1. Introduction
This manual provides essential information for the safe and effective use, installation, and maintenance of your HTBCCHB Motorcycle Backrest Seat Cushion Pad. Please read this manual thoroughly before installation and keep it for future reference.
2. Product Overview
The Motorcycle Backrest Seat Cushion Pad is designed to provide enhanced comfort for riders. It is constructed from durable foam material and covered with a leather-like finish, suitable for various motorcycle models including Harley, Honda, and Suzuki.
Video: Unboxing and overview of the Motorcycle Backrest Seat Cushion Pad.
3. Safety & Warnings
Adhering to these safety guidelines is crucial for your safety and the longevity of the product.
- Installation Requirements: After installation, ensure the cushion is firmly fixed without any loosening or displacement. This prevents potential safety hazards caused by shifting during riding.
- Compatibility Warning: This product is only applicable to designated vehicle models. It is not interchangeable among different models. Forced installation may result in poor cushion fitting and compromise riding safety.
- Load Limit: Do not exceed the rated load capacity of your vehicle. Exceeding this limit can cause permanent deformation of the cushion under long-term compression.
- Replacement for Damage: Immediately replace the cushion if the leather is torn or the foam is severely collapsed. Further use of a damaged cushion is prohibited.
- Child Safety Warning: Keep the product out of reach of children to prevent risks of accidental ingestion or suffocation.
4. Setup (Installation Instructions)
4.1. Installation Preparation
- Remove the original old seat cushion from your motorcycle.
- Clean the mounting holes on the motorcycle frame. Ensure to clear away any rust and residual fasteners.
- Check that the new seat cushion matches your specific vehicle model. Inspect the cushion for any deformation or damage before installation.
- Prepare all necessary matching screws, nuts, gaskets, and appropriate tools for installation.
4.2. Installation Procedures
- Align the new seat cushion with the mounting position on the motorcycle frame.
- Place the cushion steadily, ensuring all mounting holes are perfectly aligned with the frame.
- Fasten the front and rear fixing points of the seat cushion using the provided screws.
- Tighten the screws evenly to ensure the seat cushion fits tightly without any shaking or looseness.
- Press down on the seat cushion to confirm firm installation. There should be no looseness or abnormal noise.

Image: Underside of the cushion with mounting studs.
5. Operating
Once properly installed, the seat cushion is ready for use. Ensure a comfortable riding posture and always adhere to safe riding practices.
6. Maintenance and Care
6.1. Regular Inspection
- Before every ride, check whether the seat cushion screws are loose. Tighten them if necessary.
- Inspect the cushion leather for any cracks or displacement. Address any issues promptly by adjusting or replacing the cushion.
6.2. Cleaning and Maintenance
- Wipe the leather surface regularly with a damp cloth to remove surface stains.
- For deeper cleaning, use a neutral detergent to keep the leather bright and extend its service life.
- Prohibited Cleaners: Do not use strong acid or alkaline cleaners, or corrosive solvents such as gasoline and banana oil, as these can cause leather corrosion and damage.
6.3. Storage
- Store idle seat cushions in a dry and well-ventilated place.
- Avoid direct sunlight exposure and high-temperature baking, as these can lead to leather aging, fading, and sponge deformation.
6.4. Replacement Cycle
Replace the seat cushion with a new one in a timely manner when the leather has severe scratches, cracks, or the internal sponge collapses.
6.5. Prohibited Operations
- Do not strike the seat cushion with hard objects.
- Do not store the cushion under prolonged direct sunlight.
7. Troubleshooting
Most issues related to the seat cushion can be prevented by proper installation and regular maintenance. If you experience any of the following, please check:
- Cushion Looseness: Re-check all mounting screws and ensure they are tightened evenly and securely.
- Poor Fit: Verify that the cushion is the correct model for your motorcycle. Forcing an incompatible cushion can lead to poor fit and damage.
- Premature Wear/Damage: Ensure the cushion is not exposed to harsh chemicals, extreme temperatures, or excessive loads beyond the vehicle's capacity. Replace if significantly damaged.
8. Specifications
| Feature | Specification |
|---|---|
| Product Name | Motorcycle Backrest Seat Cushion Pad |
| Brand | HTBCCHB |
| Model Name | Motorcycle Seat |
| Material | FOAM |
| Color | Black |
| Item Weight | 0.28 kg |
| Item Length | Approx. 20 cm (8 inches) |
| Item Width | Approx. 15 cm (6 inches) |
| Item Height | Approx. 10 cm (4 inches) |
| Special Features | Motorcycle seats |
| Origin | Mainland China |

Image: Top view showing cushion length (approx. 20cm).

Image: Side view showing cushion width (approx. 15cm).

Image: Front view showing cushion depth/height (approx. 10cm).
9. User Tips
- Always perform a quick check of the cushion's stability and mounting screws before each ride.
- For optimal longevity, clean the cushion regularly with a soft, damp cloth and mild soap.
- When storing your motorcycle for extended periods, consider covering the seat to protect it from dust and direct sunlight.
10. Warranty & Support
10.1. Manufacturer Information
Manufacturer: Yongkang Hongtian Trading Co., Ltd.
Address: Changcheng Village, Yongkang Economic Development Zone, Jinhua City, Zhejiang Province Room 302, 3rd Floor, No. 66 Jinbi Road
Contact: 841996743@qq.com, 86-13018090962
10.2. EU Authorized Representative
Representative: MJCM SARL
Address: 78 avenue des Champs Elysees Bureau 326
Contact: mjcm190928@gmail.com, 33-767213611
10.3. Compliance Information
This product is a motorcycle riding accessory manufactured with eco-friendly materials. It complies with relevant general safety and environmental protection standards of the European Union and meets the sales requirements for the EU market.
10.4. Disclaimer
The manufacturer and seller shall not be held liable for any riding accidents, personal injury, or property loss caused by improper installation, incorrect model matching, man-made damage, or failure of regular maintenance.