diymore HX-2S-D01

Contents

diymore HX-2S-D01 2S 6.4V 8A Battery Protection Board User Manual

Model: HX-2S-D01

1. Product Overview

The diymore HX-2S-D01 is a 2S 6.4V 8A Lithium Iron Phosphate (LiFePO4) and Li-ion Battery Protection Board (BMS) designed to safeguard your battery pack. It integrates essential protection functions to ensure the longevity and safety of your batteries.

Key Features:

  • Overcharge Protection
  • Overdischarge Protection
  • Short Circuit Protection
  • Overcurrent Protection

While the product name includes 'Balance Charger Protect Module', the primary functions described are focused on protection. Users should verify if active cell balancing is a required feature for their application, as some user feedback indicates it may not actively balance cells.

2. Setup and Wiring Instructions

Careful wiring is crucial for the correct operation and safety of the battery protection board. Refer to the diagram below for proper connections.

Wiring diagram for HX-2S-D01 BMS board
Figure 1: HX-2S-D01 Wiring Diagram

Connection Steps:

  1. B+ Connection: Connect the B+ terminal on the board to the positive electrode of the battery pack.
  2. B- Connection: Connect the B- terminal on the board to the negative electrode of the battery pack.
  3. BM Connection: Connect the BM terminal on the board to the connection point between battery 1 and battery 2. This is the midpoint for a 2S configuration.
  4. P+ Connection: Connect the P+ terminal on the board to the positive electrode of your charge/discharge terminal. This terminal is shared for both charging and discharging.
  5. P- Connection: Connect the P- terminal on the board to the negative electrode of your charge/discharge terminal. This terminal is also shared for both charging and discharging.

Warning: Ensure all connections are correct before applying power. Incorrect wiring can damage the board, batteries, or connected devices.

3. Operation

Once correctly wired, the HX-2S-D01 board continuously monitors the battery pack's voltage and current to provide protection. It operates automatically, engaging protection mechanisms when thresholds are exceeded.

Protection Functions:

  • Overcharge Protection: Prevents batteries from being charged beyond their safe voltage limit.
  • Overdischarge Protection: Disconnects the load when battery voltage drops below a safe minimum, preventing deep discharge.
  • Overcurrent Protection: Limits the current drawn from or supplied to the battery to prevent damage from excessive current.
  • Short Circuit Protection: Immediately cuts off power in the event of a short circuit. This protection features a delayed self-recovery mechanism.

4. Specifications

ParameterValue
Model NumberHX-2S-D01
Dimensions41mm x 16mm x 3.5mm
Supply Voltage6.4V (for 2S LiFePO4)
Maximum Operating Current8A
Upper Limit Instantaneous Current10A
Overcharge Voltage Range3.65V ± 0.05V
Over-discharge Voltage Range2.0V ± 0.05V
Quiescent CurrentLess than 30µA
Charging Voltage7.2V - 8.4V
ApplicationGeneral electronic applications (e.g., Computer related)
TypeVoltage Regulator

5. Troubleshooting

  • No Output/Charging: Check all wiring connections carefully, especially B+, B-, BM, P+, and P-. Ensure the battery pack voltage is within the operational range.
  • Short Circuit Protection Triggered: If a short circuit occurs, the board will cut off power. Remove the short circuit, and the board should self-recover after a short delay.
  • Battery Not Charging Fully: Verify the charging voltage is within the specified 7.2V-8.4V range. Ensure the charger can supply sufficient current.
  • Battery Discharging Too Quickly: Check for excessive load current. The board will trigger overcurrent protection if the load exceeds 8A continuous or 10A instantaneous.

6. User Tips

  • Verify Specifications: Always double-check the product specifications against your battery pack requirements (voltage, current, chemistry) to ensure compatibility.
  • Balancing Functionality: Be aware that while the product name includes 'Balance Charger Protect Module', some user feedback suggests this specific BMS model (HX-2S-D01) primarily provides protection and may not include active cell balancing. If cell balancing is critical for your application, consider a BMS explicitly advertised with active balancing features.
  • Quality and Functionality: Users have reported that the product is functional, of good quality, and corresponds to the description for its protection features.

7. Warranty and Support

For detailed warranty information or technical support, please refer to the seller's policies or contact the manufacturer directly. Additional technical documentation, including a user manual in PDF format, may be available for download from the seller's product page or by contacting support. You can find a PDF user manual at: HX-2S-D01 User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.