RiccoDi DJ70210C-1-21

Contents

RiccoDi 2 Pin Automotive Sensor Plug Connector User Manual

Model: DJ70210C-1-21

1. Introduction

This manual provides essential information for the safe and effective use of your RiccoDi 2 Pin Automotive Sensor Plug Connector. Please read this manual thoroughly before installation and operation, and retain it for future reference.

This connector is designed for automotive applications, specifically compatible with CRV, Rhyme, and Odyssey models for water temperature and inlet pressure sensors. It ensures a fast, stable, waterproof, and dustproof connection.

Product Overview Video: Demonstrates the connector components and general appearance.

2. Safety Warnings

  • Do not use the connector in humid environments to prevent electrical hazards.
  • Never insert or remove the connector while power is applied to the circuit. Always ensure the power supply is off before connecting or disconnecting.
  • Keep out of reach of children.

3. Package Contents

Each kit contains the following components:

  • 1 x Connector Housing and Insert
  • 2 x Terminal
  • 2 x Rubber Seal

Connectors are available in various package quantities (1, 5, 10, or 20 kits) as indicated on your product packaging.

Example of 1 set package contents

Image: Example of a single kit's package contents, showing the connector housing, terminals, and rubber seals.

4. Setup and Installation

Follow these steps for proper installation:

  1. Prepare: Ensure the vehicle's power supply to the relevant circuit is completely off.
  2. Align: Carefully align the connector with the corresponding port on the sensor or wiring harness.
  3. Insert: Gently push the connector into the port until it clicks securely into place. Verify the connection is firm and cannot be easily pulled apart.
  4. Power On: Only after confirming a secure connection, you may restore power to the circuit.
RiccoDi 2 Pin Connector Kit

Image: The RiccoDi 2 Pin Connector kit, showing the main components for assembly.

5. Operating Instructions

Once installed, the connector facilitates the electrical connection for your automotive sensor. No specific operational steps are required beyond ensuring a secure and stable connection.

  • Ensure proper alignment and secure connection before applying power to the circuit.
  • To disconnect, always power off the circuit first, then carefully unlatch and pull the connector.

6. Maintenance

To ensure the longevity and reliable performance of your connector, observe the following maintenance guidelines:

  • Avoid Overloading: Do not exceed the electrical specifications of the connector. Overloading can lead to overheating and damage.
  • Storage: Avoid storing the connector in high-temperature environments, which can degrade the material properties. Store in a cool, dry place.
  • Cleanliness: Periodically check the interface for cleanliness. Dust, dirt, or moisture can lead to poor contact. Clean with a suitable electrical contact cleaner if necessary.
  • Inspection: Regularly inspect the connector and wiring for any signs of wear, damage, or corrosion. Replace if any damage is observed.

7. Troubleshooting

If you encounter issues with your connector, refer to the following common problems and solutions:

  • Poor Contact:
    • Check whether the interface of both the connector and the mating port is clean and free from debris or corrosion.
    • Ensure the terminals are properly crimped and seated within the connector housing.
  • Failure to Connect:
    • Verify that the power supply to the circuit is turned on after installation.
    • Ensure the connector is fully inserted and latched.
    • Confirm compatibility with the sensor or wiring harness.
  • Abnormal Heating:
    • Immediately discontinue use and power off the circuit.
    • Inspect the wiring and connections for any shorts, loose terminals, or signs of damage.
    • Abnormal heating can indicate an overload or faulty connection and should be addressed promptly.

8. Specifications

Attribute Specification
Brand Name RiccoDi (unye)
Model Number DJ70210C-1-21
Application Automotive
Series 1mm Plug Connector
Position 2 Pin
Housing/Connector Material PA66
Terminal/Pins Material Brass/Phosphor Bronze
Rubber Seal Material Silicon Rubber
Origin Mainland China
Certification CE
Wireless Functionality Yes
Includes Battery No
EU LVD Voltage Low voltage: Below 50Vac or 75Vdc
High-concerned chemical None
Voltage None
Gender Female
Terminal Dimensions (H x W x L) 2.05 x 2.15 x 17.5 (mm, approximate)
Material breakdown diagram for connector components

Image: Diagram illustrating the materials used for the connector housing, terminals, and rubber seals.

Close-up of terminals with dimensions

Image: Close-up view of the terminals, showing approximate dimensions.

9. User Tips

  • Compatibility Check: Always verify the connector's compatibility with your specific vehicle model and sensor type (e.g., Honda CRV turn signal connector) before attempting installation.
  • Cleanliness is Key: Ensure all mating surfaces of the connector and the sensor/harness are clean and dry to achieve optimal electrical contact and prevent issues like poor connection.
  • Secure Connection: Double-check that the connector is fully seated and latched to prevent accidental disconnections during vehicle operation.

10. Support Information

For further assistance or detailed technical information, please refer to the official user manual PDF or contact the seller directly.

  • Official User Manual (PDF): A detailed PDF version of the user manual is available for download. Please refer to the product page or contact the seller for the direct link. (Example: View PDF Manual)
  • Seller Contact: For product-specific inquiries, warranty claims, or technical support, please reach out to the RiccoDi AutoAccessories Store directly through the platform where you made your purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.