1. Introduction
Thank you for purchasing the RIDEN RD6018 / RD6018W Constant Voltage Constant Current DC Power Supply. This manual provides detailed instructions for setup, operation, and maintenance to ensure a better experience and prevent misuse. Please read it carefully and keep it for future reference.
Note: This instruction manual corresponds to firmware versions such as RD6018(V1.39) and RD6018W(V1.43). Page layouts and operations may vary slightly with different firmware versions. We recommend downloading the latest firmware for the best experience.
Video: Overview of the RIDEN RD6018 DC Power Supply features and functions.
2. Safety Information
Important Safety Warnings:
- Only connect cables if you have a foundation in electronic and electrical engineering.
- Ensure the device is reliably grounded to prevent electric shock.
- Do not install or remove the Wi-Fi module when the device is powered on, as this may cause damage.
- When charging batteries, ensure you know the battery parameters well. Using incorrect charging methods carries a risk of fire and explosion.
- If using an AC-DC converter or transformer, you must add a rectifier and filter. The DC output voltage without load should be lower than 65V. Power grid voltage fluctuations can cause high output voltage and damage the device.
- Avoid using electric bike chargers, second-hand power supplies, or modified power supplies, as they are often unstable and can output high voltages, damaging your load.
- If connecting an inductive load (e.g., a motor), the maximum working current should not exceed 1/3 of the full range.
For detailed safety information, please refer to the full user manual PDF: User manual (PDF)
3. Package and Accessory List
The product is packaged in a carton. Upon opening, you will find the instruction card. The accessories typically include:
- RD power supply unit (RD6018 or RD6018W)
- External temperature sensor cable (10K B3950)
- Backup fuse (1 piece)
- U-shaped plug (for output line connection)
- For RD6018W models: WiFi communication board (pre-installed or included separately)
- For S800 case option: S800 case, internal cables, and screws (power supply not included)
Note: The WiFi/RS485 board is ordered separately if not included in your chosen model.





4. Specifications
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Model | RD6018 / RD6018-W | Input voltage range | 6-70.00V |
| Output voltage range | 0-60.00V | Output current range | 0-18.00A |
| Output power range | 0-1080W | Input voltage measurement resolution | 0.01V |
| Output voltage setting measurement resolution | 0.01V | Output current setting measurement resolution | 0.01A |
| Battery voltage measurement resolution | 0.01V | Input voltage measurement accuracy | ±(1%+5 digits) |
| Output voltage accuracy (setting and measurement) | ±(0.3%+3 digits) | Output current accuracy (setting and measurement) | ±(0.5%+5 digits) |
| Battery voltage measurement accuracy | ±(0.5%+3 digits) | Automatic cut off current value (charging) | 100mA |
| Output ripple typical (VPP) | 250mV@6A | Working temperature range | -10℃~40℃ |
| External sensor Temperature detection range | -10℃~100℃/0℉~200℉ | External sensor Temperature detection accuracy | ±3℃/±6℉ |
| Constant voltage mode response time | 2ms (0.1A-5A load) | Constant voltage mode load regulation | ±(0.1%+2 digits) |
| Constant current mode load regulation | ±(0.1%+3 digits) | Capacity measurement range | 0-9999.99Ah |
| Energy measurement range | 0-9999.99Wh | Capacity and energy statistical error | ±2% |
| Buck working mode | Voltage drop >1V and >10% | Over temperature protection | System temperature >80℃ |
| Screen brightness setting | 0-5 (6 levels in total) | Screen | 2.4 inch color HD display |
| Weight (with package) | About 0.68kg | Product dimension | 167*81*69mm |
| Cooling fan start condition | Output current >8A or System temperature >45℃ | Cooling fan shut down condition | Output current <7.9A and System temperature <45℃ |
| Input/output fuse | 1808 fast blow fuse | Fuse current | 10A (RD6006/P), 20A (RD6012/P), 25A (RD6018), 30A (RD6024), 40A (RD6030) |
| Input terminal | HT508K-2P / HT508K-4P / K14 Terminal | Support USB communication | Yes |
| Support WiFi communication | Only W version support WiFi communication | Work mode | buck mode |
5. Setup
5.1. Case Assembly (S800 Case)
The S800 case is designed for DIY assembly with the RD6018/RD6018W unit and a compatible AC-DC switching power supply (e.g., 800W/1000W). The case includes internal cables and screws for assembly. Please refer to the assembly instruction video for detailed steps:
- RD6018 and S800 case assembly instruction: Assembly Video

5.2. Power Supply Connection
The RD6018/RD6018W unit requires a DC input. If you are using an AC input, you must use a switching power supply. Ensure the power supply is grounded to avoid leakage risk.
- Recommended PSU: Use a custom PSU or a reputable brand PSU.
- Not Recommended PSU: Avoid AC-DC converters or transformers without proper rectification and filtering. DC output voltage without load should be below 65V.
- Banned PSU: Do not use electric bike chargers, second-hand power supplies, or modified power supplies, as they are unstable and can damage your load.

5.3. Connecting External Components
- External Temperature Sensor: Plug the external temperature sensor cable into the 'S' external temperature sensor interface.
- WiFi Communication Board (RD6018W only): Insert the WiFi communication board into the 'U:U:U' Communication module interface.
- Clock Battery: A CR1220 battery (not included) is required for the clock function.

6. Operation
6.1. Front Panel Overview

The front panel features a digital keypad, encoder potentiometer, and a 2.4-inch color HD display for clear data viewing.
- A: Power button
- B: SHIFT button: Activates second functions.
- C: Quick storage button
- D: Current/Over current protection setting
- E: Voltage/Over voltage protection setting
- F: Micro USB port
- G: Power supply output negative terminal / Battery charging negative terminal
- H: Battery charging positive terminal: Dedicated for battery charging.
- I: Power supply output positive terminal: Connect 4mm banana plug.
- J: Output ON/OFF switch
- K: Enter/Confirm button
- L: Encoder potentiometer: Rotate to adjust values, press to cancel/return.
- M: Direction button
- N: Keypad
- O: Screen
6.2. Basic Operation
After power-on, the device displays a boot image and then enters the main page.
- Setting Output Voltage and Current: Use the
I-SETandV-SETbuttons, then rotate the encoder potentiometer to adjust values. You can also use the keypad (N) to enter values directly. - Data Storage and Recall: Press
MEM+ keypad button 1-9 to store current settings. PressSHIFT+ keypad button 1-9 to quickly recall saved data. - Keypad Lock/Unlock: Press
SHIFT+LOCKto lock or unlock the keypad. The keypad automatically locks during communication. - Display Style Selection: On the main page, press the direction button to cycle through Traditional, Detail, and Curve display styles.


6.3. Battery Charging Function
Connect the green terminal (H: Battery charging positive terminal) to the battery's positive electrode and the black terminal (G: Battery charging negative terminal) to the battery's negative electrode. Once connected, the AG: battery charging indicator will turn red. Press ON/OFF to start charging. The AG indicator will turn green when charging.
The output will automatically cut off if the actual output current is lower than the set cut-off current value (default 10mA) or if the external temperature sensor detects a temperature greater than the cut-off temperature value.
Warning: It is strongly recommended to use the original charger for your battery. The charging function of this device is for temporary replacement only, not long-term use. Incorrect battery parameters or charging methods can lead to fire and explosion.
Battery charging operation video: Battery Charging Video
6.4. System Settings
Press SHIFT + 0 to enter the system setting menu. Use the direction buttons and encoder potentiometer to navigate and adjust settings.
- Language: Set to English by default. Options include Simplified Chinese, French, German, and Russian.
- Take OK: When ON, a prompt appears when recalling data groups. When OFF, settings are applied directly.
- Take Out: When ON, the previous output status is maintained when recalling data groups.
- Boot Power: When ON, the output automatically turns on after booting.
- Boot Logo: When ON, the boot logo is displayed first.
- Buzzer: Controls button press sound.
- Backlight: Adjustable from level 0-5.
- Update Rate: Sets the refresh rate for output voltage and current.
- Max Power: Set to 740W by default, adjustable from 0-740W.
- Temperature Unit: Switch between °C and °F.
- Cut-Off Current (Battery Charger Sub-menu): Default 10mA, editable.
- Cut-Off Temp (Battery Charger Sub-menu): Default 60°C.
- Communication Interface: Set to USB by default. Can be changed to WIFI/TTL/RS485.
- Address: Default 001, adjustable 001-255.
- Date and Time: Set year (2000-2100), month, day, hour, minute, second.
7. Software and Connectivity
7.1. Mobile Phone APP (Android & iOS)
The RD6018W model supports WiFi connection for APP control. The RD6018 (non-W version) only supports PC software via USB.
- Android APP: Supports Android 5.0 to Android 12.0. Download from the provided link or search "Ruideng" on Google Play.
- iOS APP: Supports iOS 10.0-16.1 (iPhone 6 and above). Search "RdPower" in the Apple App Store.
Important: Before purchasing, download and test the APP/PC software for compatibility with your device. Incompatibilities may occur with certain operating systems (e.g., Harmony OS). We do not provide refunds if the product functions correctly but the software does not work on your specific device.
Network Distribution (WiFi Connection):
- Insert the WiFi board (if not pre-installed) and power on the RD6018W. The blue LED should blink once.
- Set the communication interface to WIFI on the device and restart.
- Place the RD6018W and your mobile phone close to a 2.4G router. Ensure the phone is on the same 2.4G network, and the router has AP isolation and WMM functions disabled.
- On the APP, select "Add Device" and choose "RD power series".
- Enter your WiFi password and confirm the 2.4G network.
- Click "INITIALIZATION" and wait for connection.
Troubleshooting WiFi Connection: If connection fails, power off the module, re-operate, or try using your phone's hotspot. If using a Huawei phone, turn off the random MAC address function. If the phone's IP changes, reset the network on the RD6018W by pressing the direction button and then ENTER.

7.2. PC Software
Requirements: Windows 7-10 system with internet connection.
Installation:
- Download the PC software from the provided link.
- Unzip the files.
- Install the CH341SER driver.
- Install the .Net framework 4.7.2.exe environment.
- Connect the RD6018/RD6018W to your PC via a Micro USB cable.
- Run RidenPowerSupply.exe.
Note: The WiFi function for PC software is a test function and may have compatibility issues. If it doesn't work, use the USB connection.

7.3. Firmware Update & Customization
- Firmware Update: Connect the device to PC in boot mode (hold
ENTERand power on). Use the PC software to update. - Boot Logo Update: Use the PC software to upload a custom boot logo.
- Version Update Detection: The PC software can detect new firmware versions.
Firmware update video: Firmware Update Video

8. Maintenance
- Cleaning: Keep the device clean and free from dust.
- Fuse Replacement: A backup fuse is provided. If a fuse burns out due to incorrect operation, you can temporarily use the backup fuse (supports up to 10A). For full output, it is recommended to solder a new fuse in place of the damaged one.
- Clock Battery: Replace the CR1220 battery when the clock function is no longer powered.
9. Troubleshooting
9.1. Common Issues & Solutions
- Output automatically turns off / Alarm: If the input voltage exceeds 72V, the output will be turned off, and an alarm will be prompted.
- Over Temperature Protection (OTP): If the system temperature exceeds 80°C, the output will shut down automatically.
- Over Voltage Protection (OVP) / Over Current Protection (OCP): If the output voltage/current exceeds the set protection values, the output will shut down.
- Deformed Case: Minor deformation during shipping is possible. It can usually be adjusted by hand. If this is a concern, please consider before purchasing.
- Traces on Panel: Slight traces at button holes are normal due to the injection molding process and not considered damage.
9.2. Software & Connectivity Issues
- APP/PC Software Crashes: Due to potential incompatibilities with various operating systems, it is recommended to download and test the software before purchasing.
- WiFi Connection Failure (RD6018W):
- Ensure the WiFi board is properly inserted.
- Verify your WiFi network is 2.4GHz.
- Disable client isolation/AP isolation and WMM functions on your router.
- Ensure location and storage services are enabled for the APP.
- PC WiFi Connection Issues: The PC WiFi connection is a test function and may not be compatible with all computers. If it fails, use the USB connection.
10. User Tips
- Always ensure proper grounding for safety, especially when dealing with AC input via a switching power supply.
- For battery charging, always verify battery parameters to prevent damage or hazards.
- If you plan to use the device with inductive loads, remember to limit the working current to 1/3 of the full range.
- Keep your device's firmware updated for the best performance and access to new features.
- Familiarize yourself with the various protection settings (OVP, OCP, OTP) to safeguard your device and connected loads.
11. Warranty and Support
The manufacturer, Hangzhou Ruideng Technology Co., Ltd., holds the copyright for this instruction manual. Unauthorized use for commercial purposes is prohibited.
Damage resulting from incorrect operation, especially during calibration or using incompatible power supplies, may not be covered under warranty.
For further assistance, please contact RIDEN Official Store directly.
Contact Information:
- Email: 1749808860@qq.com
- WhatsApp: +8615868147353
- QQ Group: 550112838
- WeChat: 15868147353