Engineer SS-02

Contents

Engineer SS-02/SS-03 Solder Sucker Instruction Manual

Manual Desoldering Pump for SMT and IC Component Removal

1. Introduction

Thank you for choosing the Engineer SS-02/SS-03 Solder Sucker. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your desoldering pump. Please read this manual thoroughly before first use and keep it for future reference.

2. Safety Precautions

  • Always wear appropriate eye protection when soldering or desoldering.
  • Ensure adequate ventilation in your workspace to avoid inhaling solder fumes.
  • The solder sucker nozzle will come into contact with hot solder and can become hot. Handle with care.
  • Keep out of reach of children.

3. Product Overview

The Engineer Solder Sucker is a compact, high-power manual desoldering pump designed for efficient removal of molten solder from circuit boards. It features a durable body and a heat-resistant silicone nozzle for effective one-hand operation.

Engineer SS-02 Solder Sucker
Figure 1: Engineer SS-02 Solder Sucker (Silver, 50mm Sucker Tube variant)
Solder Sucker with labeled parts
Figure 2: Key components of the Solder Sucker. Red arrow points to the Operation Button, white arrow points to the Reset Button. The body is labeled 'Made in Japan'.

4. Setup

  1. Unpack: Carefully remove the solder sucker from its packaging.
  2. Inspect: Check the device for any visible damage. Ensure the silicone nozzle is securely attached to the tip.
  3. Prime: Before first use, push the plunger rod all the way down until it locks. Then, press the reset button (the small button on the side) to release the plunger. This confirms the mechanism is working correctly.

5. Operating Instructions

Follow these steps for effective desoldering:

  1. Prepare the Pump: Push the plunger rod down until it clicks and locks into place. The pump is now cocked and ready for suction.
  2. Heat the Solder Joint: Using a heated soldering iron, apply heat to the solder joint you wish to desolder until the solder becomes fully molten.
  3. Position the Nozzle: While the solder is still molten, quickly place the silicone nozzle of the solder sucker directly over the molten solder joint, ensuring a good seal with the PCB. The silicone nozzle adheres closely to the board for optimal suction.
  4. Activate Suction: Press the operation button (the red button at the top of the plunger rod) firmly. The plunger will retract rapidly, creating a vacuum that sucks the molten solder into the pump's chamber.
  5. Remove and Inspect: Remove the solder sucker and soldering iron. Inspect the desoldered joint. If any solder remains, repeat steps 2-4.
Solder sucker in action
Figure 3: Proper technique for using the solder sucker to remove solder from a component lead.
Silicone nozzle on PCB with high suction
Figure 4: The silicone nozzle creates a tight seal on the PCB, enabling high suction power for clean solder absorption.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your solder sucker.

  1. Emptying Solder: After several uses, the chamber will fill with solder. To empty, unscrew the nozzle assembly or the rear cap (depending on model design) and tap out the accumulated solder.
  2. Cleaning the Nozzle: Periodically clean the silicone nozzle to remove any residual solder or flux buildup. This can be done with a small brush or by gently scraping with a non-abrasive tool.
  3. Replacing the Silicone Nozzle: The silicone nozzle is a consumable part and may wear out or get damaged over time. Replace it with genuine Engineer spare parts (e.g., SS-16 Silicone Tube for SS-02).
Engineer SS-16 Silicone Tube for SS-02
Figure 5: Replacement silicone tubes (SS-16) for the Engineer SS-02 solder sucker.

7. Troubleshooting

ProblemPossible CauseSolution
Low or no suctionNozzle clogged with solder; Poor seal on PCB; Plunger not fully cocked; Internal seal issue.Clean nozzle; Ensure nozzle is flush with PCB; Re-cock plunger; Disassemble and clean internal components if possible.
Solder not fully removedSolder not fully molten; Insufficient heat; Quick removal of iron before suction.Ensure solder is fully liquid; Use appropriate soldering iron temperature; Keep iron on joint until suction is applied.
Nozzle damaged/wornNormal wear and tear; Contact with sharp objects.Replace with a new silicone nozzle (e.g., Engineer SS-16).

8. Specifications

FeatureDetail
ModelSS-02 (also available as SS-03)
BrandEngineer
OriginJapan
CertificationCE
Nozzle MaterialHeat-resistant Silicone
Nozzle Heat Resistance<350°C
Overall Length153 mm
Body Diameter20 mm
Nozzle Tip DiameterInner Ø2 mm, Outer Ø4 mm
FeaturesCompact body, High-power absorption, One-hand operation
Engineer Solder Sucker Dimensions Diagram
Figure 6: Dimensional drawing of the Engineer Solder Sucker (measurements in mm).

9. User Tips

  • Always ensure the solder is fully molten and shiny before attempting to desolder. Cold joints will not desolder effectively.
  • Place the nozzle as flush as possible against the PCB and component lead to create the best vacuum seal.
  • Practice on scrap circuit boards to get a feel for the timing and technique before working on critical components.
  • Regularly clean the nozzle and empty the solder chamber to maintain consistent suction power.

10. Warranty and Support

For any questions, technical support, or warranty claims, please contact your original seller or authorized distributor. Please have your purchase details ready when contacting support.

© 2023 Engineer Co., Ltd. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.