Introduction
This manual provides detailed instructions for the installation, adjustment, maintenance, and troubleshooting of your Shimano Tourney SL-TX30 Bicycle Shift Lever. The SL-TX30 series includes various models for left (3x7/6-speed friction) and right (6-speed or 7-speed) shifting, all featuring Shimano's OPTICAL GEAR DISPLAY for easy gear position identification.
Important Safety Notice:
- This manual is intended primarily for use by professional bicycle mechanics. Users not professionally trained for bicycle assembly should not attempt installation.
- Always use genuine Shimano parts.
- Do not disassemble or modify the product beyond what is stated in this manual.
- Wear safety glasses or goggles when performing maintenance.
- Keep this manual in a safe place for future reference.
Specifications
| Feature | Detail |
|---|---|
| Brand | SHIMANO |
| Model Number | TX30 |
| Gears | Available in 6-speed, 7-speed, 3x6-speed, 3x7-speed configurations |
| Material | Alloy |
| Type | Conjoined DIP (Dual SIS Index) |
| Components | Derailleurs |
| Features | Optical Gear Display |
Product Variants:
- SL-TX30-LN: Left Shift Lever, 3x7/6-speed (friction)
- SL-TX30-6R: Right Shift Lever, 6-speed
- SL-TX30-7R: Right Shift Lever, 7-speed

Setup and Installation
Tools Required:
- Phillips screwdriver #2
- 5 mm Allen key (or 9 mm spanner for some products)
- Cable cutters (for inner cable and outer casing)
- Grease
1. Mounting the Shifting Lever:
- Install the brake lever first, ensuring it is in a position that will not obstruct the shifting lever operation.
- Position the shifting lever unit on the handlebar so that it does not come into contact with the brake lever when operated from its lowest to highest position.
- Secure the clamp band using a Phillips screwdriver #2.
- Tightening Torque: 2.5 N-m {22 in. lbs.}.
- Note: Do not open the clamp of the lever when installing, as this may damage the cover.

2. Preparing and Connecting the Cable:
- Inserting the Inner Cable: Insert the inner cable into the outer casing from the end with the marking on it. Apply grease to the marked end of the outer casing to maintain cable operating efficiency.
- Cutting the Outer Casing:
- When cutting the outer casing, cut the end opposite to the marked end.
- After cutting, make the end round so that the inside of the hole has a uniform diameter.
- Attach the appropriate outer end cap to the cut end of the outer casing.
- Connecting to Rear Derailleur:
- Connect the cable to the rear derailleur, ensuring it is securely seated in its groove.
- Tightening Torque: 5.0 - 7.0 N-m {44 - 61 in. lbs.}.
- Connecting to Front Derailleur (if applicable):
- Firmly pull the inner cable and connect it to the front derailleur. Pass the cable through as shown in the derailleur's specific diagram (Top Swing or Down Swing).
- Tightening Torque: 5.0 - 7.0 N-m {44 - 61 in. lbs.}.

Operating and Adjustment
Always turn the crank during shifting lever operation to ensure smooth gear changes.
1. Rear Shifting Lever Adjustment:
- Top Adjustment (High Limit):
- Turn the top adjustment screw (usually marked 'H') so that the guide pulley is positioned directly over the outer line of the smallest sprocket when viewed from behind.
- After this adjustment, install the chain.
- Low Adjustment (Low Limit):
- While turning the front chainwheel, operate the lever to shift to the lowest gear (largest sprocket).
- Turn the low adjustment screw (usually marked 'L') so that the guide pulley moves to a position directly below the largest sprocket.
- B-Tension Adjustment (for RD-TX75/RD-TX55/RD-TX35):
- Mount the chain on the smallest chainring and the largest sprocket, then turn the crank arm backward.
- Turn the B-tension adjustment screw to adjust the guide pulley as close to the sprocket as possible without touching it.
- Set the chain to the smallest sprocket and re-check for correct chain tension.
- B-Tension Adjustment (for RD-TZ50):
- Set the chain onto the smallest chainring and the largest sprocket.
- Turn the B-tension adjustment screw to adjust the distance between the tip of the freewheel and the tip of the guide pulley to about 10 mm.
- Set the chain to the smallest sprocket and re-check for correct chain tension.
- SIS (Shimano Index System) Adjustment:
- Operate the shifting lever once to move the chain from the smallest sprocket to the 2nd sprocket.
- While pressing the lever just enough to take up the play, turn the crank arm. The best setting is when the chain touches the 3rd sprocket (counting from the smallest) and makes noise.
- If shifting to the 3rd sprocket causes issues, tighten the outer casing adjustment barrel until the chain returns to the 2nd sprocket.
- If no sound is heard when shifting, loosen the outer casing adjustment barrel until the chain touches the 3rd sprocket and makes noise.
- Return the lever to its original position (2nd sprocket setting) and turn the crank arm clockwise. If the chain still touches the 3rd sprocket and makes noise, turn the outer casing adjustment barrel clockwise slightly until the noise stops and the chain runs smoothly.
- Operate the lever to change gears through all positions and ensure no noise occurs.
2. Front Shifting Lever Adjustment (if applicable):
- Low Adjustment:
- For models with a Pro-Set alignment block, remove it first.
- Adjust so the clearance between the chain guide inner plate and the chain is 0 - 0.5 mm.
- Top Adjustment:
- Adjust so the clearance between the chain guide outer plate and the chain is 0 - 0.5 mm.
- Middle Chainring Adjustment:
- This adjustment is not necessary for LN (friction type) shifters.
- Set the clearance between the chain guide inner plate and the chain to 0 - 0.5 mm.
- Adjust the lever after operating it from the top to the middle position, not from low to middle.
Maintenance
1. General Care:
- Periodically wash the chainrings and chain with a neutral detergent.
- Lubricating the chain after cleaning is an effective way to extend the useful life of the chainrings and chain.
- For maximum performance, we highly recommend using Shimano lubricants and maintenance products.
- Products are not guaranteed against natural wear and deterioration from normal use and aging.
2. Replacing the Inner Cable:
- Press the button on the shifting lever to set the chain to the first position (top for the rear derailleur, low for the front derailleur).
- Carefully pass the inner cable through the lever mechanism.
- Follow the cable connection and adjustment steps outlined in the "Setup and Installation" and "Operating and Adjustment" sections.

Troubleshooting
After completing adjustments, move the shifting lever to check the shifting. If shifting becomes difficult during use, refer to the chart below. Adjust bolts by approximately 1/8 turn for each adjustment.
| Problem | Solution |
|---|---|
| Chain falls to the crank side (front derailleur) | Turn the top adjustment screw clockwise. |
| Difficult shifting from intermediate chainring to largest chainring (front derailleur) | Tighten the cable. If no improvement, turn the top adjustment screw counterclockwise. |
| Difficult shifting from largest chainring to intermediate chainring (front derailleur) | Loosen the cable. |
| Chain falls to the bottom bracket side (front derailleur) | Turn the low adjustment screw clockwise. |
| Intermediate chainring is skipped when shifting from largest chainring (front derailleur) | Tighten the cable. |
| Difficult shifting from intermediate chainring to smallest chainring (front derailleur) | Turn the low adjustment screw counterclockwise. |
| Noisy shifting or chain rubbing (rear derailleur SIS adjustment) | Adjust outer casing adjustment barrel as per SIS adjustment steps in "Operating and Adjustment" section. |
User Tips
- Cable Stretch: After initial installation and a few rides, the inner gear cable may stretch slightly. It is recommended to re-check and fine-tune your shifting adjustments after the first few uses to ensure optimal performance.
- Versatility: The Shimano Tourney SL-TX30 shifters are designed for a wide range of bicycles, including children's bikes, offering reliable performance.
- Smooth Operation: Always ensure the crank is turning when shifting gears to prevent strain on the drivetrain and ensure smooth transitions.
Warranty and Support
For warranty information, please refer to the official Shimano warranty policy provided with your purchase or visit the Shimano website. This product is designed for durability and performance under normal cycling conditions.
For technical support or further assistance, please contact your local authorized Shimano dealer or visit the official Shimano website:
- Shimano Website: http://si.shimano.com
Please note that specifications are subject to change for improvement without notice.