AutoXbert Car Roof Aerial Antenna Mount Base

Contents

AutoXbert Car Roof Aerial Antenna Mount Base Instruction Manual

Model: Car Roof Aerial Antenna Mount Base

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your new Car Roof Aerial Antenna Mount Base. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Car roof antenna base installed on a vehicle, with a close-up of the antenna base in the foreground.
The Car Roof Aerial Antenna Mount Base installed on a vehicle.

2. Safety Precautions

  • Installation Safety: Ensure the vehicle is turned off and power is disconnected before installation. When working on the roof, be careful to avoid slipping and ensure the ladder or bracket is stable.
  • Driving Safety: The total height of the antenna after installation must not exceed the vehicle's legal height limit to ensure it will not be damaged or endangered when entering underground parking garages, automatic car washes, or encountering obstacles.
  • Electrical Safety: Insulation protection should be provided at antenna cable connections to prevent short circuits with other vehicle circuits.

3. Installation Guide

3.1 Location Selection and Preparation

  • Preferred Location: The center of the roof or rear of the vehicle is the best signal reception location. The trunk lid or fender are common alternative locations.
  • Inspection: Confirm that there are no vehicle structural reinforcements, wiring harnesses, or airbag components below the installation location.
  • Removal of Existing Parts: If replacing, carefully remove the original antenna first. It can usually be unscrewed by rotating counterclockwise.

3.2 Base Installation

  1. Threading: Thread the antenna cable through the external mounting hole into the vehicle (if a pre-drilled hole is available, or professional drilling is required). For roofs without mounting holes, it is strongly recommended that a professional drill the hole at a suitable location.
  2. Sealing: Apply a suitable amount of sheet metal sealant evenly around the mounting hole under the base. Place the matching waterproof gasket between the base and the vehicle body.
  3. Securing: Tighten the base bolts from the inside of the vehicle using washers and fixing nuts, ensuring the base fits tightly against the vehicle body without wobbling, while avoiding overtightening to prevent paint or sheet metal deformation.
  4. Drainage: Ensure that the base structure does not obstruct the vehicle's drainage path after installation.
Close-up view of the underside of the antenna mount base, showing the threaded bolt and internal components.
Underside view of the antenna base, showing the threaded bolt for securing.
Close-up view of the female threaded hole on the antenna mount base.
Close-up of the female threaded hole for the antenna mast.

3.3 Antenna Mast Installation and Cable Connection

  1. Connection: Screw the threaded end of the antenna mast clockwise into the interface on the top of the base. Tighten by hand, then lightly tighten another 1/4 turn with a small wrench (do not overtighten).
  2. Wiring: Conceal the coaxial cable leading from the base along the edge of the interior trim panel or the original vehicle wiring harness to the back of the radio head unit.
  3. Connecting: Securely connect the female connector of the antenna cable to the male connector (marked "ANT") on the back of the radio unit.
  4. Securing: Secure the cable in sections using cable harness clips to prevent rattling while driving.
Top-down view of the antenna mount base, showing the internal mechanism for the antenna mast.
Top view of the antenna base, showing the connection point for the mast.

4. Operation

4.1 Telescopic Antenna (if applicable)

  • To extend: Hold the top of the antenna and gently pull it upwards to its longest position (usually you'll feel a "click" to lock it in place).
  • To retract: First lift slightly upwards to unlock, then slowly press downwards.
  • Recommendation: It is recommended to retract the antenna for protection when washing the car, passing through automatic car washes, or parking for extended periods.

4.2 Signal Check

After installation, start the vehicle and turn on the radio. Manually search for several known strong radio stations to check if the reception is clear and stable, comparing the results to before installation.

5. Maintenance

  • Regular Inspection: Check the antenna base seal monthly for integrity and any signs of water leakage; check the antenna mast's tightness.
  • Cleaning: Wipe the antenna mast with a damp cloth. Avoid using a high-pressure water gun to directly wash the base seams.
  • Corrosion Prevention: In coastal or high-salinity areas, apply a small amount of petroleum jelly to the antenna threads periodically to prevent rust.
  • Signal Interference: If the addition of other electronic equipment (such as a high-powered mobile radio or inverter) causes noise in the radio, it may be necessary to check the cable shielding or add a filter.

6. Troubleshooting

6.1 No Radio Signal, Loud Noise

Possible Causes:

  • Antenna not tightened
  • Cable not connected or loose
  • Internal damage to antenna or cable

Troubleshooting Suggestions:

  1. Check and tighten the antenna mast.
  2. Check the connector at the rear of the main unit.
  3. Test with a spare antenna to rule out antenna damage.

6.2 Poor Signal in a Specific Direction/Area

Possible Causes:

  • Antenna position not ideal
  • Local signal shielding

Troubleshooting Suggestions:

  1. This may be a physical limitation; try adjusting the radio frequency fine-tuning (if supported).

6.3 Water Leaking into the Car Headliner

Possible Causes:

  • Base gasket aged or damaged
  • Improper sealing during installation

Troubleshooting Suggestions:

  1. Replace the gasket.
  2. Disassemble and reapply sealant before installation.

7. Specifications

Feature Detail
Item Type Aerials
Model Name Antenna Aerials
Special Features Car roof aerial base
External Testing Certification iso9001
OEM NO. 9628851980, 656110, 6561CX
Material ABS (base), Stainless steel/Aluminum alloy (antenna mast)
Item Weight 0.04kg
Is wireless No
High-concerned chemical None
Impedance 50 Ω or 75 Ω (must match the main unit)
Frequency Range FM 87.5-108 MHz; AM 520-1710 kHz (basic model)
Gain Approx. 0~3 dBi (Passive)
Installation Torque 1.5~2.5 N·m
Operating Temperature -30°C~+80°C
Diagram showing the dimensions of the antenna mount base in centimeters and inches.
Dimensions of the antenna mount base.

8. Vehicle Compatibility

This antenna mount base is compatible with a wide range of vehicles. Please verify your vehicle's OEM part number against the provided reference part number (9628851980) to ensure compatibility.

For CITROEN:

  • AX ZA- 1986-1998 HATCHBACK
  • BERLINGO MF 1996-2016 MPV, M_ 1996-2016 BOX, B9 2008-ONWARD MPV & BOX & PLATFORM/CHASSIS, BERLINGO/BERLINGO FIRST MF 1996-2011 MPV
  • BX BX_1982-1994 HATCHBACK & ESTATE
  • C15 VD-1984-2005 BOX, --1987-2000 ESTATE
  • DISPATCH U6U 1995-2016 MPV, BU_, BV_, BW_,BX_ 1999-2006 PLATFORM/CHASSIS, BS_,BT_,BY_,BZ_ 1995-2016 BOX, -- 2007-ONWARD PLATFORM/CHASSIS
  • SAXO S0, S1 1996-2004 HATCHBACK
  • SYNERGIE 22,U6 1994-2002 MPV
  • XANTIA X2 1998-2003 HATCHBACK & ESTATE, X1 1993-2003 HATCHBACK & ESTATE
  • XM Y4 1994-2000 HATCHBACK & ESTATE, Y3 1989-1994 HATCHBACK & ESTATE
  • XSARA N2 1997-2005 ESTATE, N1 1997-2005 HATCHBACK, N0 1998-2005 COUPE, -- 1998-2005 BOX/ESTATE
  • ZX N2 1001-1998 HATCHBACK, N2 1991-1998 ESTATE

For FIAT:

  • SCUDO 220L 1996-2006 BOX, 220_1996-2006 PLATFORM/CHASSIS, 220 1996-2006 BOX
  • ULYSSE 220 1994-2002 MPV

For PEUGEOT:

  • 106 MK 2 1996-2004 HATCHBACK, 1A, 1C 1991-1996 HATCHBACK, 1_ 1991-2001 BOX
  • 206 2A/C 1998-ONWARD HATCHBACK, 2A/C 1998-2016 HATCHBACK, 2A/C 1998-2008 HATCHBACK, -- 1999-2016 BOX, -- 1999-2010 SALOON, -- 1999-2010 BOX, SW 3E/K 2002-2015 ESTATE, + T3E 2009-ONWARD HATCHBACK
  • 306 N_,7_ 1994-2002 BOX/ESTATE, 7E, N3, N5 1995-2002 ESTATE, 7D, N3, N5 1994-2001 SALOON, 7B, N3, N5 1994-2001 SALOON, 7A, 7C, N3, N5 1993-2003 HATCHBACK, -- 1993-2001 BOX BODY/HATCHBACK
  • 405 MK2 1992-1999 SALOON, MK2 1992-1999 ESTATE, 15E 1987-1992 ESTATE, 15B 1987-ONWARD SALOON
  • 406 8E/F 1996-2004 ESTATE, 8C 1997-2004 COUPE, 8B 1995-2004 SALOON
  • 806 221 1994-2002 MPV
  • EXPERT VF3A_, VF3U_, VF3X_ 2007-ONWARD BOX, 224 1996-2006 MPV, 223 1996-2006 PLATFORM / CHASSIS, 222 1996-2006 BOX, -- 2007-ONWARD PLATFORM/CHASSIS
  • PARTNER 5F 1996-2015 MPV, 5 1996-2015 BOX, -- 1999-ONWARD PLATFORM/CHASSIS, -- 1999-ONWARD BOX, ORIGIN 5F 1996-2015 MPV

Also Fits:

  • For TOYOTA AYGO

9. Package Contents

  • 1 * Car roof aerial base
Image of the antenna base in its packaging, showing a label.
The antenna base as typically packaged.

10. User Tips

  • Gasket Check: Always ensure that a sealing gasket is present and in good condition before installation to prevent water infiltration. If a gasket is missing or damaged, acquire a suitable replacement.
  • Compatibility Verification: Double-check the product's compatibility with your specific vehicle model and year, ideally by comparing OEM part numbers, to ensure a perfect fit and optimal performance.
  • Secure Fitment: Ensure all connections are tightened appropriately, but avoid overtightening to prevent damage to the antenna base or vehicle body. A secure fit is crucial for both signal quality and preventing leaks.

11. Warranty and Support

11.1 Warranty Statement

This product offers a limited warranty against defects in materials or workmanship (specific period is detailed on the warranty card). The following are not covered under warranty: malfunctions caused by improper installation, vehicle accidents, human-caused damage, unauthorized modifications, failure to follow the instructions, or normal wear and tear.

11.2 Important Note for GPS/Satellite Functionality

For antennas with integrated GPS/satellite signal functionality, the installation location must ensure an unobstructed view of the sky and no large metal objects obstructing the view.

11.3 Professional Installation Recommendation

This instruction manual is a general guideline; specific installation steps may vary significantly depending on the vehicle model and antenna type. For installations requiring drilling or involving complex interior disassembly, it is strongly recommended to have them performed by a professional auto detailing shop or repair shop to ensure installation quality, waterproofing, and vehicle safety.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.