nm900-1050mA9.2-10.2V200-300LM30*30mil
UVA 365nm360-365nm900-1050mA9.2-10.2V---45*45mil
UVA 395nm390-395nm900-1050mA9.2-10.2V90-135LM45*45mil
RGBR:620-630nmR:300-350mAR:6.6-7.2VR:90-100LMR:30*30mil
G:520-530nmG:300-350mAG:9.6-10.2VG:120-130LMG:30*30mil
B:460-470nmB:300-350mAB:9.6-10.2VB:30-40LMB:30*30mil
Diagram showing the dimensions of the 10W LED chip

Figure 2: 10W LED Chip dimensions. All dimensions are in millimeters. Tolerance is ±0.1mm unless otherwise noted.

Chart showing various normal light and grow light LED spectrums and colors

Figure 3: Overview of available Normal Light and Grow Light LED spectrums.

Safety Information

WARNING!

  • Not suitable for children under 3 years old.
  • Do not look directly at the product with your eyes when it is illuminated.
  • Pay attention to the heat dissipation of the product to prevent overheating.
  • Ensure proper electronic security protection during installation and operation.
CE UK CA RoHS compliance logos

Product complies with CE, UK CA, and RoHS standards.

Setup and Installation

1. LED Welding Instructions

  • Immersion Welding: Control welding temperature at 230°C ± 5°C. Maximum immersion time is 5-10 seconds. The immersion welding position should be at least 3 millimeters away from the colloid.
  • Soldering Iron: Use a constant temperature soldering iron for manual soldering. The maximum temperature for a single contact of the solder pad is 350°C for 3-5 seconds.
  • Grounding: Ensure proper grounding. Static electricity must not exceed the safe range. The welding position should be at least 3 degrees away from the adhesive.

2. LED Heat Dissipation Notice

Proper heat dissipation is crucial for the longevity and performance of the LED chip. Use an aluminum profile or copper radiator.

  • For integrated LED chips above 20W, it is recommended to add a fan for active heat dissipation.
  • Ensure the temperature of the light bulb does not exceed 50°C.
  • For 1W LED beads, use heat sinks with a surface area greater than 50 square centimeters.
  • For 3W LED beads, use heat sinks with a surface area of 150 square centimeters.
  • The lamp beads must be tightly attached to a flat heat sink.
  • Thermal Conductive Silicone Grease: Apply a thin layer to fill the gap between the bottom of the lamp bead and the heat sink. Avoid applying too much, as excessive grease can hinder heat dispersion.

3. Pin Forming Instructions

  • The bracket must be at least 2 millimeters away from the gel before it can be bent.
  • The bracket must be formed using fixtures and completed by professionals.
  • The bracket forming must be completed before welding.
  • The bracket forming must ensure that the pins and spacing are consistent with those on the circuit board.

Video 1: Demonstration of various LED chip colors and their illumination.

Operating Instructions

Once properly installed and connected to a suitable power supply (within the 9-12V forward voltage range and 1000mA current), the LED chip will illuminate. Ensure correct polarity when connecting to avoid damage.

  • Connect the positive (+) terminal of the power supply to the anode of the LED chip and the negative (-) terminal to the cathode.
  • Verify that the power supply provides the correct voltage and current as specified in the specifications section.
  • Always ensure adequate heat dissipation during operation to maintain the LED chip's temperature below 50°C.
Close-up of an LED chip emitting purple light

Figure 4: An LED chip emitting purple light during testing.

Maintenance

The SZRZGT 10W High Power LED Chip requires minimal maintenance. Follow these guidelines to ensure its longevity:

  • Keep the LED chip and its heat sink clean and free from dust and debris to ensure efficient heat dissipation.
  • Avoid physical shock or excessive pressure on the LED chip.
  • Regularly check connections for any signs of wear or corrosion.
  • Ensure the operating environment remains within the specified temperature range (-20°C to 60°C).

Troubleshooting

If you encounter issues with your LED chip, refer to the following common problems and solutions:

  • LED not lighting up:
    • Check the power supply: Ensure it is providing the correct voltage (9-12V) and current (1000mA).
    • Verify polarity: Ensure the positive (+) and negative (-) connections are correct.
    • Inspect connections: Check for loose or faulty wiring.
  • LED flickering or dimming:
    • Check power supply stability: An unstable power supply can cause flickering.
    • Inspect connections: Ensure all connections are secure and free from corrosion.
    • Verify heat dissipation: Overheating can lead to reduced performance and flickering. Ensure the heat sink is adequate and properly attached.
  • LED overheating:
    • Ensure adequate heat sink: Refer to the heat dissipation guidelines in the Setup section.
    • Check thermal paste application: Ensure a thin, even layer of thermal conductive silicone grease is applied.
    • Improve ventilation: Ensure sufficient airflow around the LED and heat sink.

User Tips

  • Application-Specific Spectrum: When using these LED chips for specialized applications like marine aquariums or plant growth, carefully consider the specific wavelength requirements. Different LED colors and spectrums are optimized for various biological processes.
  • Heat Management is Key: Always prioritize robust heat dissipation. Even with proper installation, insufficient cooling can drastically reduce the lifespan and efficiency of high-power LED chips.
  • Quantity for Projects: Be mindful of the quantity needed for your project. These chips are typically sold individually, so plan accordingly for larger installations.

Warranty and Support

For detailed warranty information or technical support, please refer to the official user manual PDF or contact the seller directly. The user manual (PDF) can be accessed via the following link: User Manual (PDF).

For any product-related inquiries or assistance, please reach out to the LED World company store.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.