1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your TEDELIGO S2202Ch RF 110V 220V Wireless Remote Control Switch. This 2-channel relay receiver, operating at 433MHz, is designed for versatile applications including controlling garage doors, AC motors, and various lighting fixtures. Please read this manual carefully before use to ensure proper and safe operation.

Figure 1: TEDELIGO S2202Ch Smart Switch and Remote Controls
2. Specifications
2.1. Receiver Technical Data
| Parameter | Value |
|---|---|
| Input Power | AC 85V-250V (50/60Hz) |
| Max Current | 10A (Resistive load) |
| Max Load | 2200W |
| RF Frequency | 433MHz |
| RF Working Mode | Superheterodyne |
| Receive Sensitivity | >97dbm |
| Decoding Mode | MCU software decoding |
| Remote Storage | ≤10pcs |
| Support Remote Type | 1527 Learning code (Rolling code can be designed) |
| Working Mode | Momentary, Toggle, Latching+stop |
| Size (L*W*H) | 85.3*43.6*30.2 mm |
| Learning Style | Learning Button |
| Working Temperature | -20°C to 80°C |
| Quiescent Current | <5mA |
| Output Port | L1 L2 N |
| Input Port | L N |
| Weight | ≈82g |
| Color | White |
2.2. Remote Control Technical Data
| Parameter | Value |
|---|---|
| RF Frequency | 433MHz |
| Support Encoding | 1527 Learning code |
| Transmitting Range | Up to 300m (theoretical distance in open space) |
| Battery | 1x 23A12V (Included) |
| Size | 90*40 mm |
| Remote Button | 3 buttons |

Figure 2: Receiver Dimensions and Features

Figure 3: Remote Control Dimensions and Features
3. Safety Warnings
- Always shut off power before installation or any operation. Ensure electricity is correct after testing.
- Promptly change the remote control battery when its voltage is insufficient (generally, get close transmitting).
- Avoid metal masks, large equipment, or strong interference electromagnetic fields when using wireless RF products.
- Avoid too short a distance between the remote control and receiver board.
- Avoid abnormal use of the product. Abnormal use will reduce product performance and life, and may damage the products or create danger.
4. Setup and Wiring
4.1. Wiring Diagrams
The receiver can be used to control lights or AC motors. Refer to the diagrams below for correct wiring.

Figure 4: Wiring for Lights and AC Motor Control
4.2. Learning/Pairing Modes
The receiver supports three working modes: Momentary, Toggle, and Latched. Follow the steps below to pair your remote control with the receiver in the desired mode.
4.2.1. Momentary Mode (Press and Hold)
- Press the learning button on the receiver 1 time. The LED indicator will flash once, then stay on, indicating it's in momentary setting mode.
- Press the 'UP' button on the remote control. The LED indicator on the receiver board will flash 3 times, then stay on.
- Press the 'DOWN' button on the remote control. The LED indicator on the receiver board will flash 3 times, then turn off. Pairing for Momentary Mode is successful.
4.2.2. Toggle Mode (Press On, Press Off)
- Press the learning button on the receiver 2 times. The LED indicator will flash twice, then stay on, indicating it's in toggle setting mode.
- Press the 'UP' button on the remote control. The LED indicator on the receiver board will flash 3 times, then stay on.
- Press the 'DOWN' button on the remote control. The LED indicator on the receiver board will flash 3 times, then turn off. Pairing for Toggle Mode is successful.
4.2.3. Latched Mode (Press On, Another Button Off)
- Press the learning button on the receiver 3 times. The LED indicator will flash three times, then stay on, indicating it's in latched setting mode.
- Press the 'UP' button on the remote control. The LED indicator on the receiver board will flash 3 times, then stay on.
- Press the 'DOWN' button on the remote control. The LED indicator on the receiver board will flash 3 times, then stay on.
- Press the 'Middle' (Stop) button on the remote control. The LED indicator on the receiver board will flash 3 times, then turn off. Pairing for Latched Mode is successful.
Video 1: Demonstration of wiring, pairing, and operating modes (Momentary, Toggle, Latched) for AC motors and LED lights.

Figure 5: Visual Guide for Pairing and Cleaning Data
4.3. Clear/Reset Function
To clear all paired remote controls from the receiver's memory:
- Press the learning button on the receiver 8 times.
- The receiver's LED will flash 5 times, indicating that all remote control data has been successfully cleared from its memory.
Note:
- After clearing, all previously paired remotes will no longer control the switch. You must re-pair them.
- If you wish to change the operating mode of a remote that has already been set, you must first perform the Clear/Reset function.
5. Operating Modes Explained
5.1. Momentary Mode
In Momentary Mode, the relay remains active only while the remote button is pressed. Releasing the button will immediately disconnect the relay.
- Press and hold the 'UP' button: The first relay (L1) will activate.
- Release the 'UP' button: The first relay (L1) will deactivate.
- Similarly, pressing and holding the 'DOWN' button will activate the second relay (L2), and releasing it will deactivate L2.
5.2. Toggle Mode
In Toggle Mode, each press of a remote button alternates the state of the corresponding relay (on/off).
- Press the 'UP' button once: The first relay (L1) will activate.
- Press the 'UP' button again: The first relay (L1) will deactivate.
- Similarly, pressing the 'DOWN' button once will activate the second relay (L2), and pressing it again will deactivate L2.
5.3. Latched Mode (with Stop)
Latched Mode is suitable for applications requiring sequential operation, such as motor forward/reverse with a stop function. Pressing one button activates a relay, and it stays active until another specific button is pressed.
- Press the 'UP' button: The first relay (L1) will activate and remain active.
- Press the 'DOWN' button: The first relay (L1) will deactivate, and the second relay (L2) will activate and remain active.
- Press the 'Middle' (Stop) button: Both relays (L1 and L2) will deactivate.
6. Product Application Area
The TEDELIGO S2202Ch Smart Switch is highly versatile and can be integrated into various environments:
- Residential: Control garage doors, electric gates, house doors, electric curtains, lamps, LED lights, and fans.
- Commercial/Industrial: Use in farms, factories, offices, laboratories, and supermarkets for controlling water pumps, ventilation devices, and signal transmission.
- Motor Control: Ideal for controlling the positive and negative rotation of AC motors, motor switches, and DIY projects.

Figure 6: Diverse Applications of the Smart Switch

Figure 7: Receiver with Fixed Holes for Easy Wall Mounting
7. Maintenance
- Keep the device clean and dry. Avoid exposure to moisture or extreme temperatures.
- Regularly check the remote control battery and replace it when necessary to ensure optimal performance.
- Ensure all wiring connections are secure and free from damage.
- Do not attempt to disassemble or repair the device yourself. Contact customer support for assistance.
8. Troubleshooting
8.1. Common Questions & Answers
- Q: Can I use my own remote to control this switch?
A: It is not recommended. Ensure your remote has the same frequency (433MHz), encoding (1527 learning code), and modulation (ASK) as this receiver for compatibility. - Q: Does this switch have Wi-Fi functionality?
A: No, this switch is RF (Radio Frequency) only and does not support Wi-Fi. - Q: Can I use it to control my fan?
A: Yes, you can use this switch to control a fan. - Q: Do I need to set up each remote individually?
A: Yes, each remote needs to be paired with the receiver one by one. The remotes do not have a clone function. You can set them up in different modes if desired. - Q: Does the remote come with batteries?
A: Yes, the remote control includes a 23A12V battery.
8.2. General Issues
- Device not responding: Check power supply to the receiver. Ensure the remote control battery is not depleted. Verify that the remote is paired correctly in the desired mode.
- Short range: Replace the remote control battery if it's low. Ensure there are no significant obstructions (metal, large equipment) or strong electromagnetic interference between the remote and receiver.
- Intermittent operation: Check for sources of interference. Ensure the receiver is not too close to other RF devices.
9. User Tips
- Quick Setup: Users have noted the product is easy to set up and works well, suggesting a straightforward installation process.
- Reliability: The product is generally considered reliable and of excellent quality.
- Versatility: The ability to control both lights and motors makes it a flexible solution for various automation needs.
10. Warranty and Support
This product comes with a 1-year warranty for the 433MHz Garage Motor Door Controller. For any questions or support, please contact the manufacturer:
Manufacturer: Huizhou Wenqiao Electronic Technology Co., Ltd.
Address: Room 03, 12th Floor, Building T19, East Coast Garden, Fangzhilonghuwan, No. 27, Sanhuan South Road, Huicheng District, Huizhou City, Guangdong Province, China 516001
WhatsApp: +86 135 0227 8583 / +86 158 7521 8992
Email: dieseelectronic@163.com
10.1. Certifications
The product is certified with RoHS, CE, and CCC standards, ensuring compliance with environmental and safety regulations.

Figure 8: Quality Assurance (RoHS/CE)