1. Introduction
The Heltec Active Balancer/Equalizer is designed to optimize the performance and lifespan of lithium battery packs. It utilizes high-frequency transformer inversion and equipotential isolation coupling energy technology to achieve precise and efficient cell balancing. This module is suitable for high-capacity ternary lithium and lithium iron phosphate battery packs, supporting 4S to 24S configurations with an equalizing current of up to 8A.
The intelligent MCU control chip, combined with an ultra-low dynamic impedance inverter, ensures a balanced effect of ≤ 30mV, helping to maintain battery health and restore capacity.

2. Product Features
- Advanced Balancing Technology: Features a nano amorphous isolated fully symmetrical transformer for minimal voltage difference and an ultra-low internal resistance MOS device inverter circuit for high power balance.
- Intelligent Control: An intelligent MCU chip provides automatic self-balancing capabilities.
- Battery Protection: Automatically detects minimum battery voltage, stopping operation when energy is low to prevent power loss.
- Safety Mechanisms: Includes overcurrent fuse resistance at each series input and a miniature circuit breaker for over-temperature and over-current protection.
- Dual Operating Modes: Supports both automatic and manual trigger modes for equalization.
- Efficient Heat Dissipation: Designed for effective heat dissipation even under extreme equilibrium states with high voltage differences.
3. Technical Specifications
| Parameter | Value |
|---|---|
| Product Name | Lithium battery pack transformer inverter active equalization module |
| Applicable Battery Type | Lithium Ternary / Lithium Iron Phosphate |
| Applicable Battery Strings | 4S-24S |
| Best Balance Effect | 0.01~0.03V |
| Recommended Equalizing Battery Voltage | Above 3.2V |
| Equalizing Current | 0~5A/8A |
| Interface | 3.81 |
| Low Voltage Automatic Shutdown | 2.7V (2.5V)/strings |
| Equalization Mode | Parallel Energy Transfer Mode |
| Power Consumption (Standby Load) | < 5mA (12V power supply of the fourth string) |
| Power Consumption (Balance State) | 80mA (voltage difference ≥10mV) |
| Auto Start Trigger Voltage | +70mV |
| Automatic Startup and Shutdown Voltage | +20mV |
| Voltage Range | No voltage |
| Electronic | No |
| Charger Included | No |
| Battery Included | No |
| Accessory Type | Battery Accessories |
| Origin | Mainland China |
| Certification | CE |


4. Package Contents
Upon opening the package, please verify that all the following items are included:
- Active equalization module x 1
- Line sequence detection board x 1
- 3.81 cable interface x 1
- Slotted screwdriver x 1
- 0.5mm² electronic wire x 1
5. Setup & Installation
Proper installation is crucial for the safe and effective operation of your active balancer. Please follow these steps carefully.
5.1. Wiring Preparation
- Solder Wires: Solder the provided wires to your battery pack in the correct order. Ensure a secure connection for each cell.
- Install Socket Terminal: After soldering, install the 3.81mm socket terminal onto the soldered wires.
- Connect Terminals: Connect the 3.81mm terminals in order, ensuring the negative terminal of the battery pack (B-) connects to B0 on the balancer.
- Secure Cables: Use the knob screws on the terminal block to firmly fix the cables.
- Handle Extra Parts: If your battery pack has fewer strings than the balancer supports (e.g., 20S on a 24S balancer), leave the extra terminal slots blank.
5.2. Wire Sequence Testing
Before connecting the equalizing board to the battery pack, it is critical to test the wire sequence to prevent damage.
- Use Detection Board: Connect the wires from your battery pack to the provided line sequence detection board.
- Verify Correct Connection: When the positive and negative wire sequence of the battery pack is correctly connected, the corresponding LED light on the detection board will be red.
- Check for Reverse Polarity: If the sequence connection of two strings of wires is reversed, the detection board will indicate a balanced arrangement of wires, which is incorrect. Correct any reversed connections immediately.
- Connect B0: Ensure the interface B0 on the balancer connects to the negative pole (black wire) of your battery pack.
Warning: An incorrect wire sequence will damage the equalizing board. Damaged boards cannot be returned or replaced.
5.3. Connecting to the Balancer
- Once the wire sequence is verified, connect the terminal block from the battery pack to the corresponding port on the active equalization module.
- Ensure all connections are firm and correctly aligned.
5.4. Cascade Connection (for >24S battery packs)
For battery packs with more than 24 strings, multiple active equalizers can be cascaded. The wiring schematic involves connecting the output of one balancer to the input of the next, ensuring multiple strings of repeated connections for optimal effect. The more repeated strings, the better the balancing effect.
- Two active balancers: For 25S~44S battery packs.
- Three active balancers: For 45S~64S battery packs.
- Four active balancers: For 65S~84S battery packs.
- Five active balancers: For 85S~104S battery packs.
- Six active balancers: For 105S~124S battery packs.
- Seven active balancers: For 125S~144S battery packs (and so on, for infinite cascading).
5.5. Installation Video Guide
For a visual demonstration of the installation process, please refer to the official video:
6. Operating Instructions
The Heltec Active Balancer offers two main equilibrium modes:
6.1. Continuous Equilibrium Mode
- Ensure the white self-locking switch on the balancer is in the 'off' position.
- Connect the wiring in sequence, ensuring correct wire sequence as verified during setup.
- Press the white self-locking switch to initiate continuous equalization.
- During continuous equalization, the negative pole LED will be lit, and the positive pole LED will flicker.
- To stop continuous equalization, manually press the switch again.
6.2. Forced Equilibrium Mode
- Ensure the white self-locking switch is in the 'off' position.
- Connect the wiring in sequence, ensuring correct wire sequence.
- Double-click the black touch switch on the left side of the balancer to start the forced equalization mode.
- The balancer will automatically stop after one hour in this mode.
- During timed equalization, the positive pole LED will flicker.
6.3. Working Principle Overview
The balancer operates based on a parallel energy transfer mode. When the voltage drop across the protection board reaches 70mV or above (this current is related to the internal resistance of the MOS tube on the protection board), the active equalizer automatically starts the balancing process. High voltage energy is transferred to lower voltage cells to achieve overall battery voltage balance.
7. Maintenance
To ensure the longevity and optimal performance of your Heltec Active Balancer, consider the following maintenance guidelines:
- Keep Clean: Regularly inspect the module for dust or debris. Use a soft, dry brush or compressed air to clean the heatsinks and PCB.
- Check Connections: Periodically verify that all wire connections are secure and free from corrosion. Loose connections can lead to reduced performance or damage.
- Environmental Conditions: Operate the balancer within its specified temperature and humidity ranges. Avoid exposure to extreme temperatures, moisture, or corrosive environments.
- Physical Inspection: Check for any signs of physical damage, such as cracked components or damaged wiring. Address any issues promptly.
8. Troubleshooting
If you encounter issues with your active balancer, refer to the following common problems and solutions:
8.1. Balancer Not Activating or Poor Balancing Effect
- Incorrect Wiring Sequence: Ensure the wire sequence is correct. An incorrect sequence can damage the balancer. Always use the line sequence detection board before connecting.
- High Resistance Connections: The equalizing current is affected by the internal resistance of the battery pack, connecting cables, and connector contact resistance.
- Solution: Use larger cross-sectional area and shorter connecting wires. Consider direct wire connection instead of connectors if possible to reduce contact resistance (connect equalizer end first, then battery pack end).
- Cable Thickness: For optimal balanced current, use 0.5mm²/A for connecting wires. If extending cables, increase conductor section proportionally.
- Low Voltage Difference: In the final stages of equalization, when the voltage difference is very small (<10mV), the current will also be very small, making the process appear slow. This is normal.
- Overcurrent on BMS Protection Cable: The BMS protection cable is a signal line. Overcurrent (< 2A) can affect the balanced effect.
- Solution: Re-weld the cable with a thickness of ≥0.5mm².
8.2. Balancer Damaged After Connection
- Incorrect Wire Sequence: This is the most common cause of damage. Always test the wire sequence with the detection board before connecting the balancer to the battery pack.
8.3. Measuring Equalizing Current
- Do Not Use Ammeter Directly: Connecting an ammeter directly in series will increase the loop resistance and reduce the measured equalizing current.
- Recommended Tool: Use a DC Clamp ammeter for accurate measurement without affecting the circuit.
9. User Tips
Here are some tips from experienced users to help you get the most out of your Heltec Active Balancer:
- Prioritize Wire Sequence: Always double-check your wiring sequence with the provided detection board before making the final connection to the balancer. This is the most critical step to prevent damage.
- Optimize Cable Gauge: For maximum balancing efficiency, especially with higher currents, ensure your connecting wires are of adequate thickness (e.g., 0.5mm²/A). Thicker, shorter wires reduce resistance.
- Consider Direct Connections: If you're comfortable with soldering, direct wire connections can offer better performance than terminal blocks due to lower contact resistance.
- Understand Balancing Speed: Don't be alarmed if balancing seems slow when cell voltage differences are minimal. The balancer works continuously to maintain equilibrium, and the current naturally decreases as cells become more balanced.
- Utilize Forced Mode: The forced equilibrium mode can be useful for quickly addressing larger imbalances or for initial setup, as it ensures balancing for a set period.
10. Support & Contact Information
For further assistance or inquiries, please contact Heltec BMS:
- Website: www.Heltec-BMS.com
- E-mail: echo@heltec.cn
- Tel: 18123313360
- Address: 64th ChengHong road, chenghua Section, Chengdu, SiChuan, China
A detailed user manual in PDF format is also available for download from the official website.