HTBCCHB Black Foam Seat Assembly Cushion Pad

Contents

HTBCCHB Black Foam Seat Assembly Cushion Pad User Manual

For Mini Moto Dirt Pocket Bike 47cc 49cc Coolster QG-50

1. Introduction

This manual provides essential information for the safe and effective installation, use, and maintenance of your HTBCCHB Black Foam Seat Assembly Cushion Pad.

1.1 Product Information

  • Product Name: Seat cushion/backrest
  • Model: Black Foam Seat Assembly Cushion Pad

1.2 Manufacturer & EU Representative Information

  • Manufacturer: Yongkang Hongtian Trading Co., Ltd. Changcheng Village, Yongkang Economic Development Zone, Jinhua City, Zhejiang Province Room 302, 3rd Floor, No. 66 Jinbi Road.
  • EU Authorized Representative: MJCM SARL, 78 avenue des Champs Elysees Bureau 326.

1.3 Compliance Information

This product is a motorcycle riding accessory manufactured with eco-friendly materials. It complies with relevant general safety and environmental protection standards of the European Union and meets the sales requirements for the EU market.

2. Safety & Warnings

Please read and understand all safety information before installation and use to prevent injury or damage.

  • Installation Requirements: After installation, ensure the cushion is firmly fixed without loosening or displacement to prevent potential safety hazards caused by shifting during riding.
  • Compatibility Warning: This product is only applicable to designated vehicle models (Mini Moto Dirt Pocket Bike 47cc 49cc Coolster QG-50); it is not interchangeable among different models. Forced installation will result in poor cushion fitting and compromise riding safety.
  • Load Limit: Do not exceed the rated load capacity of the vehicle to avoid permanent deformation of the cushion under long-term compression.
  • Replacement for Damage: Immediately replace the cushion if the leather is torn or the foam is severely collapsed; further use is prohibited.
  • Child Safety Warning: Keep the product out of reach of children to prevent risks of accidental ingestion or suffocation.

3. Installation Instructions

3.1 Installation Preparation

  1. Remove the original old seat cushion from your vehicle.
  2. Clean the mounting holes on the vehicle frame, ensuring to clear away any rust and residual fasteners.
  3. Check that the new seat cushion matches your vehicle model and is free from deformation or damage.
  4. Prepare matching screws, nuts, gaskets, and corresponding tools.

3.2 Installation Procedures

  1. Align the new seat cushion with the mounting position on the frame.
  2. Place it steadily to ensure the holes are perfectly aligned.
  3. Fasten the front and rear fixing points of the seat cushion with screws.
  4. Tighten the screws evenly to ensure the seat cushion fits tightly without shaking.
  5. Press the seat cushion to confirm firm installation. There should be no looseness or abnormal noise.
Underside of the seat cushion showing mounting points and dimensions
Figure 1: Underside view with mounting points (M6) and dimensions (186mm length, 110mm width).
Top view of the seat cushion with length measurement
Figure 2: Top view showing approximate length measurement.
Top view of the seat cushion with width measurement
Figure 3: Top view showing approximate width measurement.

4. Maintenance & Care

4.1 Regular Inspection

  • Before every ride, check if the seat cushion screws are loose.
  • Inspect the leather for any cracks or displacement. Adjust or replace promptly if any problems are found.

4.2 Cleaning and Maintenance

  • Wipe the leather surface regularly with a damp cloth and neutral detergent to keep it bright and extend its service life.
  • Store idle seat cushions in a dry and well-ventilated place.
  • Avoid direct sunlight exposure and high-temperature baking to prevent leather aging, fading, and sponge deformation.

4.3 Replacement Cycle

Replace the seat cushion in a timely manner when the leather has severe scratches, cracks, or the sponge collapses.

4.4 Prohibited Operations

  • Do not strike the seat cushion with hard objects.
  • Do not wipe the leather with corrosive solvents such as gasoline and banana oil.
  • Do not store it under prolonged direct sunlight.

5. Troubleshooting

ProblemPossible CauseSolution
Cushion is loose or shaking after installationImproper installation; screws not tightened sufficiently; incorrect model compatibility.Re-check alignment and tighten all screws evenly. Ensure the cushion is compatible with your vehicle model.
Poor cushion fittingIncorrect model matching; forced installation on incompatible vehicle.Verify product compatibility with your specific Mini Moto Dirt Pocket Bike model. Do not force installation.
Leather torn or foam collapsedWear and tear; excessive load; impact damage; prolonged exposure to harsh conditions.Replace the seat cushion immediately. Further use is prohibited for safety.

6. Specifications

AttributeDetail
Brand NameHTBCCHB
Item TypeFalling Protection
MaterialSponge
ColorBlack
OriginMainland China
Item Weight0.25 kg
Item Height1 inch
Item Width1 inch
Item Length1 inch
Package Weight0.65 kg
Package Dimensions (L x W x H)10 cm x 10 cm x 10 cm
FitmentMini Moto Dirt Pocket Bike 47cc 49cc Coolster QG-50

7. Warranty & Support

7.1 Disclaimer

The manufacturer and seller shall not be held liable for any riding accidents, personal injury, or property loss caused by improper installation, incorrect model matching, man-made damage, or failure of regular maintenance.

7.2 Additional Resources

For a detailed user manual in PDF format, please refer to the official document available at: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.