Glixal GY6 A9 Camshaft

Contents
Glixal Logo

Glixal GY6 High Angle Performance A9 Camshaft User Manual

Model: GY6 A9 Camshaft

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Glixal GY6 High Angle Performance A9 Camshaft. This camshaft is designed to enhance the performance of single-cylinder, 4-stroke, forced air-cooled GY6 series scooter engines, specifically 50cc, 80cc, and 100cc variants (139QMB, 139QMA, 152QMI, 157QMJ). It optimizes the opening and closing of intake and exhaust valves, leading to improved engine timing and overall performance.

The A9 camshaft features high-quality "XX" bearings for enhanced durability and reliability.

Glixal GY6 A9 Camshaft Top View

Figure 1: Glixal GY6 A9 Camshaft (Top View)

2. Safety Instructions & Warnings

  • Professional Installation Recommended: This product is a critical engine component. Improper installation can cause severe engine damage or personal injury. Installation should be performed by a qualified mechanic.
  • Engine Temperature: Ensure the engine is completely cool before starting disassembly to avoid burns.
  • Battery Safety: Disconnect the negative (-) battery terminal before working on the engine to prevent accidental starting.
  • Cleanliness: Maintain a clean working environment. Dirt or debris entering the engine can cause catastrophic failure.
  • Torque Specifications: Always use a torque wrench. Over-tightening or under-tightening bolts can lead to part failure.
  • Personal Protective Equipment (PPE): Wear safety glasses and gloves during installation.
  • Critical Compatibility Warning (139QMB with 52mm Piston): For 139QMB engines with a maximum diameter 52mm piston, installation of this camshaft may be impossible. The valves may contact the piston at Top Dead Center (TDC) during transient operation. Verify piston-to-valve clearance before installation.

3. Tools Required

  • Socket set and wrenches (8mm, 10mm, 12mm, 17mm)
  • Screwdrivers (Flathead and Phillips)
  • Torque Wrench
  • Feeler Gauge (for valve clearance adjustment)
  • Clean lint-free cloths
  • Engine Oil (for lubrication during assembly)
  • Gasket scraper (if replacing head gasket)

4. Installation

Step 1: Preparation

  1. Place the scooter on a center stand on a level surface.
  2. Disconnect the negative battery terminal.
  3. Remove the seat and floor cover to access the engine fan cover.
  4. Drain the engine oil into a suitable container.

Step 2: Access the Cylinder Head

  1. Remove the cooling fan cover and the CVT drive face cover.
  2. Remove the spark plug cap and the spark plug.
  3. Loosen and remove the bolts securing the cylinder head cover (rocker arm cover). Carefully lift the cover off. Note: Be careful not to lose the dowel pins or damage the gasket surface.

Step 3: Remove Old Camshaft

  1. Rotate the crankshaft (using a socket on the crank nut) until the "T" mark on the flywheel aligns with the index mark on the crankcase, and the camshaft sprocket marks are horizontal (Top Dead Center - TDC on compression stroke).
  2. Loosen the rocker arm adjusting nuts and push the rocker arms aside to release tension.
  3. Remove the bolts securing the camshaft sprocket.
  4. Carefully remove the timing chain from the sprocket.
  5. Unbolt the camshaft holder/caps. Tip: Loosen bolts in a crisscross pattern evenly to prevent warping.
  6. Lift out the old camshaft assembly.

Step 4: Install New Camshaft Assembly

  1. Clean the cylinder head surface and the camshaft journals thoroughly.
  2. Apply a thin layer of fresh engine oil to the new camshaft lobes and journals.
  3. Place the new camshaft into the cylinder head, ensuring the alignment pins fit correctly.
  4. Reinstall the camshaft holder/caps. Tighten the bolts evenly in a crisscross pattern to the manufacturer's specified torque (typically 8-10 N·m, please verify with specific engine manual).
  5. Reattach the timing chain to the sprocket. Ensure the timing marks on the sprocket align horizontally with the cylinder head surface while the crankshaft remains at the "T" mark.
  6. Secure the sprocket bolts to the specified torque.
Glixal GY6 A9 Camshaft with Bearings

Figure 2: Glixal GY6 A9 Camshaft showing bearings

Step 5: Valve Clearance Adjustment (Critical)

  1. Ensure the engine is still at TDC (Compression Stroke).
  2. Use a feeler gauge to check the gap between the rocker arm and the valve stem.
  3. Typical Valve Clearances:
    • Intake Valve Clearance: 0.08mm - 0.12 mm
    • Exhaust Valve Clearance: 0.10 mm - 0.14 mm
    (Refer to your specific scooter's service manual for exact values)
  4. Loosen the lock nut, turn the adjusting screw until the correct drag is felt on the feeler gauge, then tighten the lock nut while holding the screw. Re-check the clearance.

Step 6: Reassembly

  1. Clean the cylinder head cover mating surface. Install a new gasket if necessary.
  2. Reinstall the cylinder head cover and tighten bolts evenly.
  3. Reinstall the spark plug and connect the cap.
  4. Reassemble the CVT covers and fan shroud.
  5. Refill the engine with the recommended amount and grade of oil (usually 10W-30 or 10W-40, approx. 750ml-900ml depending on the model).
  6. Reconnect the battery.

Step 7: Testing

  1. Start the engine and let it idle for a few minutes. Listen for abnormal noises (ticking or knocking).
  2. Check for oil leaks around the cylinder head cover.
  3. Take a short test ride. Re-check valve clearances after the engine has cooled down again (optional but recommended for precision).

5. Operation

The Glixal GY6 High Angle Performance A9 Camshaft is designed to alter the valve lift and duration, optimizing the engine's breathing characteristics. This results in improved volumetric efficiency, leading to a noticeable increase in horsepower and torque, especially in the mid to high RPM range. Users can expect a more responsive throttle and enhanced acceleration compared to a standard camshaft.

While some users report significant gains, the exact performance improvement can vary based on other engine modifications and tuning. Proper installation and valve clearance adjustment are crucial to realize the full benefits of this performance camshaft.

6. Maintenance & Disposal

  • Inspection: Inspect valve clearance every 6,000 km or annually.
  • Oil Change: Regular oil changes are crucial for camshaft longevity.
  • Disposal: Dispose of old parts and waste oil according to local environmental regulations. Do not throw engine oil into drains or soil.

Note: Always refer to your scooter's official service manual for model-specific torque values and maintenance schedules.

7. Troubleshooting

  • No significant performance improvement after installation:
    • Verify that the camshaft is correctly installed and aligned.
    • Double-check valve clearances as per your scooter's service manual. Incorrect clearances can severely impact performance.
    • Ensure your engine is fully compatible with the A9 camshaft.
  • Abnormal engine noises (ticking/knocking) after installation:
    • Immediately shut off the engine.
    • Re-check valve clearances.
    • Ensure all bolts, especially those for the camshaft holder/caps and sprocket, are torqued to specification.
    • Confirm the timing chain is correctly installed and tensioned.
  • Oil leaks around the cylinder head:
    • Ensure the cylinder head cover gasket is properly seated and not damaged.
    • Verify that the cylinder head cover bolts are tightened evenly and to the correct torque.

8. Specifications

Attribute Value
Brand Name Glixal
Model Name GY6 A9
Item Type Engines (Camshaft)
Displacement (ml) 50cc, 80cc, 100cc
No. of Cylinders 1 Cylinder
Stroke 4 Stroke
Engine Model Compatibility 139QMB, 139QMA, 152QMI, 157QMJ
Material Alloy
Item Weight 0.35kg
External Testing Certification ISO9001
Product Condition New
Used for Chinese Scooter, Moped, ATV (Baotian, Taotao, Jonway, VIP, ZNEN, Kymco, Roketa, Sunl, Tank, TNG, Tenko, Nitro, Vento, etc.)
Diagram of compatible engine types and scooter models

Figure 3: Compatible Engine Types and Scooter Models

9. User Tips

  • Many users report a noticeable improvement in performance and throttle response compared to stock camshafts.
  • The product is generally regarded as having good quality, with improved bearings ("XX" type) compared to previous versions.
  • Ensure precise valve clearance adjustment for optimal performance and engine longevity. While typical values are provided, always cross-reference with your specific scooter's service manual.
  • Confirmed compatibility and performance on various Chinese scooters and mopeds, including Kymco KG10SA.

10. Warranty & Support

Glixal strives for 100% customer satisfaction. If you receive an incorrect, damaged, defective, or an item not as described, please contact the seller within 7 days of receipt for assistance.

For further detailed information, including specific torque values and advanced troubleshooting, please refer to the official user manual PDF available at Glixal GY6 Camshaft User Manual (PDF).

11. Manufacturer Information

Manufacturer: YIWU SHENGQI IMP&EXP CO.,LTD
Unit 2, Building 71, Gongdatang No.1 District, Yiwu City, Zhejiang Province
Email: atmotorparts@outlook.com

EU Authorized Representative: SUCCESS COURIER SL
CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3
Fuenlabrada, Madrid, 28947 Spain
Tel: 910602659

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.