CPVAN PIR Motion Sensor Wireless Motion Detector
User Instruction Manual
1. Introduction
This device is a wireless motion detector equipped with a Passive Infrared (PIR) sensor, designed to enhance your home security system. It can effectively monitor an area with a detection radius of up to 12 meters and features pet immunity to prevent false alarms from small animals. The detector connects to your wireless security system using the eV1527 protocol, offering an effective communication range of up to 100 meters in open areas without obstacles. Powered by a single CR2450 3V lithium battery, it can operate for up to 2 years and is intended for indoor use only.
Figure 1: Front view of the CPVAN PIR Motion Sensor.
2. In the Box
Please check the package contents to ensure all items are present:
- PIR Detector (with pre-installed CR2450 battery) x1
- Bracket x1
- Screws x2
- Switch Toggle Tool x1
- Quick Start Guide x1
3. Product Overview (At a Glance)
Familiarize yourself with the components and controls of your PIR Motion Detector:
- Mounting strip: Used for attaching the detector to the bracket.
- Bracket: Provides a secure base for mounting the detector.
- Battery receptacle: Houses the CR2450 3V lithium battery.
- CR2450 3V lithium battery: Powers the device.
- Motion detect lens: The primary component for detecting infrared changes caused by movement.
- Light indicator: Located inside the detector. It blinks for 30 seconds after the detector powers on, lights up when motion is detected, and blinks continuously to indicate a low battery. Replace the battery promptly when this occurs.
The detector features two switches on its back, accessible with the included toggling tool:
- Power on/off switch: Slide to 'ON' to power up the detector.
- TEST & NORMAL switch:
- NORMAL mode: Designed to save battery power. If motion is triggered twice within 3 minutes, the detector enters a sleeping state, and subsequent movements will not generate an alarm for a short period. After 3 minutes of no movement, it returns to its active working state.
- TEST mode: For effective walk testing of the detection area.
- Always slide the switch to 'NORM' after testing to conserve battery life.
4. Installation
4.1 Detector Location
Careful selection of the installation location is crucial for optimal performance and to avoid false alarms. Consider the lens direction and ensure no obstacles impair the view or radio signal transmission.
- Do not install the PIR Motion Detector outdoors, in a garage, or directly on glass surfaces, as it cannot detect motion through glass.
- Avoid places where the detector could get wet, such as near swing-out windows that may be exposed to rain.
- Do not install the detector within 3 feet (1 meter) of heat sources like electric heaters, heat vents, fireplaces, or any other source that may produce turbulent air, as these can cause false triggers.
- Ensure the detector is not placed behind large appliances or furniture that could obstruct its motion sensors.
Figure 2: Motion detection range diagram (110 degrees, up to 12 meters).
Figure 3: The detector is designed to ignore pets weighing under 15 kg.
4.2 Mounting the Detector
The motion detector should be mounted at a height of 79 to 87 inches (2 to 2.2 meters) above the floor for optimal detection. Use the included screws to securely mount the bracket to your chosen wall. Once the bracket is in place, simply attach the motion detector to the bracket. After mounting, perform a walk test (see Section 3 for TEST mode) to confirm the detection range and coverage.
Figure 4: Side view of the detector showing mounting bracket attachment.
5. Setup and Pairing with a Security System
The CPVAN PIR Motion Sensor is designed to integrate with compatible wireless security systems. The general pairing process involves adding the device through your security system's mobile application or control panel.
General Pairing Steps:
- Ensure your security system's control panel is powered on and connected to your network (Wi-Fi).
- Open the associated mobile application (e.g., Smart Life APP) on your smartphone.
- Navigate to the 'Add Device' or 'Accessories' section within the app.
- Select the category for 'Security & Sensor' and then 'Alarm' or 'Motion Sensor'.
- Follow the on-screen prompts to put your security system into pairing mode (often referred to as 'Smartlink Mode' or 'Add accessory').
- Power on your PIR Motion Sensor. If prompted, reset the device or confirm that its indicator light is blinking rapidly, indicating it's ready for pairing.
- Once the app confirms 'Configuration OK' or 'Added successfully', the PIR sensor is paired.
- Repeat similar steps to add other accessories like sirens, door sensors, or remote controls by triggering them while the system is in 'Add accessory' mode.
Video 1: Demonstration of adding accessories, including a PIR sensor, to a security system via a mobile application.
6. Operation
Once installed and paired, the PIR Motion Sensor operates as part of your security system:
- Arming/Disarming: Use your security system's control panel, mobile app, or remote controls to arm or disarm the system. The PIR sensor will only detect motion and trigger an alarm when the system is armed.
- Motion Detection: When armed, the sensor detects infrared changes caused by movement within its detection scope.
- Pet Immunity: The sensor is designed to ignore pets weighing under 15 kg, minimizing false alarms.
- TEST Mode: Use this mode during installation or troubleshooting to verify the sensor's detection capabilities.
- NORMAL Mode: This is the standard operating mode, which includes power-saving features.
Figure 5: Key features of the Wireless Pet-Immune PIR Motion Sensor.
7. Maintenance
- Battery Replacement: When the internal light indicator blinks, it signifies a low battery. Replace the CR2450 3V lithium battery promptly to ensure continuous operation.
- Cleaning: Periodically clean the motion detect lens with a soft, dry cloth to ensure clear detection and prevent dust buildup from affecting performance.
8. Troubleshooting
- False Alarms:
- Check for heat sources (heaters, vents, direct sunlight) or turbulent air currents near the detector.
- Ensure no large objects or furniture are obstructing the sensor's view.
- Verify that pets are within the specified weight limit (under 15 kg) for pet immunity.
- No Detection:
- Confirm the detector is powered ON and the battery is not low.
- Ensure the sensor has a clear line of sight to the monitored area.
- Perform a walk test in TEST mode to confirm the sensor's functionality.
- Check the connection and pairing status with your security system.
- Poor Wireless Range:
- Minimize major obstacles (e.g., thick walls, metal objects) between the detector and the security system's control panel.
- Ensure the detector is within the effective communication range (up to 100m in open areas).
9. User Tips
- Optimizing Pet Immunity: While the detector has built-in pet immunity, for households with particularly active pets or those close to the weight limit, consider utilizing the 'NORMAL' mode's power-saving feature. This mode allows for multiple triggers before entering a temporary sleep state, which can help reduce false alarms from repeated minor pet movements.
- Regular Testing: Periodically test your motion sensor using the 'TEST' mode to ensure it is functioning correctly and its detection range is still optimal for your environment.
10. Specifications
| Feature | Specification |
|---|---|
| Power Supply | DC 3V (CR2450 Lithium Battery x1) |
| Standby Current | <15uA |
| Alarm Current | <25mA |
| Detection Scope | <12m / 110° |
| Transmitting Distance | <100m (Open Area and No Interference) |
| Radio Frequency | 433Mhz |
| Operation Temperature | -10~55°C |
11. Support
For further assistance, technical support, or warranty information, please contact the seller or refer to the comprehensive user manual available as a PDF document. You can access the PDF manual for more detailed instructions and diagrams: CPVAN PIR Motion Sensor User Manual (PDF).