VaneAims Metal Key Knob Switch

Contents

VaneAims Metal Key Knob Switch User Manual

Models: 19MM and 22MM Key Knob Switches

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your VaneAims 19MM and 22MM Metal Key Knob Switches. These waterproof switches feature an integrated LED light and are available in 2-position or 3-position latching configurations with 1NO1NC or 2NO2NC contacts.

Four VaneAims Metal Key Knob Switches with keys
VaneAims Metal Key Knob Switches with included keys.
Four VaneAims Metal Key Knob Switches with illuminated LED rings in red, yellow, blue, and green
Switches featuring illuminated LED rings in various colors.

2. Setup and Installation

2.1. Safety Precautions

WARNING: Disconnect the power supply completely before beginning any installation or removal procedures to prevent electric shock.

2.2. Installation Steps

  1. **Power Off**: Ensure the power supply is completely turned off before installation or removal.
  2. **Mounting**: Insert the switch into the pre-drilled panel cutout.
  3. **Secure**: Fasten the switch securely with the provided nut from the back of the panel.
  4. **Wiring**: Connect the load and power supply according to the appropriate wiring diagram below.

2.3. Wiring Diagrams

Connect the load and power supply as shown in the diagrams. The switches are available with 1NO1NC (1 Normally Open, 1 Normally Closed) or 2NO2NC (2 Normally Open, 2 Normally Closed) contact configurations.

Wiring Diagram showing two plans for connecting the key switch
Wiring Diagram:
  • Plan A: Press the switch, the LED light is on, and the load is on. This configuration connects the power to the common (C) terminal, the normally open (NO) terminal to the device, and the LED is wired in parallel with the load.
  • Plan B: When powered on, the LED stays lit, and the switch connects to the normally open (NO) contact. This configuration connects the power to the common (C) terminal, the normally open (NO) terminal to the device, and the LED is wired in parallel with the power source.
Rear view of VaneAims Key Knob Switches showing terminals
Rear view of the key knob switches, illustrating the terminal connections.

3. Operating Instructions

The VaneAims Metal Key Knob Switches are designed for reliable control with a latching mechanism.

3.1. Switch Positions

  • 2-Position Switch: This type typically functions as a simple ON/OFF control. Turning the key from one position to the other will switch the circuit from OFF to ON, or vice-versa. The order of operation is generally OFF → ON.
  • 3-Position Switch: This type allows for selection between two different circuits or states, with a central OFF position. The order of operation is typically ON → OFF ← ON (left selection, center off, right selection).

3.2. Latching Function

The switch features a latching mechanism. Once the key is turned to a position, it will remain in that position until manually turned back. The key can be removed from the switch at any position, providing security and flexibility.

3.3. LED Light Operation

The integrated LED light indicates the status of the switch or circuit, depending on how it is wired (refer to Section 2.3 Wiring Diagrams for details).

4. Maintenance

  • **Cleaning**: Keep the switch surface clean and free from dust and debris. Use a soft, dry cloth for cleaning. Avoid abrasive cleaners or solvents.
  • **Inspection**: Periodically check the wiring connections to ensure they are secure.
  • **Environmental**: Ensure the switch operates within the specified working temperature (-25℃ to +55℃) and humidity (45-85%RH) ranges. Avoid environments with freezing conditions or excessive condensation.

5. Troubleshooting

  • **Switch Not Responding**: Check all wiring connections for proper contact. Ensure the power supply is active and correctly connected according to the wiring diagram.
  • **LED Not Lighting Up**: Verify the LED voltage matches the power supply. Check LED wiring for correct polarity and secure connections.
  • **Intermittent Operation**: Inspect for loose connections or damage to the switch terminals.

6. Specifications

General Product Specifications
Feature Description
Brand NameVaneAims
Item TypeSWITCHES
Switch TypeKey Knob Switch (Latching)
Mounting Diameter19mm / 22mm (also 16mm for some models)
Position2 or 3 position
Switch Combination1NO1NC or 2NO2NC
Housing MaterialBrass chrome plating / Stainless steel
Base MaterialPBT
FeaturesWaterproof, LED Light, Latching
Is Smart DeviceNo
OriginMainland China
CertificationCE (EN61058-1:2002+A2:2008, EN60947-1:2004)
Electrical and Performance Characteristics
Characteristic Value
Maximum Current (Ith)5A
Rated Insulation Voltage (Ui)250V
LED Voltage Options3-6V, 12-24V, 220V (AC/DC 6V, 12V, 24V, 36V, 110V, 220V customizable)
Rated LED Current5-48V 15mA; 110-250V ~2mA
Working Temperature-25℃ to +55℃ (no freezing, air must circulate)
Working Humidity45-85%RH (no condensation)
Contact Resistance< 50mΩ
Insulation Strength≥ 1000MΩ
Highest Withstand Voltage1500V, AC50HZ, 1 Minute
Vibration Resistance50HZ, Amplitude about 1.2mm
Impact ResistanceBigger than 10g
Solder Heat Resistance320℃ for no more than 2 seconds
Protection GradeIP65, IK02
Electrical Life> 50,000,000 times
Mechanical Life (Selector)500,000 times
Mechanical Life (Key Switch)200,000 times
Nut TorqueAbout 0.8Nm
LED Life40,000 hours (reference value)

6.1. Product Dimensions

Dimension diagram for 19mm 2-position key switch
Dimensions for 19mm 2-position key switch (Mounting Hole Size: 19mm).
Dimension diagram for 22mm 3-position key switch
Dimensions for 22mm 3-position key switch (Mounting Hole Size: 22mm).

7. User Tips

  • The key can be removed from the key switch at any position, offering flexibility in operation.
  • Some users have noted that the keys may produce a slight noise when turning. This is generally a normal characteristic and does not affect functionality.
  • The design of the key switch base may prevent it from being fully inserted into some sockets, but this typically does not impact its functionality.

8. Warranty and Support

For any product-related inquiries, technical support, or issues, please contact the seller directly. Ensure you have your purchase details ready when contacting support.

Contact Information:

  • Email: chenmaike3303@sina.com
  • Mobile/WhatsApp/WeChat/Skype: +86 15058777695
  • Address: Yueqing, Zhejiang, China

9. Frequently Asked Questions (FAQ)

Q: Is a wired socket or connector included with the switch?
A: The switch sold via this link does not include a plug-in connector or wired socket. These may need to be purchased separately. Please contact the seller for more information on purchasing compatible connectors.
Q: Can additional spare keys be purchased?
A: Please contact the seller directly to inquire about purchasing additional spare keys.
Q: What should I do if I encounter quality issues with the product?
A: If you experience any quality issues, please contact the seller immediately. They are committed to ensuring customer satisfaction and will work to resolve any problems.
Q: Can the product be customized?
A: Customization options, such as stainless steel housing material or specific voltage grades, may be available. Please contact the seller to discuss your specific requirements.

© 2023 VaneAims. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.