SZRZGT LED Driver Transformer Power Supply Adapter

Contents

SZRZGT LED Driver Transformer Power Supply Adapter User Manual

Models: 24-36X1W, 12-18X3W, 18-25X3W, 30W

1. Introduction

This manual provides essential information for the safe and efficient use of your SZRZGT LED Driver Transformer Power Supply Adapter. Please read this manual thoroughly before installation and operation, and keep it for future reference. These LED drivers are designed to provide stable power to various LED lighting applications.

Product demonstration video showcasing the various models of SZRZGT LED Drivers, highlighting their physical appearance and different sizes.

2. Safety Precautions

Adhering to these precautions is crucial for safe operation and to prevent damage to the LED driver and connected equipment.

  1. The input voltage must be strictly within the nominal operating voltage range specified. Exceeding this range can trigger protection or cause permanent damage.
  2. Do not use in high-temperature, sealed environments. Ensure good heat dissipation to prevent overheating.
  3. Creepage distance and electrical clearance of the light source board must comply with UL8750/IEC 60598-1 safety standards.
  4. Recommended LED bead arrangement: "parallel first, then string". Minimize copper coating area while meeting flow capacity.
  5. Do not parallel the output terminals or auxiliary sources of two or more LED driver power supplies.
  6. Some models may require auxiliary heat dissipation plates. Refer to product specifications for details.
  7. For non-isolated drive power supplies:
    • Configure a leakage protector for the input front-end.
    • Ensure insulation withstand voltage of the supporting lamp board is at least 3kV (4kV or above recommended).
    • During production and use, avoid short circuits between positive/negative poles of the output and ground.
    • Do not directly conduct voltage withstand tests between "input-output" terminals.

3. Specifications

Below are the general and model-specific specifications for the LED drivers.

General Specifications:

  • Brand Name: SZRZGT
  • Item Type: Lighting Transformers
  • Origin: Mainland China
  • Nominal Voltage: 10-50V
  • Output Voltage: 85-265V (Input range)
  • High-concerned chemical: None
  • Plug Type: None
  • Dimensions (Approximate): 111mm x 42mm x 27mm (for most models)

Model-Specific Specifications:

ModelInput VoltageOutput Voltage (Load Test AC230V)Output Current
24-36X1W Driver85-265V90-128V280-300mA
12-18X3W Driver85-265V30-60V600mA
18-25X3W Driver85-265V55-100V600mA
30W Driver85-265V20-38V900mA

Note: No-load testing is forbidden as it can yield inaccurate data and potentially damage the unit.

Close-up of the HJY24-36X1W LED Driver, showing input AC85-265V, output DC90-128V, 300mA, and CE marking.

HJY24-36X1W LED Driver (24-36W, 300mA)

Close-up of the HJY12-18X3W LED Driver, showing input AC85-265V, output DC30-60V, 450mA/600mA, and CE marking.

HJY12-18X3W LED Driver (12-18W, 600mA)

Close-up of the HJY18-25X3W LED Driver, showing input AC85-265V, output DC55-100V, 600mA, and CE marking.

HJY18-25X3W LED Driver (18-25W, 600mA)

Close-up of the HY30W LED Driver, showing input AC85-265V, output 20-38V, 900mA, and CE marking.

HY30W LED Driver (30W, 900mA)

4. Setup and Installation

4.1. Installation Method

  1. Installation must strictly comply with IEC/EN 60598-1, IEC/EN 61347, or national standards GB 4706.1 and GB 7000.1 safety specifications.
  2. Ensure reliable grounding. The current capacity of the grounding line must be > 25A, and grounding resistance less than 0.1 Ω. Do not use lamp posts or housings as grounding media.
  3. The power supply must be installed horizontally and securely fixed with screws. Do not install vertically on lamp posts or suspend using input/output wires.
  4. For Class I LED driver power supply, do not suspend its input ground wire (PE wire). Achieve effective grounding through a dedicated grounding device, ensuring good electrical contact between the power supply housing and lamp housing.
  5. Do not directly expose or attach the power supply to the heat sink of the lighting fixture. Design a dedicated protective chamber or install reliable waterproof facilities.
  6. Do not use indoor power sources directly outdoors. For outdoor use, install a lightning arrester of no less than 10kV at the AC input terminal.
  7. Install the power supply away from combustible materials (wood, flammable plastics) and avoid areas with strict smoking prohibitions (unless explosion-proof certified).
  8. Secure the power supply horizontally with screws. Do not modify or damage the power supply structure, and do not stack or install multiple power supplies without gaps.

4.2. Wiring Diagram

The general wiring connection for the LED driver is as follows:

  • AC Input: Connect your main AC power supply to the input terminals of the LED Driver. Ensure correct polarity (Live, Neutral).
  • LED Driver: The driver converts the AC input to the appropriate DC output for your LEDs.
  • LED Luminaire: Connect the output terminals of the LED Driver to your LED luminaire. Ensure correct polarity (Positive, Negative).
  • Protective Earth (PE): For models that include it, connect the PE terminal from the AC input to the LED Driver, and from the LED Driver to the LED Luminaire for safety.

Always refer to the labels on your specific LED driver for exact input (L, N) and output (+, -) connections.

5. Operating Instructions

Once properly installed and wired according to the instructions above, the LED driver will power your LED luminaire. Ensure all connections are secure before applying power.

5.1. Testing and Assembly Precautions

  1. When wiring, strictly follow the power label identification. Do not connect input and output in reverse. Confirm all wiring is correct and reliable before powering on.
  2. Do not allow input lines, output lines, dimming lines, programming lines, and auxiliary power lines to contact each other or other live objects.
  3. When conducting power withstand voltage level testing, strictly follow specifications and standards. Over-specification testing is prohibited.
  4. For auxiliary power lines, programming lines, and dimming lines not in use, perform separate insulation and waterproof treatment.
  5. If adjusting a potentiometer (if present), the adjustment force should not exceed 500g·cm. Use a plastic screwdriver.
  6. Lay AC input lines, output lines, auxiliary power lines, and dimming lines separately to avoid long-distance close proximity and parallelism, preventing signal crosstalk.
  7. During aging tests on LED lamps, place them reasonably to avoid direct light from one lamp shining on the power or heat dissipation parts of another lamp, preventing power monitoring caused by local overheating if the temperature at point (TC) exceeds the standard.

6. Maintenance

  • Keep the LED driver in a clean, dry environment.
  • Ensure proper ventilation around the unit to prevent heat buildup.
  • Regularly check for any loose connections or signs of physical damage.
  • Do not attempt to open or repair the unit yourself, as this may void any warranty and poses a safety risk.

7. Troubleshooting

ProblemPossible CauseSolution
LEDs not lighting upNo power to driver, incorrect wiring, faulty LED, driver failure.Check power supply, verify all wiring connections (input/output polarity), test LED separately, replace driver if necessary.
LEDs flickeringUnstable input voltage, loose connection, incompatible LED load, driver overheating.Ensure stable input power, check all connections, verify LED load matches driver specifications, ensure adequate ventilation.
Driver is hot to touchOverload, insufficient ventilation, high ambient temperature.Reduce LED load to within driver limits, improve ventilation, ensure ambient temperature is within operating range.

If troubleshooting steps do not resolve the issue, consult a qualified electrician or contact customer support.

8. User Tips

  • Always double-check input and output voltage/current requirements of your LEDs against the driver's specifications to ensure compatibility.
  • When working with electrical components, always disconnect power at the source before making or changing any connections.
  • Consider using appropriate wire gauges for your connections to prevent overheating and ensure efficient power delivery.

9. Warranty and Support

For warranty information and technical support, please refer to the seller's terms and conditions or contact your point of purchase. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.