BONDA Wall Touch Switch User Manual

1. Introduction

This manual provides instructions for the safe and efficient installation, operation, and maintenance of your BONDA Wall Touch Switch. This EU standard touch switch features a tempered crystal glass panel, offering an elegant and stylish solution for controlling lighting in homes, hotels, and offices.

2. Important Safety Information

• Always cut off the power supply before installation or maintenance to prevent electric shock.
• Do not install in damp environments.
• Do not exceed the maximum load specified.
• Ensure proper wiring according to the provided diagrams.
• The switch must be installed without electricity. Power must be turned on after the installation and covering of the glass touch panel. Wait 10 seconds before testing.
• Not suitable for factories, hospitals, CT/nuclear magnetic resonance rooms, and other places with strong electromagnetic interference.

3. Product Features

• 1/2/3 Gang touch switch, 220V EU Standard.
• Toughened crystal glass panel design: elegant, stylish, no fading, waterproof, and scratch-resistant.
• Super sensitivity: light touch operation.
• Available in popular colors: Black, White, Golden.
• Blue LED indicator: distinguished design, glows at night for easy location.
• New imported IC processor for nice sensitivity and stable performance.
• High temperature resistant PC material base for durability and longer life.
• Single live wire control: easy to install, direct replacement for old switches.
• Touch control ensures longer service life than traditional switches.
• Protection of over-current, anti-interference.
• Certifications: CE, RoHS.
• Easy to clean, panel glass resists deformation and fading.
• Elegant look, suitable for various modern decor styles (drawing room, bedroom, corridor, kitchen, bathroom, office).

4. Specifications

5. Installation Guide

Important: Ensure electricity is cut off at the main breaker before starting installation to prevent electric shock.

5.1. Components

5.2. Step-by-Step Installation

1. Remove the Panel: Carefully remove the glass panel using a screwdriver. (Do not install with power on).
2. Prepare Wiring:
   • Connect the live wire to the "L" terminal on the switch.
   • Connect the lamp wire(s) to the "L1", "L2", or "L3" terminal(s) as appropriate for your setup (1, 2, or 3 gang).
3. Fix Switch to Wall:
   • Place the switch into the wall switch box.
   • Secure it using the two side screws.
   • Install the glass panel by sliding it down from above.
   • Turn on the electricity.
   • Wait 10 seconds after installation before touching the panel to test.

5.3. Wiring Diagram

5.4. Capacitor Installation (for LED/Energy Saving Bulbs)

If you are using LED or energy-saving bulbs, and the lamp appears shiny or flickering, you may need to install the included yellow capacitor. This capacitor should be installed between the neutral wire (N) and the live wire (L1) of the lamp (at the bulb fixture, not at the switch). This helps stabilize the circuit and resolves flickering issues.

6. Operating Instructions

6.1. Basic Operation

The touch switch operates by lightly touching the designated area on the glass panel. A light touch is sufficient for activation.

6.2. Backlighting

The switch features an LED indicator for visual feedback:

• When the light is OFF, the indicator glows blue, making it easy to locate the switch in the dark.
• When the light is ON, the indicator turns red.

6.3. Remote Control Pairing (for compatible remote switch series only)

This section applies only if you have a compatible remote control for your switch. The switch operates on RF Frequency 433.92MHz.

To turn ON/OFF with a remote button:

1. Press and hold the touch button on the switch for a few seconds until it rings a single beep.
2. Then, press any key on the remote control. ON/OFF control will be realized.

To turn ON with a remote button:

1. Press and hold the touch button on the switch for a few seconds until it rings two beeps.
2. Then, press any key on the remote control. ON control will be realized.

To turn OFF with a remote button:

1. Press and hold the touch button on the switch for a few seconds until it rings three beeps.
2. Then, press any key on the remote control. OFF control will be realized.

To clear the remote control code:

1. Press and hold the touch button on the switch for a few seconds until it rings four beeps. The code will be cleared.

6.4. Dimmer Switch Operation (for compatible dimmer switch series only)

This section applies only if you have a compatible dimmer switch.

To turn ON/OFF:

1. Press the touch button until the backlight flashes once.
2. Then, press the remote control button.

To dim the light (down):

1. Press the touch ON/OFF button until the backlight flashes twice.
2. Then, press any key on the remote control.

To dim the light (up):

1. Press the touch ON/OFF button until the backlight flashes three times.
2. Then, press any key on the remote control.

To clear the code:

1. Press the touch ON/OFF button until the backlight flashes four times. The code will be cleared.

7. Maintenance

• Cleaning: The flat mirror glass panel is easy to clean. Use a soft, damp cloth to wipe the surface. Avoid abrasive cleaners.
• Durability: The tempered glass panel is designed to be explosion-proof, fall-resistant, and scratch-resistant.
• Flame Retardant Materials: The bottom shell is made of flame retardant and high-temperature resistant PC material, enhancing safety against short circuits.

8. Troubleshooting / Common Fault Diagnosis

8.1. Lamp appears shiny or flickering:

Solution: Connect the yellow capacitor (included) between the neutral wire (N) and the live wire (L1) of the lamp (at the bulb fixture). This stabilizes the circuit and resolves flickering issues, especially with LED or energy-saving bulbs.

8.2. Switch is installed, but no reaction to touch:

Solution:

1. Verify that the wiring is correctly connected according to the wiring diagram.
2. Ensure the lamp is properly connected and not damaged.
3. Disconnect the power supply for 1 minute.
4. Reinstall the switch, ensuring the glass panel is properly covered.
5. Turn on the power.
6. Wait 10 seconds, then touch to test.

8.3. Light turns on and off immediately:

Solution: This often indicates incorrect wiring or a need for the capacitor. Double-check that the live wire is connected to 'L' and the lamp wire to 'L1' (or L2/L3). If using LED/energy-saving bulbs, ensure the capacitor is installed as described in section 5.4.

8.4. Constant light flashes every 10 seconds when off:

Solution: This is typically resolved by installing the capacitor between the neutral wire and the bulb's live wire (L1), as described in section 5.4.

8.5. Not a smart switch / No WiFi:

Clarification: This specific model (605N/B605N) is a touch-sensitive wall switch and is NOT a smart device with WiFi connectivity or compatibility with systems like Alexa or Google Home.

9. User Tips

• Capacitor Use: If you experience flickering or the light turning on/off unexpectedly, especially with LED bulbs, ensure the included capacitor is installed between the neutral wire and the bulb's live wire (L1) at the lamp fixture.
• Installation Patience: After installation and powering on, wait approximately 10 seconds before testing the touch functionality. This allows the switch to initialize properly.
• Cleaning: The tempered glass panel is easy to clean with a soft, damp cloth.
• Two-Way/Commutated Switches: This model is designed for single-point control. If you require a two-way (commutated) switch setup, this specific model may not be suitable, as the manufacturer typically does not offer commutated versions for this series.

10. Warranty and Support

This product comes with a 1-year warranty from the date of purchase.

For detailed information and further assistance, please refer to the official user manual PDF available from the seller. (PDF reference: https://manuals.plus/m/fd42c0d93d2fe3fc007f2207e7de7646c9e9e3120162d4ae20a0c7b398459dbf)