QIACHIP KR1204B

Contents

QIACHIP 433.92Mhz 4CH Relay Module Receiver User Manual

Model: KR1204B

1. Introduction

This manual provides detailed instructions for the QIACHIP 433.92Mhz 4-channel wireless remote control switch receiver, Model KR1204B. This versatile module is designed for various DIY applications, including controlling DC motors, lights, automated curtains, garage doors, and more. It supports multiple working modes and offers easy pairing with QIACHIP remote controls.

QIACHIP 4CH Relay Module Receiver with multiple remote controls
Figure 1: QIACHIP 4CH Relay Module Receiver and Remote Controls

2. Safety Information

  • Do not install with electricity. Always ensure the power supply is turned off before wiring the module. Verify all connections are correct before applying power.
  • When using wireless electronic products, avoid strong interference sources such as metal shields, large electronic equipment, and electromagnetic fields, as these can shorten the remote control distance or cause abnormal operation.
  • Do not use this electronic product abnormally. Abnormal use may reduce product performance and lifespan, and in severe cases, may cause damage to the product and pose safety hazards.

3. Product Overview

The QIACHIP KR1204B receiver features a learning button for pairing, an indicator LED, and terminals for power input and output. The module operates within a DC 5V-80V range.

Detailed view of the QIACHIP receiver board with labeled components
Figure 2: Receiver Component Identification

Key Components:

  • Antenna: For receiving RF signals from the remote control.
  • Indicator: LED light to show status (e.g., learning mode, signal reception).
  • Learning Button: Used for pairing remote controls and resetting the module.
  • Relay: Four independent relays for controlling connected devices.
  • Input / Output Volts (1V~250V): Terminals for connecting devices to be controlled (NO, COM, NC).
  • Power Supply (DC 5V-80V): Terminals for providing power to the receiver module (+V, GND).

4. Specifications

Attribute Value
Input PowerDC 5V-80V
RF Frequency433.92MHZ
Standby Current5mA
Load Power120W × 4
Matching ModeLearning Button
Receiving Sensitivity>97dbm
Operation ModeMomentary, Toggle, Latching Mode
OutputNO, NC, COM
Support Encoding ChipLearning Code (1527)
Modulation ModeASK
Maximum Paired RemotesNo more than 20 pcs
Working Temperature-20 ~ 80°C
Dimensions73x55x30 (mm)
Channel4
Wireless CommunicationRF
Support APPNo
CertificationCE

5. Setup and Wiring

Important Note: All working modes described below require QIACHIP brand remote controls (transmitters) and the KR1204B receiver. Compatibility with remote controls from other brands is not guaranteed.

5.1. Wiring Diagrams

Below are common wiring configurations for DC lamps and DC motors. Ensure power is disconnected before making any connections.

Wiring diagrams for DC lamps and two DC motors
Figure 3: Wiring Diagrams for DC Lamps and DC Motors

DC Lamp Wiring Diagram:

Connect the DC power supply to the +V and GND terminals. Connect the lamps to the NO (Normally Open) and COM (Common) terminals for each channel. When the relay is activated, the circuit between NO and COM will close, powering the lamp.

DC Motor Wiring Diagram (Two Motors):

Connect the DC power supply to the +V and GND terminals. For each motor, connect its two wires to the NO and COM terminals of two separate relays. This configuration allows for forward and reverse control of the motor by activating different relays. For example, to control two DC motors, you would use two channels for each motor (total of 4 channels for two motors).

5.2. Reset Function

To clear all previously paired remote controls from the receiver's memory:

  1. Press the receiver's learning button 8 times.
  2. The receiver's LED will flash and then turn off, indicating that all remote control data has been cleared. After a reset, no remote control will be able to operate the receiver until re-paired.

6. Operating Modes

The wireless remote control switch supports three working modes: Momentary, Toggle, and Latching. The working mode can only be set when the LED indicator on the switch controller is lit.

6.1. Momentary Mode (Jog)

In this mode, the relay is active only while the remote control button is pressed. Releasing the button turns the relay off.

Setting Momentary Mode:

  1. Press the receiver's learning button once.
  2. Wait for the LED on the receiver to light up, indicating it has entered the setting state.
  3. Press a button on the remote control (e.g., button A) once. The LED on the receiver will flash and then turn off. The Momentary mode is now successfully set.

6.2. Toggle Mode (Self-Locking)

In this mode, pressing the remote control button once turns the relay on, and pressing the same button again turns the relay off.

Setting Toggle Mode:

  1. Press the receiver's learning button twice.
  2. Wait for the LED on the receiver to light up, indicating it has entered the setting state.
  3. Press a button on the remote control (e.g., button A) once. The LED on the receiver will flash and then turn off. The Toggle mode is now successfully set.

6.3. Latching Mode (Interlock)

In this mode, pressing one remote control button turns on its corresponding relay and turns off any other active relays. This is useful for applications where only one output should be active at a time.

Setting Latching Mode:

  1. Press the receiver's learning button three times.
  2. Wait for the LED on the receiver to light up, indicating it has entered the setting state.
  3. Press a button on the remote control (e.g., button A) once. The LED on the receiver will flash and then turn off. The Latching mode is now successfully set.
Diagram showing how to set Momentary, Toggle, and Latched modes
Figure 4: Mode Setting Instructions

7. Operation

Once the desired operating mode is set and the remote control is paired, you can control your connected devices:

  • Momentary Mode: Press and hold the paired remote button to activate the relay. Release to deactivate.
  • Toggle Mode: Press the paired remote button once to activate the relay. Press it again to deactivate.
  • Latching Mode: Press a remote button (e.g., A) to activate its corresponding relay. Press another button (e.g., B) to deactivate relay A and activate relay B.

Watch the product demonstration video for a visual guide on operation:

Video 1: Product Demonstration of Relay Module and Remote Control

8. Maintenance

  • Remote Control Battery: If the remote control's range decreases or it becomes unresponsive, the battery may be low. Replace the CR2016 3V battery in the remote control as needed.
  • Cleaning: Keep the receiver module and remote controls clean and free from dust and moisture. Use a dry, soft cloth for cleaning.

9. Troubleshooting

  • Remote not working after pairing: Ensure the receiver's LED flashes and turns off after pairing, indicating successful programming. If not, repeat the pairing process.
  • Short remote control distance: Check the remote control battery. Ensure there are no strong interference sources (metal objects, large electronic devices) between the remote and the receiver.
  • Relays not activating: Verify all wiring connections are secure and correct according to the diagrams. Ensure the power supply to the receiver is within the specified DC 5V-80V range.
  • Multiple relays blowing: This indicates a potential wiring error or overload. Double-check your load power (should not exceed 120W per channel) and ensure correct voltage and current for your connected devices. Always wire with power off.

10. User Tips

  • Many users find this module excellent for garage door openers and e-bike gear switches due to its reliable wireless control.
  • The module is generally easy to program and install, making it suitable for various DIY projects.
  • For optimal performance, ensure the wiring is neat and secure, and avoid placing the receiver near large metal objects that could block the RF signal.

11. Frequently Asked Questions (FAQ)

Q: What are the benefits of using this product?
A: The benefits include convenient control over various devices, improved security with access control systems, and flexibility in choosing different working modes.
Q: What are some common applications for this module?
A: Common applications include electric doors, automated curtains, lighting, general switches, garage doors, car sunroofs, and other access control systems.
Q: How many remote controls can be paired with one module?
A: The module supports pairing with no more than 20 remote controls.
Q: Can I use this with a 67.2V battery?
A: Yes, the module supports a wide input voltage range from DC 5V to 80V, so 67.2V is within the acceptable range.
Q: Is it possible to control two motors simultaneously, both forward and backward?
A: Yes, with its 4 channels, you can configure two channels per motor to control forward and reverse movement, allowing for simultaneous control of two motors.

12. Warranty and Support

For detailed warranty information and further technical support, please visit the official QIACHIP website at www.qiachip.com. You may also find additional resources and services there.

A user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.