1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your DOOYA DM25TE Tubular Motor System. This system is designed to motorize blinds and shades, offering convenient control for various window types, including Roman shades and skylights. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.
2. Safety Instructions
- Ensure all electrical connections are made by a qualified electrician and comply with local regulations.
- Disconnect power before performing any installation, maintenance, or repair work.
- Keep children and pets away from the motorized blinds during operation.
- Do not allow children to play with fixed controls or remote controls.
- Regularly inspect the motor and blind for signs of wear or damage. Do not operate if damaged.
- This motor is designed for indoor use in dry conditions (IP44 rated). Avoid exposure to moisture or extreme temperatures.
- Do not attempt to modify or disassemble the motor or remote control.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation:
- DOOYA DM25TE Tubular Motor
- Remote Controller (may vary by specific kit)
- Installation Brackets and End Cap
- Instruction Manual (this document)
Figure 1: DOOYA DM25TE Tubular Motor with its specification label.
Figure 2: Included installation brackets and end cap.
4. Specifications
| Feature | Specification |
|---|---|
| Model | DM25TE |
| Motor Diameter | Ø 25mm (as per motor label) |
| Compatible Tube Diameter | 38mm (with appropriate adapters/brackets) |
| Torque (TEQ/L) | 0.7 Nm |
| Voltage | 100-240V AC |
| Frequency | 50/60Hz |
| Power | 7.02W |
| Current | 0.08A |
| Speed | 20 r/min |
| IP Rating | IP44 |
| Control Type | AC Electronic Radio (Remote Control) |
| Type | Roman Shades |
| Material | Metal |
| Installation Type | Exterior Installation |
| Applicable Window Type | Skylight |
| Opening and Closing Method | Upper Open |
5. Installation
5.1 Preparing the Blind Tube
- Ensure your blind tube has an inner diameter compatible with the motor (e.g., 38mm outer diameter tube with appropriate adapters for the 25mm motor).
- Cut the blind tube to the required length, accounting for the motor and end cap.
- Insert the motor into one end of the blind tube and the end cap into the other. Ensure they fit snugly.
5.2 Mounting the Brackets
- Determine the desired mounting location for your blind (Exterior Installation is specified).
- Mark the positions for the installation brackets (refer to Figure 2 for bracket design). Ensure they are level and correctly spaced to support the blind tube.
- Drill pilot holes and securely fasten the brackets to the wall or ceiling using appropriate screws and anchors.
5.3 Installing the Motorized Blind
- Carefully place the assembled blind tube (with motor and end cap) onto the installed brackets. Ensure the motor's power cable is accessible.
- Connect the motor's power cable to your electrical supply. Ensure the power is off during connection.
6. Operation
The DM25TE motor operates via a radio frequency (RF) remote control. The remote control allows you to raise, lower, and stop your blinds at any desired position.
6.1 Pairing the Remote Control
Refer to your remote control's specific instructions for pairing with the motor. Typically, this involves a short programming sequence on both the motor (often a button on the motor head or a power cycle) and the remote.
6.2 Basic Functions
- UP Button: Raises the blind.
- DOWN Button: Lowers the blind.
- STOP/MY Button: Stops the blind at its current position. Can often be programmed as a 'favorite' position.
6.3 Setting Limit Positions
Most tubular motors require setting upper and lower limit positions to prevent over-winding or over-extending the blind. Consult your remote control and motor's specific programming guide for instructions on how to set these limits. This usually involves pressing a combination of buttons on the remote while the blind is at the desired position.
7. Maintenance
- Cleaning: Wipe the motor and remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Remote Battery: If the remote control's range decreases or it becomes unresponsive, replace its batteries. Refer to the remote's manual for battery type and replacement procedure.
- Inspection: Periodically check the mounting brackets and blind fabric for any signs of wear, damage, or loose connections.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not respond to remote. | No power to motor; Remote batteries low/dead; Remote not paired; Obstruction. | Check power supply; Replace remote batteries; Re-pair remote (see section 6.1); Check for obstructions. |
| Blind stops unexpectedly. | Limit switch reached; Obstruction; Motor overheating. | Check limit settings; Remove obstruction; Allow motor to cool down. |
| Blind does not move smoothly. | Fabric snagging; Tube misalignment; Damaged motor/components. | Inspect blind fabric and guides; Re-align tube; Contact support if components are damaged. |
9. User Tips
- Tube Compatibility: Always verify the inner diameter of your blind tube matches the motor's requirements or that you have the correct adapters. For example, if using an IKEA Tupplur blind, you may need to change the tube as its diameter might be smaller than required.
- Blind Size: The 0.7 Nm torque of the DM25TE motor is suitable for light to medium-sized blinds. For very large or heavy blinds (e.g., 6m high and 3m wide), this motor may not be strong enough, and a motor with higher torque would be recommended.
- Remote Control: The DM25TE model includes a remote control for convenience. Ensure it is properly paired and its batteries are functional.
10. Warranty and Support
For warranty information or technical support, please refer to the seller's policies or contact the point of purchase. Keep your purchase receipt as proof of purchase.