Usongshine 17HS4401S

Contents

Usongshine Nema17 Stepper Motor 17HS4401S User Manual

Model: 17HS4401S

1. Introduction

This manual provides essential information for the safe and effective use of your Usongshine Nema17 Stepper Motor (Model 17HS4401S). Please read it thoroughly before installation and operation.

Overview of Usongshine Nema17 Stepper Motors with various cable types

Figure 1: Usongshine Nema17 Stepper Motors and included cables

2. Safety Information

  • Electrical Hazard: Stepper motors operate with electrical current. Ensure all connections are made correctly and securely. Always disconnect power before making or changing connections.
  • Mechanical Injury Hazard: The motor shaft rotates at various speeds. Keep hands, clothing, and other objects clear of the rotating shaft during operation to prevent entanglement or injury.
  • Overheating: Motors can become hot during prolonged operation, especially if current settings are too high. Avoid touching the motor directly after use. Ensure adequate ventilation.

3. Setup and Installation

3.1 Unpacking

Carefully remove the stepper motor and any accessories from the packaging. Inspect for any visible damage. If damage is found, contact your supplier immediately.

3.2 Mounting

The Nema17 motor features standard mounting holes for easy integration into your system (e.g., 3D printers, CNC machines). Use M3 screws for mounting.

Dimension diagram of Nema17 Stepper Motor with mounting hole details

Figure 2: Motor Dimensions (mm)

3.3 Wiring

The motor is a 2-phase hybrid stepper motor. It typically comes with a 4-pin cable (1 meter in length) with either a DuPont or XH-2.54 connector, depending on the variant. Connect the motor to a compatible stepper motor driver.

Nema17 Stepper Motor with XH-2.54 cable and cable length diagram

Figure 3: Motor with XH-2.54 Cable (approx. 100cm)

Refer to the electrical schematic for coil connections:

Electrical schematic for Nema17 Stepper Motor showing coil connections A, B, C, D

Figure 4: Electrical Schematic

Typically, these motors are wired as bipolar. Consult your stepper motor driver's manual for specific wiring instructions, matching the motor's coil pairs (e.g., A-C and B-D).

3.4 Driver Connection

A stepper motor driver is required to operate this motor. Drivers like the A4988 or DRV8825 are commonly used and compatible. Ensure the driver's current limit is set correctly to match the motor's rated current (1.5A per phase) to prevent overheating or underperformance.

4. Operating Instructions

The Nema17 stepper motor provides precise rotational control, ideal for applications requiring accurate positioning.

4.1 Power Supply

The motor operates on low voltage (below 50Vac or 75Vdc). Typical operating voltages for Nema17 motors range from 12V to 24V DC. Always ensure your power supply and driver are compatible with the motor's specifications.

4.2 Control

The motor is controlled via step and direction signals from a microcontroller or CNC controller, routed through the stepper motor driver. The step angle is 1.8 degrees per full step, allowing for fine control when microstepping is enabled on the driver.

Video 1: Demonstration of motor rotation with varying step distances (10mm, 0.1mm, 1mm).

4.3 Usage Restrictions

This motor is designed for general-purpose applications and is not intended for industrial continuous-duty operation. Observe the maximum duty cycle specified in your equipment manual. Do not use this motor for any purpose other than its intended design application.

5. Maintenance

  • Cleaning: Keep the motor free from dust and debris. Use a soft, dry cloth for cleaning. Avoid using liquids or solvents.
  • Environmental Conditions: Operate and store the motor indoors. Operating Temperature: 0°C to 40°C. Storage Temperature: -10°C to 50°C. The motor has an Ingress Protection Rating of IP20 (dust-protected, no water protection). Do not use in damp, dusty, corrosive-gas, or explosive environments.
  • Inspection: Periodically check wiring connections for looseness or damage. Ensure mounting screws are secure.

6. Troubleshooting

  • Motor Not Moving or Moving Incorrectly:
    • Check all wiring connections for correctness and security.
    • Verify the power supply is providing the correct voltage and current.
    • Ensure the stepper motor driver's current limit is set appropriately for the motor (1.5A per phase).
    • Confirm that the controller is sending correct step and direction signals.
  • Excessive Noise or Vibration:
    • Incorrect driver current settings are a common cause. Adjust the driver's current limit.
    • Ensure the motor is securely mounted and not vibrating against other components.
    • Consider using different stepper motor drivers (e.g., TMC2209 for quieter operation) if A4988 drivers are too noisy, after verifying current settings.
  • Motor Overheating:
    • The driver current limit may be set too high. Reduce the current.
    • Ensure the motor is not overloaded beyond its holding torque capacity.
    • Provide adequate ventilation around the motor.

7. Specifications

FeatureSpecification
Model Number17HS4401S (also 17HS4401)
TypeHYBRID
Step Angle1.8 degrees
Phase2
Current / Phase1.5A
Holding Torque42 N.cm
Cable Length1m
Plug TypeXH-2.54 (or DuPont, depending on variant)
EU LVD VoltageBelow 50Vac or 75Vdc
CertificationCE, ROHS
OriginMainland China

8. User Tips

  • Always use a dedicated stepper motor driver to control the motor. Common drivers like A4988 or DRV8825 are generally compatible.
  • Carefully adjust the driver's current limit to match the motor's 1.5A per phase. Incorrect settings can lead to excessive noise, vibration, or overheating.
  • Ensure your wiring is correct and secure. Most Nema17 motors are used in a bipolar configuration.
  • If you experience excessive noise, try different stepper drivers (e.g., TMC2209) or fine-tune your current settings.

9. Warranty and Support

For warranty information, technical support, or any issues not covered in this manual, please contact your original seller or the manufacturer directly. You may also refer to the official user manual PDF for additional details: View User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.