Introduction
This manual provides instructions for the installation, operation, and maintenance of your SPEEDRACING 750ml Aluminum AN10 Oil Catch Can. An oil catch can is designed to collect oil vapor and sludge from the PCV/CCV system before it re-enters the engine's intake manifold. This helps to keep the engine clean, improve efficiency, and prolong engine life.
Safety & Warnings
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its components out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Handle with care to avoid cuts or injuries, especially during installation.
- This product must comply with all applicable safety and regulatory requirements in the market where it is sold.
Specifications
| Feature | Detail |
|---|---|
| Model Name | OCC-1011 |
| Special Features | Oil Catch Tank |
| Material | Aluminum Alloy |
| Capacity | 750 ml / 0.75L |
| Diameter | 76 mm (3") |
| Height | 267 mm (10.5") |
| Inlet/Outlet Size | 2x AN10 Vertically Aligned Ports |
| Item Weight | 0.7 kg |
| Applicable Models | Universal |
Package Contents
- 1 x Oil Catch Can (750ml)
- 1 x Breather Filter
- 1 x Bracket
- 1 x 3/8" Drain Valve
- 2 x AN10 Outlet/Inlet Ports
- 1 x Hose Clamp
- O-ring Gasket (for drain valve)
Setup & Installation
This oil catch can is designed for universal fitment and direct installation. Professional installation is recommended for optimal performance and safety.
- Identify Mounting Location: Choose a suitable location in your engine bay that is stable, away from extreme heat, and allows for easy access for maintenance. The included bracket can be used for mounting.
- Connect PCV/CCV Hoses: Identify the PCV (Positive Crankcase Ventilation) or CCV (Crankcase Ventilation) hose on your engine. This hose typically connects the crankcase to the intake manifold.
- Install Catch Can:
- Cut the PCV/CCV hose and connect one end to an AN10 inlet port on the catch can.
- Connect a new hose from the AN10 outlet port of the catch can to the intake manifold.
- Ensure all connections are secure and leak-free.
- Install Breather Filter: Attach the breather filter to the designated port on the top of the catch can using the provided hose clamp. This allows the crankcase to vent to the atmosphere while filtering out contaminants.
- Install Drain Valve: Screw the 3/8" drain valve into the bottom of the catch can, ensuring the O-ring gasket is properly seated to prevent oil leakage.
- Check for Clearance: Verify that the installed catch can and hoses do not interfere with any moving engine parts or other components.
Operating Instructions
Once installed, the oil catch can operates passively. It will collect oil vapor and contaminants from the engine's crankcase ventilation system. No active user input is required during operation.
Regularly monitor the level of collected fluid in the catch can to determine the appropriate maintenance schedule.
Maintenance
Regular maintenance is crucial for the effective operation of your oil catch can.
- Draining: Periodically check the oil level in the catch can. When it reaches approximately half full, or as part of your regular oil change schedule, drain the collected fluid.
- Place a suitable container under the drain valve at the bottom of the catch can.
- Open the 3/8" drain valve to allow the collected fluid to empty.
- Close the drain valve securely after draining.
- Cleaning: For thorough cleaning, especially if sludge buildup is observed:
- Remove the catch can from its mounting bracket and disconnect the hoses.
- Disassemble the breather filter and clean it with a suitable degreaser or solvent. Allow it to dry completely before reassembly.
- Clean the interior of the catch can with a degreaser. Ensure all internal baffles are free of obstruction.
- Rinse thoroughly with water and allow all components to dry completely before reinstallation.
Troubleshooting
- Oil Leakage: Check all hose connections and ensure they are tight. Verify the drain valve is fully closed and its O-ring gasket is properly seated and not damaged.
- Excessive Oil Collection / No Collection: Ensure hoses are correctly routed to and from the PCV/CCV system. Check for blockages in hoses or the catch can itself.
- Engine Performance Issues: If engine performance changes after installation, double-check all connections for vacuum leaks. Ensure the breather filter is clean and not obstructed.
User Tips
No specific user tips were available from reviews or Q&A at the time of this manual's creation. However, general tips for oil catch cans include:
- Consider using thread sealant on the AN10 fittings for an extra layer of leak prevention.
- For colder climates, check the catch can more frequently as condensation can mix with oil, potentially leading to freezing and blockages.
- Always dispose of collected oil and sludge responsibly according to local environmental regulations.
Warranty & Support
For warranty information and technical support, please contact the manufacturer:
Manufacturer: Zhejiang Xuzhong Automobile Parts Co., Ltd
Address: No. 666, Jingye Road, Economic Development Zone, Rui'an City, Wenzhou City, Zhejiang Province, China
Email: xz2014express@163.com
Telephone: +86-15888266370
You may also refer to the official user manual (PDF) for additional details and compliance information.