diymore MB102 Micro USB Breadboard Power Supply

Contents

MB102 Micro USB Breadboard Power Supply Module

User Instruction Manual

1. Introduction

The diymore MB102 Micro USB Breadboard Power Supply Module is designed to provide stable 3.3V and 5V power rails directly to your MB102 solderless breadboard. It is an essential tool for DIY electronics projects, especially when working with microcontrollers like Arduino, offering convenience and flexibility for prototyping.

2. Safety Information

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always ensure correct polarity when connecting power sources. Do not exceed the maximum input voltage or output current ratings to prevent damage to the module or connected components.

3. Package Contents

Please check the package for the following items:

  • 1 x MB102 Micro USB Breadboard Power Supply Module
  • 1 x 830 Point Solderless Breadboard (may be included depending on kit variation)
MB102 Power Supply Module and 830 Point Breadboard
Figure 3.1: MB102 Power Supply Module and 830 Point Solderless Breadboard. This image shows the power supply module alongside a standard 830-point breadboard, illustrating how they are typically used together.

4. Specifications

FeatureDescription
Model NumberMB102 Micro USB Breadboard Power Supply
Input VoltageDC 6.5-12V (via DC barrel jack) or USB power supply
Output Voltage3.3V / 5V (switchable)
Maximum Output Current<700 mA
Output ControlTwo independent output groups, switchable to 0V, 3.3V, or 5V
Output PinsOn-board two groups of 3.3V, 5V DC output plug pins
ApplicationComputer, DIY Electronics, Prototyping
TypeVoltage Regulator
Dimensions5.3cm x 3.5cm
ConditionNew
OriginMainland China
MB102 Power Supply Module with dimensions
Figure 4.1: MB102 Power Supply Module with a ruler for precise dimensions. The module measures approximately 5.3cm by 3.5cm.

5. Setup Instructions

  1. Attach to Breadboard: Align the power pins of the MB102 module with the power rails (usually marked with '+' and '-') on your MB102 solderless breadboard. Gently press the module into place, ensuring a secure connection.
  2. Select Output Voltage: The module has two sets of 3-pin jumpers, one for each side of the breadboard. Use the small yellow jumpers to select the desired output voltage (3.3V or 5V) for each power rail. Move the jumper to connect the middle pin to either the '3.3V' or '5V' pin.
  3. Connect Power Input:
    • DC Barrel Jack: Connect a DC power adapter (6.5V to 12V) to the barrel jack input.
    • USB Power: Alternatively, connect a standard USB cable to the USB-A port on the module.
  4. Power On: Flip the white ON/OFF switch to the 'ON' position. The green LED indicator on the module should illuminate, indicating that power is being supplied.
Close-up of MB102 Power Supply Module
Figure 5.1: Close-up view of the MB102 Power Supply Module. This image highlights the DC barrel jack, USB port, ON/OFF switch, voltage selection jumpers, and output pins.

6. Operating Instructions

  1. Verify Voltage Selection: Before connecting any components to your breadboard, double-check that the voltage selection jumpers are set to the correct voltage (3.3V or 5V) required by your circuit.
  2. Powering Your Circuit: Once the module is powered on and the LED is lit, the selected voltage will be available on the corresponding power rails of your breadboard. You can then connect your components and circuits to these rails.
  3. Independent Control: The module features two independent output groups, allowing you to supply different voltages (e.g., 3.3V on one side and 5V on the other) or to switch off power to one side while the other remains active.
  4. Power Off: To safely power down your circuit, flip the white ON/OFF switch to the 'OFF' position. The green LED will turn off.
Top view of MB102 Power Supply Module showing switch and jumpers
Figure 6.1: Top view of the MB102 Power Supply Module. This image clearly shows the white ON/OFF switch and the yellow voltage selection jumpers for each power rail.

7. Maintenance

  • Keep the module clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Avoid exposing the module to moisture or extreme temperatures.
  • Store the module in a dry, static-free environment when not in use.
  • Regularly inspect connections for any signs of wear or damage.

8. Troubleshooting

  • No Power LED:
    • Ensure the ON/OFF switch is in the 'ON' position.
    • Check that the input power source (DC adapter or USB) is properly connected and providing power.
    • Verify the input voltage is within the specified range (DC 6.5-12V).
  • Incorrect Output Voltage:
    • Ensure the voltage selection jumpers are correctly placed for the desired 3.3V or 5V output.
    • Check for any short circuits on the breadboard that might be drawing excessive current and causing voltage drop.
  • Module Gets Hot:
    • This may indicate an overcurrent condition. Disconnect your circuit and check for short circuits or components drawing more than 700mA.
    • Ensure the input voltage is not excessively high, as higher input voltage can lead to more heat dissipation by the voltage regulator.

9. User Tips

  • This module is ideal for DIY electronics projects and solderless prototyping, making it easy to power your breadboard circuits.
  • Always test your circuit with a multimeter before connecting sensitive components to ensure the correct voltage is being supplied.

10. Warranty and Support

For any issues or support inquiries, please contact your retailer or the manufacturer. Keep your proof of purchase for warranty claims.

A detailed user manual in PDF format may be available for download at: MB102 Power Supply Module PDF Manual

© 2024 diymore. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.