Ziqqucu Microphone Amplifier Board

Contents

Microphone Amplifier Board User Manual

Model: Microphone Amplifier Board

Brand: Ziqqucu

1. Introduction

This manual provides detailed instructions for the Ziqqucu Microphone Amplifier Board. This specialized amplifier is designed for electret microphones, utilizing 48V phantom power. It is compatible with both omnidirectional and unidirectional electret microphones, making it suitable for various audio applications such as karaoke, recording, and conference speech.

For additional documentation, a user manual in PDF format is available here.

2. Product Overview

The amplifier board is a compact module designed to boost the signal from electret condenser microphones. It requires external 15-48V phantom power for operation, which is typically supplied by a mixer, audio interface, or dedicated phantom power supply.

Microphone Amplifier Board with 2-pin connector

Figure 1: Ziqqucu Microphone Amplifier Board with 2-pin output connector. The inset shows the pin configuration.

3. Setup and Connection

Proper connection is crucial for optimal performance. This board is designed specifically for electret microphones.

3.1. Components

  • Microphone Amplifier Board
  • Electret Condenser Microphone (low-noise recommended)
  • Audio cable with appropriate connectors (e.g., XLR)
  • 48V Phantom Power source (mixer, audio interface, or dedicated supply)

3.2. Connection Steps

  1. Connect Electret Microphone: Solder or connect your electret microphone to the designated "MIC" input pads on the amplifier board. Ensure correct polarity if your microphone requires it (typically, the microphone's positive terminal connects to the "+" pad and negative/ground to the "-" pad, or as per microphone datasheet).
  2. Connect Output: The amplifier board features a 2-pin output connector. This connector will typically be wired to an XLR male connector for standard audio equipment.
    Top view of amplifier board showing MIC input pads

    Figure 2: Top view of the amplifier board, showing "MIC" input pads and component layout.

    The 2-pin output connector on the board (as shown in Figure 1) typically corresponds to the balanced output of an XLR cable, where one pin carries the positive signal, the other the negative signal, and the shield/ground is connected separately (often to the board's ground plane or the XLR shell).

  3. Apply Phantom Power: Connect the XLR output from the amplifier board to your mixer or audio interface. Activate the 48V phantom power on your device. The amplifier board draws its power from this phantom power supply.

Important: The noise performance of the amplifier board is significantly influenced by the quality of the electret microphone. For best results, use a low-noise electret microphone.

4. Operating Instructions

Once properly connected and powered, the amplifier board will amplify the signal from your electret microphone. No user adjustments are required on the board itself.

  1. Ensure all connections are secure and phantom power is active.
  2. Adjust input gain on your mixer or audio interface to achieve desired recording levels without clipping.
  3. Monitor audio output to confirm proper operation.
Example setup of a parabolic microphone with recording equipment

Figure 3: Example application of a microphone setup, potentially utilizing an amplifier board like this one, for specialized audio capture.

5. Maintenance

The Microphone Amplifier Board is a robust electronic component. Follow these guidelines for longevity:

  • Keep the board dry and away from moisture.
  • Avoid exposing the board to extreme temperatures.
  • Handle with care to prevent physical damage to components or solder joints.
  • Clean gently with a dry, soft brush if dust accumulates. Do not use liquids or solvents.
  • Avoid static discharge when handling the board.

6. Troubleshooting

6.1. No Sound Output

  • Check Phantom Power: Ensure 48V phantom power is enabled on your mixer/interface.
  • Verify Connections: Double-check all wiring from the electret microphone to the board, and from the board's output to your audio equipment.
  • Test Microphone: Ensure your electret microphone is functional.
  • Check Cables: Inspect audio cables for damage or faulty connectors.

6.2. High Noise or Hum

  • Microphone Quality: As recommended, use a low-noise electret microphone.
  • Grounding: Ensure proper grounding throughout your audio chain to avoid ground loops.
  • Interference: Keep the board and cables away from sources of electromagnetic interference (e.g., power supplies, motors).

6.3. Distorted Audio

  • Input Level: Ensure the microphone's sound pressure level (SPL) does not exceed the board's capabilities (125dB max).
  • Gain Staging: Adjust gain levels on your mixer/interface to prevent clipping.

7. Specifications

FeatureSpecification
Microphone TypeElectret Condenser Microphone
Power Supply15-48V Phantom Power
Working CurrentApproximately 3.2mA
Output Impedance250 ohms
Max Sound Pressure Level (SPL)125dB
Signal-to-Noise Ratio (SNR)60dB
Board Dimensions45mm x 15.82mm (excluding connector)

8. User Tips

  • Microphone Capsules: Users have reported good results with AOM-5024L-HD-R and Primo 272 Z1 capsules.
  • Wiring Standards: Consider using NOGAMI wiring standards for custom microphone builds.
  • Compatibility: This amplifier board is designed for electret condenser microphones only. It is NOT compatible with dynamic microphones.
  • Recording Devices: The board has been successfully used with recorders like the ZOOM Z6.

9. Warranty and Support

For any issues, technical support, or warranty inquiries, please contact your seller or the manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.