SHIMANO RD-4700

Contents

SHIMANO Tiagra RD 4700 Rear Derailleur User Manual

Model: RD-4700

Important Notice

This dealer's manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using this manual. If any part of the information is unclear, do not proceed with the installation. Instead, contact your place of purchase or a local bicycle dealer for assistance.

  • Always read all instruction manuals included with the product.
  • Do not disassemble or modify the product other than as stated in this manual.
  • All dealer's manuals and instruction manuals can be viewed online on the Shimano website.
  • Observe all appropriate rules and regulations of your country, state, or region.

DANGER

Failure to follow instructions will result in death or serious injury.

WARNING

Failure to follow instructions could result in death or serious injury.

CAUTION

Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.

To Ensure Safety

  • Use genuine Shimano parts only. Loose or damaged parts can cause serious injury.
  • Always wear safety glasses or goggles when performing maintenance.
  • Keep this manual in a safe place for future reference.
  • **User Information:**
    • Clean the chain regularly with an appropriate chain cleaner. Avoid alkali-based or acid-based solvents, as they can cause chain breakage.
    • Inspect the chain for damage (deformation, cracks), skipping, or other abnormalities. Consult a dealer if problems are found.
    • For installation and maintenance, use an OT-SP sealed outer casing and cable guide.
    • Grease the inner cable and the inside of the outer casing for smooth operation. If grease is wiped off, apply SIS SP41 grease (Y04180000).
    • The outer casing end with an aluminum cap should be on the derailleur side.
    • If gear shifting adjustments fail, check rear fork alignment, cable lubrication, and outer casing length.
    • Periodically clean and lubricate all moving parts of the derailleur (mechanism and pulleys).
    • If tension pulleys have an arrow, install them so the arrow points clockwise when viewed from the outside.
    • Replace pulleys if abnormal noise occurs due to looseness.
    • Product specifications are subject to change for improvement without notice.

List of Tools to Be Used

The following tools are needed for installation, adjustment, and maintenance purposes:

ToolDescription
2mm Hexagon WrenchFor various small adjustments.
3mm Hexagon WrenchFor pulley replacement and plate unit installation.
4mm Hexagon WrenchFor plate axle loosening/tightening.
5mm Hexagon WrenchFor B-tension adjust bolt and general installation.
Screwdriver [#2]For top and low adjustment screws, and plate stopper pin.
Slotted ScrewdriverFor removing B axle stop ring (RD-6800/RD-5800/RD-4700).
Snap Ring PliersFor removing/installing B axle stop ring (RD-9000).

Setup (Installation)

1. Installing the Derailleur

When installing, ensure the B-tension adjust bolt does not contact the fork end tab, which could cause deformation.

Diagram showing the rear derailleur installation with a 5mm hexagon wrench and the B-tension adjust bolt position.

Diagram showing the rear derailleur installation with a 5mm hexagon wrench and the B-tension adjust bolt position. The B-tension adjust bolt (C) should not contact the fork end tab (B).

Use a 5mm hexagon wrench to tighten the B-tension adjust bolt to 8-10 N-m.

NOTE

  • Insert the hexagon wrench fully into the bracket axle tool hole.
  • Do not use a ball point hexagon wrench, as incorrect tightening can deform the tool hole or lead to suboptimal gear shifting.

2. Chain Length

Proper chain length is crucial for optimal shifting performance.

  • Assemble with sprocket max 27T or less: Place the chain on the smallest sprocket and largest chainring. The guide pulley (E) and tension pulley (F) should form a right angle (90°) to the ground.
  • Diagram illustrating correct chain length for a maximum 27T sprocket, showing the guide and tension pulleys forming a 90-degree angle.

    Diagram illustrating correct chain length for a maximum 27T sprocket, showing the guide and tension pulleys forming a 90-degree angle.

  • Assemble with sprocket max 28T or more: With the chain on both the largest sprocket and the largest chainring, add 2 links to the minimum number of links that can be connected.
  • Diagram illustrating chain length for a maximum 28T sprocket or more, showing the addition of two links.

    Diagram illustrating chain length for a maximum 28T sprocket or more, showing the addition of two links.

  • For front triple, assemble with sprocket max 30T or less: When installing the chain, place it in the largest chainring and smallest sprocket.
  • For front triple, assemble with sprocket max 32T or more: With the chain on both the largest sprocket and the largest chainring, add 2 links to the minimum number of links that can be connected.

3. Chain Routing

The rear derailleur plate assembly has a pin or plate to prevent chain derailment. When passing the chain, route it through the rear derailleur body from the side of this pin/plate.

Diagram showing correct chain routing through the rear derailleur, passing from the side of the pin/plate to prevent derailment.

Diagram showing correct chain routing through the rear derailleur, passing from the side of the pin/plate to prevent derailment. Incorrect routing can damage the chain or derailleur.

Operating (Adjustment)

1. SIS Adjustment

Top Adjustment

Turn the top adjustment screw (D) so that the guide pulley (B) is directly below the outer line of the smallest sprocket (A) when viewed from the rear.

Diagram illustrating top adjustment of the derailleur, showing the guide pulley alignment with the smallest sprocket.

Diagram illustrating top adjustment of the derailleur, showing the guide pulley alignment with the smallest sprocket. Use a #2 screwdriver for adjustment.

Securing of Inner Cable

Connect the cable to the rear derailleur. After taking up the initial slack, re-secure the cable as shown in the illustration.

Diagram showing how to secure the inner cable to the rear derailleur, ensuring it is properly seated in the groove.

Diagram showing how to secure the inner cable to the rear derailleur, ensuring it is properly seated in the groove. Ensure the cable is securely in the groove. Fuzz may be generated but will not affect function. Replace the cover with tongue along with the inner cable. Note: A cover with tongue is only attached to RD-9000, 6800, and 5800 models.

Inner Cable Routing

In some cases, an arrow indicates the inner cable's path. Use this as a reference.

Diagram showing inner cable routing for RD-9000/RD-6800-SS/RD-5800-SS/RD-5800-GS/RD-4700-SS models.

Diagram showing inner cable routing for RD-9000/RD-6800-SS/RD-5800-SS/RD-5800-GS/RD-4700-SS models. Tighten the 4mm hexagon wrench to 6-7 N-m.

Diagram showing inner cable routing for RD-6800-GS/RD-4700-GS models, highlighting a different groove position.

Diagram showing inner cable routing for RD-6800-GS/RD-4700-GS models, highlighting a different groove position. Tighten the 4mm hexagon wrench to 6-7 N-m.

Low Adjustment

Turn the low adjustment bolt (D) so that the guide pulley (B) moves to a position directly beneath the largest sprocket (A).

Diagram illustrating low adjustment of the derailleur, showing the guide pulley alignment with the largest sprocket.

Diagram illustrating low adjustment of the derailleur, showing the guide pulley alignment with the largest sprocket. Use a #2 screwdriver for adjustment. If wheel spokes are too close to the inner plate, adjust the low adjustment screw.

Adjusting the B-Tension Adjust Bolt

Mount the chain on the smallest chainring and the largest sprocket, then turn the crank arm backward. Turn the B-tension adjust bolt (D) to position the guide pulley as close as possible to the sprocket without touching it. Repeat for the smallest sprocket to ensure no contact.

SIS Adjustment Steps

  1. Operate the shifting lever several times to move the chain to the 2nd sprocket. While operating the lever just enough to close the gap, turn the crank arm.
  2. Adjust gear positions by turning the cable adjustment barrel. The best setting is when the shifting lever is operated just enough to close the lever gap, and the chain touches the 3rd sprocket, making noise.
  3. Return the lever to its original position (2nd sprocket setting, released) and turn the crank arm clockwise. If the chain touches the 3rd sprocket and makes noise, tighten the cable adjustment barrel clockwise slightly until the noise stops.
  4. Operate the lever to change gears and check for noise in all gear positions.

TECH TIPS

For best SIS performance, periodically lubricate all power-transmission parts.

Advice on Usage of Junior Teeth Group (CS-6800 14-28T)

If shift shock occurs during inward gear shifting, perform the following adjustment:

  1. Tighten the B-tension adjust bolt in direction [A].
  2. Turn the cable adjustment barrel clockwise (until shift shock is alleviated), then move the guide pulley outwards.

Maintenance

1. Replacement of the Pulley

  1. Replace pulleys using a 3mm hexagon wrench. Tighten to 2.5-5 N-m.

NOTE

  • For RD-9000, apply sufficient grease to the inside of the pulley cap.
  • The RD-4700 pulley does not have an arrow.

2. Installing the B Axle and B Axle Cap

Removing the B Axle Cap (RD-9000)

  1. Hold down the B axle cap and the B axle cap C ring.
  2. Widen the slit in the B axle cap C ring using a pointed tool, then remove the B axle cap C ring, B axle cap, and B axle bent washer.

CAUTION

Be careful not to injure your fingers with the pointed tool.

Removing the B Axle (RD-9000)

  1. Widen the B axle stop ring using snap ring pliers and remove it from the B axle. Press the B axle in the direction of the arrow while removing the stop ring.
  2. Remove the B axle washer and the B axle from the bracket body in the direction of the arrow.

Removing the B Axle (RD-6800/RD-5800/RD-4700)

  1. Remove the B axle stop ring using a slotted screwdriver.

CAUTION

Be careful when removing the B axle stop ring as the stopper plate may pop out under spring force.

  1. Use pliers to remove the stopper plate by moving it in the direction of the arrow.
  2. Remove the B axle seal ring and the B tension spring, then remove the B axle in the direction of the arrow.

Mounting the B Axle

NOTE

Apply sufficient grease to the sliding portions (B axle, B axle bearing, B axle washer, stopper plate) and the B tension spring.

  1. When mounting the B tension spring, insert the longer end into the bracket body side and the shorter end into the hole on the stopper plate side.
  2. Temporarily assemble the B tension spring, B body seal ring, stopper plate (with B tension adjustment bolt) and B axle to the B body.
  3. Hook a 3mm hexagon wrench as illustrated, and turn it counterclockwise.
  4. Turn the hexagon wrench until the claw on the stopper plate crosses the claw on the B body.
  5. Insert the hexagon wrench. If difficult, push it in by moving it slightly.
  6. Hook the stopper plate onto the stopper claw on the bracket body.

Mounting the B Axle Cap

  1. Mount the B axle bent washer to the bracket body. Pay attention to the direction.
  2. Mount the B axle cap and the B axle cap C ring. Ensure the C ring is securely mounted to the groove on the B axle.

3. Removing the Plate Unit (RD-9000/RD-6800)

  1. Remove the plate stopper pin using a #2 screwdriver.
  2. Turn the plate to loosen the plate tension spring as shown in the illustration.
  3. Remove the pulley with a 3mm hexagon wrench.
  4. Loosen the plate axle with a 4mm hexagon wrench.

4. Installing the Plate Unit (RD-9000/RD-6800)

  1. Apply grease to the plate axle.
  2. Insert the tip of the plate tension spring into the plate unit spring hole.
  3. Insert the end of the plate tension spring into the groove of the plate.
  4. Tighten the plate axle with a 4mm hexagon wrench to 8.8-10.8 N-m.

5. Removing the Plate Unit (RD-5800/RD-4700)

  1. Loosen the stopper bolt with a 2mm hexagon wrench.
  2. Remove the stopper bolt. Press the plate firmly with your hand while removing the stopper bolt due to tension from the plate tension spring.
  3. Lift the plate (y), then turn slowly until the plate stopper pin surpasses the plate unit stopper (z).
  4. Slowly remove the plate.

6. Installing the Plate Unit (RD-5800/RD-4700)

  1. Ensure the plate unit seal ring is fully inserted all the way to the rear.
  2. Insert the tip of the plate tension spring into the plate unit spring hole. Insert the side of the plate tension spring with the larger outer diameter into the spring hole on the side of the plate unit.
  3. Apply grease to the plate axle.
  4. Insert the tip of the plate tension spring into the plate hole.
  5. Turn the plate in the direction indicated by the arrow, tighten the plate tension spring so it is not loose, and then insert the plate. Turn the plate until the plate stopper pin draws near the plate unit stopper. Relax the force holding the plate, then lift it (y), and turn until the plate stopper pin surpasses the plate unit stopper (z).
  6. Press firmly so the plate cannot be removed. Insert the stopper bolt, then tighten with a 2mm hexagon wrench to 0.88-1.27 N-m. Use a new stopper bolt.

7. Replacing the Cable

  1. Remove the cable.
  2. Remove the cable adjustment barrel and then the cover with tongue.
  3. Attach a new cover with tongue.
  4. Screw the cable adjustment barrel down to the appropriate point.
  5. Attach a new cable.

Troubleshooting

  • Gear Shifting Issues: If gear shifting adjustments cannot be carried out smoothly, check the rear fork ends for alignment. Also, ensure the cable is lubricated and clean, and verify that the outer casing is neither too long nor too short.
  • Abnormal Pulley Noise: If you hear abnormal noise due to looseness in a pulley, replace the pulley.
  • Excessive Link Looseness: If the looseness in the derailleur links is so great that gear shifting adjustments cannot be made, the derailleur should be replaced.
  • Chain Derailment: Ensure the chain is passed through the rear derailleur plate assembly correctly, from the side of the pin/plate. Incorrect routing can cause damage.
  • Wheel Spoke Interference: If the wheel spokes are too close to the inner plate of the rear derailleur, adjust the low adjustment screw to create clearance.
  • Inward Gear Shifting Shock (Junior Teeth Group): If experiencing shift shock when shifting inward with a junior teeth group (e.g., CS-6800 14-28T), tighten the B-tension adjust bolt and then adjust the cable adjustment barrel clockwise until the shock is alleviated, moving the guide pulley outwards.

Specifications

AttributeValue
Brand NameSHIMANO
Model NumberRD-4700
TypeRear Derailleur
ComponentsDerailleurs
Gears10 Speed
MaterialAluminum
OriginJapan (Jp)
High-concerned chemicalNone
RD-4700-SS Specifics
Cassette Compatibility10-speed
Maximum SprocketLow sprocket: 28T / Top sprocket: 14T
Minimum SprocketLow sprocket: 25T / Top sprocket: 11T
Total Capacity33T
RD-4700-GS Specifics
Cassette Compatibility10-speed
Maximum SprocketLow sprocket: 34T / Top sprocket: 12T (front double) / Low sprocket: 32T / Top sprocket: 12T (front triple)
Minimum SprocketLow sprocket: 28T / Top sprocket: 11T (front double) / Low sprocket: 25T / Top sprocket: 11T (front triple)
Total Capacity39T (front double) / 41T (front triple)

Product Overview

Video showcasing the SHIMANO Tiagra RD 4700 Rear Derailleur, highlighting its design and movement.

SHIMANO Tiagra RD 4700 Rear Derailleur, showing both SS and GS models.

SHIMANO Tiagra RD 4700 Rear Derailleur, showing both SS and GS models.

Close-up of the RD-4700 SS model.

Close-up of the RD-4700 SS model.

Close-up of the RD-4700 GS model.

Close-up of the RD-4700 GS model.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur from a different angle.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur from a different angle.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur, showing the pulley cage.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur, showing the pulley cage.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur, highlighting the Tiagra branding.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur, highlighting the Tiagra branding.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur, showing the rear view.

Product image of the SHIMANO Tiagra RD 4700 Rear Derailleur, showing the rear view.

User Tips

  • This derailleur is designed for road bikes.
  • The product is confirmed to be original Shimano.
  • Users report easy setup and perfect functionality.
  • Consider the GS version for compatibility with larger cassettes (up to 34T).
  • For detailed step-by-step instructions on fine-tuning adjustments, consult additional resources or professional guidance.

Warranty & Support

For further assistance, technical documentation, or warranty information, please contact the appropriate Shimano regional office:

  • SHIMANO AMERICAN CORPORATION
    One Holland, Irvine, California 92618, U.S.A.
    Phone: +1-949-951-5003
  • SHIMANO EUROPE B.V.
    High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
    Phone: +31-402-612222
  • SHIMANO INC.
    3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

Please note that specifications are subject to change for improvement without notice.

For the most up-to-date dealer's manuals and instruction manuals, visit the official Shimano website: http://si.shimano.com.

A user manual in PDF format is also available: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.