CNC Z50

Contents

CNC Silver Front & Rear Disc Brake Hub User Manual

For Dax, Ruckus, Zoomer, Monkey Z50 Bikes

Introduction

This manual provides detailed instructions for the installation, maintenance, and troubleshooting of your new CNC Silver Front & Rear Disc Brake Hubs. These hubs are designed for Dax, Ruckus, Zoomer, and Monkey Z50 bikes, offering enhanced braking performance and durability. Please read this manual thoroughly before installation to ensure proper function and safety.

Specifications

Feature Detail
Model Name Z50
Material Alloy (CNC Machined)
Origin Mainland China
Rim Size Compatibility 8 inch (3.50-8), universal for front and rear
Front Hub Structure Without flange
Rear Hub Structure Equipped with flange and studs
Bearings & Oil Seals 6202 bearings & unified oil seal specifications
Axle Diameter 12mm (approximate, based on diagrams)
Bolt Circle Diameter 64mm (approximate, based on diagrams)
Front and Rear Wheel Hub with key dimensions
Figure 1: Front and Rear Wheel Hubs with key dimensions (12mm axle, 64mm bolt circle).
Rear Wheel Hub with 57mm measurement
Figure 2: Rear Wheel Hub showing 57mm measurement.
Front Wheel Hub with 57mm measurement
Figure 3: Front Wheel Hub showing 57mm measurement.

Safety Information

Always wear appropriate personal protective equipment (PPE) such as safety glasses and gloves when performing installation or maintenance. Ensure the vehicle is stable and securely supported before beginning any work. If you are unsure about any step, consult a qualified mechanic.

Tools Required

  • 17mm, 14mm, and 12mm Socket Wrenches
  • Bearing Puller
  • Copper Rod & Hammer
  • High-temperature Grease
  • Sealant
  • Torque Wrench
  • Parking Bracket
  • Jack
  • Tire Lever

Installation Instructions

Front Wheel Hub Installation

3.1 Old Hub Removal

  1. Lift the vehicle to keep the front wheel off the ground.
  2. Loosen the brake cable.
  3. Remove the 17mm axle nut and pull out the wheel axle.
  4. Take down the front wheel.
  5. Disassemble the brake drum, dust cover, bearings, and oil seals.

3.2 New Hub Assembly

  1. Clean the bearing holes of the hub and apply high-temperature grease evenly.
  2. Press or gently knock 6202 bearings into place (marked side outward).
  3. Install new oil seals with the lip facing inward.
  4. Reinstall the brake drum and dust cover.
  5. Note: The front brake rocker arm is small-sized and cannot be mixed with rear wheel parts.

3.3 On-board Installation

  1. Align the front fork.
  2. Pass the wheel axle through the left front fork → hub → right front fork in sequence.
  3. Pre-tighten the 17mm nut.
  4. Adjust brake clearance.
  5. Fully tighten the nut to 38-42 N-m after the vehicle is landed.

Rear Wheel Hub Installation

4.1 Old Hub Removal

  1. Jack up the vehicle to lift the rear wheel.
  2. Loosen the brake cable and chain tensioner.
  3. Remove the 17mm axle nut and extract the wheel axle.
  4. Remove the rear wheel.
  5. Disassemble the sprocket base, brake drum, bearings, and oil seals.

4.2 New Hub Assembly

  1. Clean the hub bearing holes and coat with high-temperature grease.
  2. Install 6202 bearings and oil seals.
  3. The rear hub has a flange plate, and the sprocket base is fixed by studs.
  4. Mount the brake drum and sprocket base (confirm correct sprocket direction).
  5. Tighten fixing bolts securely.

4.3 On-board Installation

  1. Run the wheel axle through the right swingarm → hub → left swingarm.
  2. Install and hang the chain on the sprocket.
  3. Adjust chain sag to 20-25mm.
  4. Pre-tighten the axle nut temporarily.
  5. Fine-tune brake clearance.
  6. Tighten the rear axle nut to 45-50 N-m.
  7. Lock the lock nut.

5. Important Notes

  • Bearings must be fully pressed in place.
  • Oil seal lips must face inward to prevent grease leakage and dust ingress.
  • Front and rear brake components & hubs are not interchangeable due to structural differences.
  • Standard torque specifications:
    • Front axle: 38-42 N-m
    • Rear axle: 45-50 N-m
    • Sprocket bolts: 20-25 N-m
  • Recheck chain tightness and brake clearance after installation to avoid deviation or brake dragging.

Maintenance

Regular inspection of your wheel hubs and brake components is crucial for safety and longevity. Check for:

  • Bearing play or roughness.
  • Condition of oil seals for leaks or damage.
  • Brake drum wear and brake shoe condition.
  • Axle nut tightness according to specified torque values.
  • Chain tension and lubrication (for rear wheel).
  • Cleanliness of components to prevent dirt buildup.

Apply high-temperature grease to bearings during assembly and whenever maintenance requires disassembly.

Troubleshooting

Problem Possible Cause Solution
Hub shaking Bearings not installed in place, damaged bearings, or loose axle nuts. Re-seat bearings, replace damaged bearings, tighten axle nuts to specified torque.
Brake dragging Too small brake drum clearance or deformed dust cover friction. Adjust brake clearance, inspect and replace deformed dust cover.
Abnormal noise Lack of grease in bearings, damaged bearings, or improper chain tightness. Apply grease to bearings, replace damaged bearings, adjust chain tightness.

User Tips

  • Always double-check all fasteners for proper torque after initial installation and after the first few rides.
  • Ensure all components are clean before assembly to prevent contamination of bearings and seals.
  • When installing new bearings, apply a thin layer of grease to the outer race to aid installation and prevent corrosion.

Additional Documents

For further detailed diagrams or specific instructions, you may refer to the official user manual PDF:

View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.