CHANZON Universal Circuit PCB Board Assortment Kit

Contents

CHANZON Universal PCB Board Kit Instruction Manual

Model: Universal Circuit PCB Board Assortment Kit

Brand: CHANZON

1. Introduction

This manual provides essential instructions and safety information for the CHANZON Universal PCB Board Kit. This kit contains 34 pieces of double-sided, tinned, FR4 grade perfboards designed for prototyping and constructing permanent or semi-permanent electronic circuits via soldering. These boards are ideal for hobbyists, students, and professionals in electronics.

Assortment of CHANZON universal PCB boards in various sizes
Figure 1: Overview of the CHANZON Universal PCB Board Kit, showing various sizes and RoHS compliance.

2. Safety Information and Warnings

Please read and understand all safety warnings before using this product. Failure to follow these instructions may result in injury, electric shock, fire, or damage to the product.

  • Electrical Safety Warning:
    ▲ Circuits assembled using this product may contain hazardous voltages and currents. Incorrect design or wiring may result in short circuits, overheating, fire, or electric shock. Thoroughly verify all connections before powering up the assembled circuit. Initial testing is recommended using a low-voltage DC power supply (e.g., laboratory power supply) with current limiting enabled.
  • High-Temperature and Burn Warning:
    ▲ Soldering involves high temperatures. The soldering iron tip, molten solder, and freshly soldered PCBs reach extremely high temperatures capable of causing severe skin burns. Always place the soldering iron in its designated stand during use, and wear an anti-static wrist strap (when properly grounded). Keep the work area clear of flammable materials. Allow solder joints and the PCB to cool completely before handling.
  • Mechanical Processing and Health Warning:
    ▲ Cutting, grinding, or milling copper-clad boards generates sharp fiberglass fragments and fine copper dust. Safety goggles and an N95-rated (or higher) dust mask must be worn at all times. Perform such operations only in a well-ventilated area equipped with local exhaust ventilation or dust collection systems, and dispose of waste materials appropriately.
  • Child Safety and General Warning:
    ▲ Not suitable for children under 14 years of age. This product and its accessories (e.g., loose components) may contain small parts. Circuit assembly and soldering involve complex procedures and inherent hazards. To be used under the direct supervision of an adult or qualified instructor. Recommended only under the guidance of an adult possessing relevant safety knowledge and technical competence.

3. Product Overview

The CHANZON Universal PCB Board Kit provides high-quality prototyping boards with the following features:

  • Material: FR4 Grade Fiberglass, known for its durability and electrical insulation properties.
  • Design: Double-sided with pre-tinned, plated through-holes for easy soldering and robust connections.
  • Hole Type: Electrically isolated holes, not stripboard, allowing for flexible circuit layouts.
  • Compliance: RoHS compliant and lead-free (Pb-free).
  • Precision: Embossed print for precise hole alignment.
Diagram showing features like plated through holes, isolated holes, corner mounting holes, and double-sided board
Figure 2: Key features of the PCB boards, including plated through-holes and double-sided FR4 construction.
Comparison of PCB thickness, showing CHANZON board at 1.60mm (FR-4) versus a thinner 1.24mm board (FR-1)
Figure 3: Quality comparison highlighting the 1.6mm thickness and FR4 grade of CHANZON boards.
Comparison of hole alignment, showing CHANZON's embossed print for precise alignment versus misaligned holes on other boards
Figure 4: Detail showing the precise embossed print and hole alignment of CHANZON PCBs.

4. Setup and Usage

4.1 Workbench Preparation

Operate on a clean, dry, well-lit, and well-ventilated workbench. Before handling, discharge static electricity from your body (e.g., by touching a grounded metal object), especially when working with electrostatic-sensitive components.

4.2 Soldering

  1. Use a temperature-controlled soldering iron (recommended 300-350°C).
  2. Follow the principle of "mechanical fixation first, then soldering." Secure components before applying solder.
  3. Limit dwell time per solder joint to no more than 3 seconds to prevent pad delamination due to overheating.
  4. Ensure proper ventilation to avoid inhaling solder fumes.

4.3 Cutting/Milling

When cutting or milling these boards, wear safety goggles and an N95-rated (or higher) dust mask. Perform operations only with professional tools (e.g., hobby knives, PCB milling machines) and properly collect fiberglass and copper debris.

4.4 Cleaning

After soldering or processing, clean flux residue using electronics-grade isopropyl alcohol or equivalent cleaning agents to ensure optimal circuit performance and appearance.

5. Usage Limitations

5.1 Electrical Limitations

Circuit designs must ensure conductor spacing (creepage distance) and trace width comply with safety requirements for the intended operating voltage and current, to prevent dielectric breakdown or thermal overload.

5.2 Mechanical and Environmental Limitations

  • These boards are not waterproof or heat-resistant structural components.
  • Prolonged use in humid, high-dust, corrosive-gas environments, or at temperatures exceeding the substrate's glass transition temperature (e.g., ~130°C for FR-4), is prohibited.
  • These boards must not be used as load-bearing structures or mechanical supports.
  • The tin (Sn) or tin-lead (Sn-Pb) plating is rated for a limited number of soldering cycles; repeated rework may cause pad lifting or detachment.

6. Specifications

Dimension (cm)Dimension (inch)Quantity
2 x 80.79 x 3.158 pieces
3 x 71.18 x 2.768 pieces
4 x 61.57 x 2.368 pieces
5 x 71.97 x 2.768 pieces
7 x 92.76 x 3.542 pieces

Total Quantity: 34 pieces

Board Thickness: 1.6 mm / 0.06 inch

Hole Diameter: 0.1 cm / 0.04 inch

Hole Pitch: 0.254 cm / 0.10 inch

Material: FR4 Grade Fiberglass

Detailed dimensions for each PCB board size, including hole diameter and pitch
Figure 5: Detailed dimensions for each board size, including hole pitch and thickness.

7. Maintenance

To ensure the longevity and performance of your PCB boards:

  • Cleaning: Always clean flux residue after soldering using appropriate electronic cleaning agents.
  • Storage: Store unused boards in a dry, dust-free environment, preferably in anti-static bags, to prevent oxidation and contamination.
  • Handling: Handle boards by their edges to avoid transferring oils or dirt from your skin to the copper traces.

8. Troubleshooting

While these are passive components, common issues in PCB prototyping often relate to soldering and circuit design:

  • Poor Connections: If a component isn't working, check for cold solder joints (dull, lumpy appearance) or insufficient solder. Re-solder as needed.
  • Short Circuits: Visually inspect for solder bridges between adjacent pads or traces. Use a multimeter to check for continuity where it shouldn't exist.
  • Component Damage: Ensure components are inserted correctly (polarity) and not overheated during soldering.
  • Pad Lifting: Excessive heat or prolonged soldering time can cause pads to lift. Use appropriate soldering temperatures and minimize contact time.

9. Compliance Markings

This product series complies with applicable EU regulatory requirements and meets EU health, safety, and environmental protection legislation.

  • RoHS Directive 2011/65/EU: Restriction of Hazardous Substances in Electrical and Electronic Equipment.
  • REACH Regulation (EC) No 1907/2006: Registration, Evaluation, Authorisation and Restriction of Chemicals.

10. User Tips

  • Always double-check your circuit design and component placement before soldering.
  • Test individual components before soldering them onto the board, especially if they are sensitive.
  • For complex circuits, consider using a breadboard for initial testing before committing to a permanent perfboard layout.
  • Use a fine-tip soldering iron for precise work on these boards.

11. Warranty and Support

For any questions or support regarding this product, please contact your retailer or the manufacturer directly. Please retain your proof of purchase for any warranty claims.

12. Frequently Asked Questions (FAQ)

No specific FAQs are available for this product. For general electronics prototyping questions, please consult relevant online resources or community forums.

© 2023 CHANZON. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.