Hongwin 0227100140

Contents

Ignition Control Module User Manual

Model: 0227100140

1. Product Overview

This document provides instructions for the Hongwin Ignition Control Module, designed for various Citroen, Ford, and Peugeot models (1.0L-2.0L, 1986-1999). This module is a critical component of your vehicle's ignition system, responsible for controlling the timing and duration of the ignition spark.

Important: Please read all instructions carefully before installation and use. Professional installation is recommended.

2. Safety Information

2.1 General Safety

  • Always disconnect the vehicle's battery before working on any electrical components to prevent electrical shock or damage to the vehicle's systems.
  • Wear appropriate personal protective equipment (PPE), such as safety glasses and gloves.
  • Ensure the engine is cool before beginning any work.
  • Keep all tools and parts away from moving engine components.

2.2 Packaging Warning

TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES, OR PLAY PENS. THIS BAG IS NOT A TOY.

3. Setup and Installation

Before installation, ensure the module matches your vehicle's specifications and connector type. Refer to the dimensions and model type carefully.

3.1 Pre-Installation Checks

  1. Verify the part number (0227100140) matches your vehicle's requirements.
  2. Inspect the module for any visible damage.
  3. Confirm the connector types (2-pin and 3-pin) match your vehicle's harness.

3.2 Wiring Diagram and Connectors

The module features both 2-pin and 3-pin connectors. Pay close attention to the pin assignments for correct operation.

Ignition Control Module with 2-pin and 3-pin connectors and wiring diagram
Figure 1: Ignition Control Module showing 2-pin and 3-pin connectors, and a detailed wiring diagram. The diagram indicates terminals B-, P-, P+, B+, and B-C.

Wiring Terminal Identification:

  • B-: Battery Negative / Ground
  • P-: Primary Coil Negative
  • P+: Primary Coil Positive
  • B+: Battery Positive (Switched)
  • B-C: Battery Negative / Ground (often for control signal)

Take care when connecting the plug to ensure proper alignment and secure connection.

3.3 Installation Steps

  1. Disconnect the negative terminal of the vehicle's battery.
  2. Locate the existing ignition control module.
  3. Carefully disconnect the electrical connectors and remove any mounting screws.
  4. Remove the old module.
  5. Apply a thin layer of thermal paste (if not pre-applied) to the mounting surface of the new module to ensure proper heat dissipation.
  6. Mount the new Hongwin Ignition Control Module securely using the original hardware.
  7. Connect the electrical connectors, ensuring they click into place. Double-check all connections.
  8. Reconnect the negative terminal of the vehicle's battery.
  9. Start the vehicle and check for proper operation.

4. Operating Principles

The Ignition Control Module (ICM) receives signals from the engine's crankshaft position sensor or distributor. Based on these signals, the ICM precisely controls the primary circuit of the ignition coil, determining when to charge and discharge the coil to create a high-voltage spark at the spark plugs. This ensures optimal engine performance and fuel efficiency.

Proper operation is indicated by the vehicle starting reliably, running smoothly, and exhibiting no misfires or hesitation during acceleration.

5. Maintenance

The Hongwin Ignition Control Module is a sealed unit and requires no routine user maintenance. However, periodic inspection is recommended:

  • Visually inspect the module and its connections for any signs of damage, corrosion, or loose wiring during routine vehicle maintenance.
  • Ensure the electrical connectors are clean and free from dirt or moisture.
  • Check for any signs of overheating, such as discoloration or melting of the plastic housing.

If any issues are observed, consult a qualified automotive technician.

6. Troubleshooting

If your vehicle experiences ignition-related problems after installing or while using the module, consider the following:

6.1 Common Symptoms of a Faulty Ignition Control Module

  • Engine cranks but does not start (no spark).
  • Engine misfires or runs rough.
  • Engine stalls unexpectedly.
  • Poor fuel economy.
  • Check Engine Light (CEL) illuminated with ignition-related fault codes.

6.2 Troubleshooting Steps

  1. Check Connections: Ensure all electrical connectors to the module are securely attached and free of corrosion.
  2. Inspect Wiring: Look for any frayed, cut, or damaged wires leading to or from the module.
  3. Test Other Components: A faulty ignition coil, spark plugs, or crankshaft position sensor can mimic ICM symptoms. Test these components if possible.
  4. Professional Diagnosis: If symptoms persist, it is highly recommended to have the vehicle diagnosed by a qualified automotive technician using specialized diagnostic tools.

7. Specifications

FeatureSpecification
Model Number0227100140
Manufacturer Part Number64833060
Interchange Part Number0227100140
OEM NO.0 227 100 140 / 1 227 022 017 / 1 227 022 018 / 1 227 022 031 / 1 237 010 0
MaterialPLASTIC
Ignition TypeSeparate Ignition
TypeClosed Magnetic
Country of OriginChina Mainland
Length69.2 mm (2.72 inches)
Width57.7 mm (2.27 inches)
Dimensions of the Ignition Control Module
Figure 2: Dimensions of the Ignition Control Module.

8. Warranty and Support

For further assistance or warranty inquiries, please contact Hongwin customer support:

  • Brand: Hongwin
  • Manufacturer: Wenzhou Haowei Auto Parts Co., Ltd.
  • Manufacturer Address: Floor 2, Building 8 (West), Hantian Hardware and Electrical City, Tangxia Town, Ruian City, Zhejiang Province, China
  • Customer Service Email: inf@hwautoparts.com
  • Telephone: +86-18005775583

EU Representative:

  • Representative: MJCM SARL
  • Address: CN-78 avenue des Champs Elysees Bureau 326
  • Telephone: +33-767213611
  • E-mail: mjcm190928@gmail.com

An additional user manual in PDF format may be available for download: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.