1. Introduction
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your new AUTOXBERT Heated Convex Wing Mirror Glass. This product is designed to replace the original wing mirror glass on specific Land Rover models, enhancing driving safety by providing clear rear and side visibility.
For model-specific guidance, always refer to your vehicle's owner's manual. If you are unsure about any part of the installation or operation, consult a professional mechanic.
A comprehensive user manual in PDF format is available for download: User Manual (PDF).
2. Product Information
The AUTOXBERT Heated Convex Wing Mirror Glass is a direct replacement part for the following vehicles:
- Land Rover Discovery 3 (2004-2009)
- Land Rover Range Rover Sport L320 (2005-2009)
- Land Rover Range Rover Vogue (2005-2009)
- Land Rover Freelander 2 FA_ (2006-2009) SUV
Note: This product is NOT suitable for:
- Land Rover Range Rover Vogue MK3 (2002 - 2004) and (2010 - 2012)
- Land Rover Range Rover Sport (2010-2013)
2.1. Specifications
| Feature | Detail |
|---|---|
| Brand | AUTOXBERT |
| Model (OEM No.) | LR017070 (Left), LR017067 (Right) |
| Item Type | Mirror & Covers |
| Material | ABS & Glass |
| Glass Type | Convex, Heated |
| Placement | Front Left / Right Side |
| Color | Silver / Clear |
| Item Weight | 0.2kg |
| External Testing Certification | ISO9001 |
| Origin | Mainland China |
| Dimensions | Approx. 14cm (5.51in) x 20cm (7.87in) |
3. Safety & Warnings
Important Safety Information: Read all instructions before use.
- Inspect the product before each use; do not use if damaged (such as cracked mirror glass, broken housing, loose brackets or damaged wires).
- Disconnect the vehicle power supply before installation to avoid electric shock or short circuit (for electric wing mirrors).
- Install the wing mirror in strict accordance with the instructions; improper installation may cause the mirror to fall off during driving, leading to traffic accidents.
- Keep the product away from high temperature, open flame and humid environment to avoid damage to the mirror glass, housing and internal electrical components (if applicable).
- Do not modify the product structure, brackets or wires without authorization, otherwise it may cause product failure or safety hazards.
- Do not touch the mirror glass with sharp objects to prevent scratches; do not strike the mirror forcefully to avoid glass breakage and personal injury.
4. Preparation
4.1. Tools & Materials Needed
- New car wing mirror glass (ensure the model and size match your vehicle; check the bracket type, mirror type (manual/electric) and interface specifications according to the vehicle model).
- Soft cloth (to clean the installation position and mirror surface).
- Screwdriver (crosshead/flathead, according to the vehicle's mirror fixing method).
- Wrench (adjustable wrench, for tightening nuts and bolts).
- Insulating tape (to protect the connection part of the wires and prevent short circuit, for electric wing mirrors).
- Adhesive tape (optional, for auxiliary fixing during installation).
4.2. Safety Precautions Before Installation
- Park the vehicle on a flat surface, turn off the engine, and engage the parking brake.
- Disconnect the vehicle battery or turn off the corresponding power switch to avoid electric shock during installation (for electric wing mirrors).
- Avoid touching the mirror glass and sharp edges of the bracket with your hands to prevent scratches and cuts.
- Ensure that the installation position is dry and clean, and there is no oil stain, dust or water stain to avoid affecting the installation firmness and service life.
- Ask for assistance if necessary during installation to avoid accidental falling of the mirror and personal injury or product damage.
5. Installation Instructions
5.1. Step 1: Remove the Old Wing Mirror
- Confirm power is off: Double-check that the vehicle power supply corresponding to the wing mirror to be replaced is turned off (for electric models) to avoid short circuit.
- Remove the interior trim panel: Locate the trim panel inside the vehicle door corresponding to the wing mirror. Gently pry open the trim panel with a screwdriver (wrap the screwdriver head with a soft cloth to avoid scratching the trim) to expose the fixing screws and wire connector (for electric models).
- Disconnect the wire connector (for electric wing mirrors): Align the screwdriver with the buckle of the wire connector, gently pry it open, and disconnect the wire (pay attention to the wire position and connection method to facilitate subsequent installation).
- Remove the fixing screws: Use a screwdriver to unscrew the screws that fix the wing mirror bracket to the door (usually 2-3 screws), and place the screws in a clean place to avoid loss.
- Take out the old wing mirror: Gently pull the old wing mirror outward to separate it from the door, and take it out completely. Dispose of the old mirror properly; do not discard it at will, and handle it according to environmental protection requirements (especially broken mirror glass).
5.2. Step 2: Install the New Wing Mirror
- Check the new wing mirror: Confirm that the model, bracket type and mirror type (manual/electric) of the new wing mirror match the vehicle, and check that the mirror glass, housing, bracket and wires (if applicable) are intact.
- Connect the wire connector (for electric wing mirrors): Align the wire connector of the new wing mirror with the vehicle's wire connector, and insert it firmly (pay attention to the positive and negative poles; if the mirror cannot be adjusted normally after installation, it may be that the positive and negative poles are reversed, and you can adjust the connector direction).
- Install the wing mirror bracket: Align the bracket of the new wing mirror with the installation hole on the door, gently push the mirror inward to fit it closely with the door, and ensure that the screw holes of the bracket are aligned with the installation holes on the door.
- Tighten the fixing screws: Insert the reserved screws into the screw holes, and use a screwdriver to tighten them gently (do not over-tighten to avoid damaging the bracket or door). Check that the bracket is firmly fixed and does not shake.
- Reset the interior trim panel: Align the interior trim panel with the installation position, press it gently until it clicks into place, and ensure that the trim panel is closely fitted with the door and does not loosen.
5.3. Step 3: Remove Protective Film
Tear off the protective film on the surface of the new wing mirror glass and housing to ensure the mirror's viewing effect and appearance.
6. Operation and Adjustment
6.1. Adjust the Mirror Angle
- For manual wing mirrors: Adjust the mirror angle by hand gently, ensuring that the driver can clearly observe the rear and side road conditions when sitting in the driving position.
- For electric wing mirrors: Reconnect the vehicle battery, turn on the vehicle power, and use the mirror adjustment switch inside the vehicle to adjust the upper, lower, left and right angles of the mirror until the best viewing effect is achieved.
6.2. Testing & Adjustment
- Restore the power supply: Reconnect the vehicle battery or turn on the corresponding power switch (for electric wing mirrors).
- Test functionality:
- Test mirror adjustment: For electric models, use the adjustment switch to check if the mirror can move freely up, down, left and right, and if the adjustment is smooth without jamming.
- Test mirror stability: Shake the wing mirror gently by hand to check if it is firmly fixed, without looseness or shaking.
- Test viewing effect: Sit in the driving position, check if the mirror can clearly reflect the rear and side road conditions, and adjust the angle again if necessary.
- Check for abnormalities: For electric models, listen for unusual noises (such as sizzling sound) during adjustment, and check if the mirror housing is overheated. If any abnormality is found, turn off the power immediately, check the wire connection and installation position, and troubleshoot the problem.
7. Maintenance Tips
- Clean regularly: Wipe the mirror surface and housing with a damp soft cloth every month to remove dirt, dust and oil stains, so as not to affect the viewing effect. For stubborn stains, you can use a small amount of neutral detergent to clean, and then wipe dry with a soft cloth.
- Check regularly: Check the installation firmness of the wing mirror, the tightness of the screws and the wire connection (for electric models) every 3 months. If loose or falling off is found, fix it in time.
- Replace when necessary: If the mirror glass is cracked, the housing is damaged, or the electric mirror cannot be adjusted normally (after troubleshooting), replace it in time; replace it with the same model and specification of wing mirror.
- Waterproof protection: Avoid washing the car with high-pressure water directly facing the wing mirror connection part to prevent water from entering and causing short circuit (for electric models); if water enters accidentally, turn off the power immediately and dry it before use.
- Winter maintenance: In cold weather, do not scrape the ice on the mirror glass with sharp objects; you can use warm water (not boiling water) to melt the ice to avoid glass breakage.
8. Troubleshooting Common Issues
| Issue | Solution |
|---|---|
| Electric wing mirror cannot be adjusted | Verify the positive and negative poles of the wire connection are correct; check if the wire connector is loose or disconnected; check if the vehicle power supply is normal; check if the adjustment switch is faulty; replace the wing mirror if it is damaged. |
| Wing mirror is loose or shakes during driving | Check if the fixing screws are loose and tighten them in time; check if the bracket is damaged; replace the bracket or wing mirror if necessary. |
| Mirror glass is blurred or has poor visibility | Clean the mirror surface with a soft cloth and neutral detergent; check if the mirror glass is scratched; replace the mirror glass if necessary. |
| Mirror glass is broken | Replace the mirror glass or the entire wing mirror in time; handle the broken glass carefully to avoid personal injury. |
| Water enters the wing mirror housing | Turn off the power immediately (for electric models); disassemble the mirror and dry the internal components; check if the housing is cracked or the seal is damaged; replace the housing or wing mirror if necessary. |
9. User Tips
- Ensure you select the correct mirror (driver or passenger side) for your vehicle to ensure proper fitment and functionality.
- This mirror is designed for door mounting and features heating functionality, which can be particularly useful in cold weather conditions to prevent ice buildup.
10. Warranty and Support
For warranty information, please refer to the product packaging or contact the seller directly. For technical support or further assistance, please reach out to the manufacturer at info@yiyasu.com or the EU representative at lefeng.tech@outlook.com.