Hongwin 32005-21U1B

Contents

Instruction Manual

Hongwin Reverse Back Up Neutral Position Switch

Model: 32005-21U1B

Introduction

This manual provides instructions for the installation, operation, maintenance, and troubleshooting of the Hongwin Reverse Back Up Neutral Position Switch, model 32005-21U1B. This switch is designed for various Nissan vehicles, functioning as a brake lamp switch or to detect reverse/neutral gear positions.

Product Overview

The Hongwin 32005-21U1B is a 2-pin switch assembly, primarily used as a brake lamp switch. It features a durable Metal&ABS construction and a threaded body for secure mounting.

Hongwin 32005-21U1B Switch with packaging
Figure 1: Hongwin 32005-21U1B Switch with its packaging, indicating 'SWITCH ASSY-BRAKE LAMP' and '2 PIN'.

Specifications

Attribute Detail
Model Number 32005 21U1B, 3200521U1B
OEM NO. 32005-21U1B
Material Metal & ABS
Connector Type 2-Pin
Thread Size M14x1.5
Overall Length 60 mm
Body Diameter 21 mm
Hex Size 16 mm
Pin Length 8 mm
Pin Diameter 5 mm
Connector Width 11 mm
Connector Length 18 mm
Origin Mainland China
Detailed dimensions of the Hongwin 32005-21U1B switch and its 2-pin connector.
Figure 2: Detailed dimensions of the switch and connector.
Technical diagram showing M14x1.5 thread, 2-pin connector, and circuit symbol for the switch.
Figure 3: Technical diagram illustrating the M14x1.5 thread and 2-pin connector configuration.

Setup and Installation

  1. Verify Compatibility: Before installation, ensure the switch's dimensions, model type (32005-21U1B), and OEM number (32005-21U1B) match your vehicle's requirements. This switch is compatible with various Nissan models including Frontier, Xterra, Pathfinder, 240SX, Pickup, 300ZX, D21, 200SX, and Van 720.
  2. Safety First: Disconnect the vehicle's battery before beginning any electrical work to prevent accidental shorts or injury.
  3. Locate Old Switch: Identify the existing reverse, neutral position, or brake lamp switch on your vehicle. It is typically located on the transmission or brake pedal assembly.
  4. Remove Old Switch: Carefully disconnect the electrical connector from the old switch. Use an appropriate wrench (16mm hex) to unscrew and remove the old switch. Be prepared for a small amount of fluid leakage if the switch is installed in a transmission.
  5. Install New Switch: Apply a small amount of thread sealant (if recommended by your vehicle manufacturer) to the threads of the new Hongwin switch. Screw the new switch into place by hand to avoid cross-threading, then tighten with a wrench to the manufacturer's specified torque.
  6. Connect Wiring: Carefully connect the 2-pin electrical plug to the new switch. Ensure the connection is secure and the plug is fully seated. Take care not to damage the plug or wiring during this step.
  7. Reconnect Battery: Reconnect the vehicle's battery.
  8. Test Functionality: Test the switch's operation. For a reverse light switch, engage reverse gear and check if the reverse lights illuminate. For a brake lamp switch, press the brake pedal and check if the brake lights illuminate.

Operating Instructions

This switch operates automatically based on its intended function in your vehicle:

  • Reverse Light Activation: If installed as a reverse light switch, it will complete an electrical circuit when the transmission is shifted into reverse, causing the reverse lights to turn on.
  • Neutral Position Sensing: If used for neutral position sensing, it will indicate when the transmission is in neutral, which can be crucial for starting the vehicle or for specific vehicle functions.
  • Brake Lamp Activation: If functioning as a brake lamp switch, it will activate the brake lights when the brake pedal is depressed.

No manual operation is required for this component once correctly installed.

Maintenance

The Hongwin Reverse Back Up Neutral Position Switch is designed for durability and typically requires minimal maintenance. However, regular inspection can prolong its lifespan and ensure reliable operation:

  • Visual Inspection: Periodically check the switch and its wiring for any signs of physical damage, corrosion, or loose connections.
  • Cleanliness: Keep the area around the switch clean from dirt, debris, and excessive moisture, which can lead to corrosion or interfere with its operation.
  • Connection Integrity: Ensure the 2-pin connector remains firmly attached to the switch.

Troubleshooting

  • Lights Not Activating (Reverse/Brake):
    • Check the electrical connection to the switch for looseness or corrosion.
    • Inspect the wiring harness for any cuts or damage.
    • Verify that the bulbs for the respective lights are functional.
    • Test the switch for continuity using a multimeter. Determine if the contact is normally open or normally closed for your specific application and test accordingly.
    • Ensure the switch is fully depressed or released as required by its function.
  • Intermittent Operation:
    • This could indicate a loose connection, internal wear of the switch, or intermittent wiring issues. Re-check connections and consider replacing the switch if issues persist.

User Tips

  • Always double-check the dimensions and model type against your vehicle's specifications before purchasing and installing to ensure proper fit and function.
  • Handle the electrical plug with care during installation and removal to prevent damage to the pins or wiring.
  • If the switch does not work after installation, re-verify all connections and ensure it is the correct part for your vehicle's specific year, make, and model.

Warranty and Support

For product support, warranty information, or inquiries, please contact the manufacturer or their authorized representative:

  • Brand: Hongwin
  • Manufacturer: Wenzhou Haowei Auto Parts Co., Ltd.
  • Manufacturer Address: Floor 2, Building 8 (West), Hantian Hardware and Electrical City, Tangxia Town, Ruian City, Zhejiang Province, China
  • Customer Service Email: inf@hwautoparts.com
  • Customer Service Tel: 86-18005775583
  • EU Representative: MJCM SARL
  • EU Representative Address: CN-78 avenue des Champs Elysees Bureau 326
  • EU Representative Tel: 33-767213611
  • EU Representative E-mail: mjcm190928@gmail.com

A detailed user manual in PDF format is also available for download. Please refer to the official product page or contact support for the link.

Environmental Information

Please dispose of packaging materials responsibly. Follow local regulations for recycling and waste management. The packaging elements should be separated and deposited in the appropriate recycling bins.

WARNING: To avoid danger of suffocation, keep this plastic bag away from babies and children. Do not use this bag in cribs, beds, carriages, or play pens. This bag is not a toy.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.