STEPPERONLINE MG17-G5/G10/G20/G50/G100

Contents

Nema 17 Planetary Gearbox Motor Speed Reducer

Model: MG17-G5/G10/G20/G50/G100

Brand: STEPPERONLINE

1. Introduction

This manual provides instructions for the installation, operation, and maintenance of the STEPPERONLINE Nema 17 Planetary Gearbox Motor Speed Reducer. This gearbox is designed to be coupled with Nema 17 stepper motors, offering various gear ratios to achieve desired speed reduction and torque multiplication for a wide range of applications.

Nema 17 Planetary Gearbox, front-side view

Figure 1: Nema 17 Planetary Gearbox

2. Safety Information

Please read and understand all safety precautions before installing or operating the gearbox. Failure to do so may result in personal injury or damage to the equipment.

  • Ensure the power to the stepper motor is disconnected before any installation or maintenance work.
  • Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves.
  • Avoid touching moving parts during operation.
  • Do not exceed the maximum permissible torque or input speed specified for your gearbox model.
  • Ensure proper ventilation to prevent overheating, especially during continuous operation at high loads.
  • The gearbox operates within a temperature range of -20°C to 150°C. Do not operate outside this range.

3. Package Contents

Verify that all items are present and undamaged upon opening the package. If any items are missing or damaged, contact your supplier immediately.

  • 1 x Nema 17 Planetary Gearbox (specific ratio as ordered)
  • Mounting screws (typically 4 hex socket head screws)
  • Key for output shaft (if applicable to your model)
  • User Manual (this document, or a PDF version)
Mounting hardware for the gearbox

Figure 2: Typical Mounting Hardware

Product packaging showing two gearboxes in foam inserts

Figure 3: Example of Product Packaging

4. Setup and Installation

Follow these steps to properly install the planetary gearbox onto your Nema 17 stepper motor:

  1. Prepare the Motor: Ensure your Nema 17 stepper motor has an input shaft diameter of 5mm and a length between 6.5mm and 10.5mm to properly engage with the gearbox.
  2. Align the Shafts: Carefully align the input shaft of the gearbox with the shaft of your Nema 17 stepper motor. The gearbox features a clamping mechanism (collet) to secure the motor shaft.
  3. Mount the Motor: Position the stepper motor against the gearbox's mounting face. The gearbox has a standard Nema 17 mounting pattern (42x42mm).
  4. Secure the Motor: Use the provided mounting screws to firmly attach the stepper motor to the gearbox. Ensure the screws are tightened evenly to prevent misalignment or stress on the components.
  5. Check for Engagement: After mounting, manually rotate the output shaft of the gearbox to ensure smooth operation and proper engagement with the motor. There should be no binding or excessive play.
Planetary gearbox mounted on a Nema 17 stepper motor, side view

Figure 4: Gearbox Mounted on a Stepper Motor

Planetary gearbox mounted on a Nema 17 stepper motor, top view

Figure 5: Top View of Mounted Gearbox

5. Operating Instructions

Once the gearbox is securely installed, you can operate the stepper motor as usual. The gearbox will reduce the motor's output speed and increase its torque according to the selected gear ratio.

  • Initial Test: Start with low speeds and loads to verify proper function.
  • Load Considerations: Do not exceed the maximum permissible torque for your specific gearbox ratio. Overloading can lead to premature wear or damage.
  • Speed Limits: Adhere to the rated and maximum input speeds to ensure optimal performance and longevity.
  • Noise: The gearbox is designed for low noise operation (typically <=55 dB). Unusual noises may indicate an issue.

6. Maintenance

The planetary gearbox is designed for long-term, maintenance-free operation under normal conditions. However, periodic checks are recommended:

  • Inspection: Periodically inspect the gearbox for any signs of wear, damage, or loose connections.
  • Cleaning: Keep the exterior of the gearbox clean and free from dust, debris, or corrosive substances.
  • Lubrication: The gearbox is pre-lubricated and sealed. No additional lubrication is required under normal operating conditions. Do not attempt to open the gearbox for lubrication, as this may void the warranty and compromise its IP54 rating.
  • Temperature Monitoring: Ensure the operating temperature remains within the specified range. Excessive heat can indicate overloading or other issues.

7. Troubleshooting

Problem Possible Cause Solution
Excessive noise or vibration
  • Misalignment between motor and gearbox
  • Loose mounting screws
  • Overload condition
  • Internal damage
  • Re-align motor and gearbox
  • Tighten all mounting screws
  • Reduce load or check motor sizing
  • Contact support if internal damage is suspected
Gearbox overheating
  • Continuous operation at high load
  • Insufficient ventilation
  • Exceeding maximum input speed
  • Reduce load or operating time
  • Ensure adequate airflow around the gearbox
  • Verify input speed is within limits
Output shaft does not rotate or slips
  • Motor shaft not properly secured
  • Internal gear damage
  • Excessive load
  • Re-secure motor shaft in the gearbox collet
  • Reduce load
  • Contact support

8. User Tips

  • Inspect Packaging: Upon receiving your gearbox, carefully inspect the packaging for any signs of damage. The product is typically well-packaged, but checking for external damage can prevent issues.
  • Verify Contents: Confirm all components listed in the 'Package Contents' section are present and in good condition before beginning installation.
  • Backlash: Be aware of the backlash specification (e.g., <=30 arcmin for G5/G10, <=45 arcmin for G20/G50/G100). This is the amount of play in the gears and is normal within specified limits.
  • Gear Material: The gears within these planetary gearboxes are typically made of hardened steel for durability and high torque capacity.
  • Shaft Dimensions: The gearbox is designed for Nema 17 motors with a 5mm input shaft. The gearbox output shaft diameter is 8mm for G5/G10 models and 10mm for G20/G50/G100 models.

9. Specifications

The following table outlines the general specifications for the Nema 17 Planetary Gearbox. Specific values may vary slightly depending on the gear ratio (G5, G10, G20, G50, G100).

Specification Value
BrandSTEPPERONLINE
Model NumberMG17-G5/G10/G20/G50/G100
CertificationCE
OriginMainland China
Gear Ratios Available5:1, 10:1, 20:1, 50:1, 100:1
Gearbox Matching Motor's Input Shaft Length6.5-10.5 mm
Gearbox Input Bore DiameterØ5 mm (for Nema 17 motor shaft)
Output Shaft TypeKey way
Rated Input Speed1000 RPM
Max. Input Speed2000 RPM
Shaft Maximum Axial Load100 N
Shaft Maximum Radial Load300 N
Noise<=55 dB
Waterproof RatingIP54
Working Temperature-20°C ~ 150°C (-4°F ~ 302°F)

9.1. Ratio-Specific Specifications

Specification G5 (5:1) G10 (10:1) G20 (20:1) G50 (50:1) G100 (100:1)
Efficiency90.00%90.00%80.00%80.00%80.00%
Backlash@No-Load (arcmin)<=30<=30<=45<=45<=45
Max. Permissible Torque (Nm [lb-in])9.00 [79.66]5.00 [44.25]5.00 [44.25]5.00 [44.25]5.00 [44.25]
Output Shaft DiameterØ8 mmØ8 mmØ10 mmØ10 mmØ10 mm

9.2. Dimensional Drawings

Detailed dimensional drawings for each gearbox model are provided below. These diagrams include critical measurements for integration into your projects.

Dimensional drawing for MG17-G5 Planetary Gearbox

Figure 6: MG17-G5 Dimensions and Specifications

Dimensional drawing for MG17-G10 Planetary Gearbox

Figure 7: MG17-G10 Dimensions and Specifications

Dimensional drawing for MG17-G20 Planetary Gearbox

Figure 8: MG17-G20 Dimensions and Specifications

Dimensional drawing for MG17-G50 Planetary Gearbox

Figure 9: MG17-G50 Dimensions and Specifications

Dimensional drawing for MG17-G100 Planetary Gearbox

Figure 10: MG17-G100 Dimensions and Specifications

For a complete user manual in PDF format, please refer to the official documentation: User Manual (PDF).

10. Warranty and Support

For warranty information, technical support, or any inquiries regarding your STEPPERONLINE Planetary Gearbox, please contact the seller or manufacturer directly. Ensure you have your product model number and purchase details available when seeking support.

© 2024 STEPPERONLINE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.