SHIMANO MT420

Contents

SHIMANO DEORE MT420 Hydraulic Disc Brake Set

Model: MT420 | Brand: SHIMANO

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your SHIMANO DEORE MT420 Hydraulic Disc Brake Set. This set includes BL-MT401 brake levers and BR-MT420 4-piston brake calipers, designed for mountain bike applications. Please read this manual thoroughly before use and retain it for future reference.

2. Safety Information

⚠ Warning Symbol & Notice

  • This product is not a toy and is not suitable for children under 16 years old without adult supervision. Keep all small parts (e.g., screws) away from infants and toddlers to avoid choking hazards.
  • Always wear appropriate protective gear (helmet, gloves, knee pads) when operating the bicycle with this brake system. Do not use the product in traffic without proper training.
  • Ensure the brake system is correctly installed and adjusted before use. Improper installation may cause braking failure, leading to falls or serious injury.
  • Do not modify the brake system's structure or components. Unauthorized modifications void compliance and safety guarantees.
  • This product is not intended for use with children's bicycles (refer to EN 14765 for children-specific requirements).
  • Keep the brake system away from corrosive substances (acids, solvents) and extreme temperatures to prevent mechanical failure.

Additional Safety Notes:

  • Regularly inspect the brake system for wear, damage, or loose connections. Replace worn parts immediately using genuine Shimano accessories.

3. Product Overview and Components

The SHIMANO DEORE MT420 Hydraulic Disc Brake Set consists of the following main components:

  • BL-MT401 Brake Levers: Ergonomically designed levers for precise control.
  • BR-MT420 Brake Calipers: 4-piston calipers providing strong and consistent braking power.
  • Hydraulic Hoses: Pre-bled and connected (or split for custom routing) hoses for fluid transfer.
  • Mounting Hardware: Bolts and clips for secure installation.
SHIMANO DEORE MT420 Hydraulic Disc Brake Set

Figure 1: Overview of the SHIMANO DEORE MT420 Hydraulic Disc Brake Set, showing both brake levers (BL-MT401), 4-piston calipers (BR-MT420), and connected hydraulic hoses. Available in split or connected configurations.

SHIMANO MT420 Brake Set with hose lengths

Figure 2: The MT420 brake set indicating typical hose lengths: left front 900mm and right rear 1600mm.

Close-up of SHIMANO BL-MT401 Brake Lever

Figure 3: Detail view of the BL-MT401 brake lever, showing the SHIMANO branding and "MINERAL OIL" designation.

Close-up of SHIMANO BR-MT420 Brake Caliper

Figure 4: Detail view of the BR-MT420 4-piston brake caliper, highlighting the "MALAYSIA VIA BR-MT420" markings.

SHIMANO MT420 Brake Mounting Hardware

Figure 5: Included mounting hardware, consisting of bolts and clips for securing the brake system components.

4. Setup and Installation

Professional installation by a qualified bicycle mechanic is highly recommended for hydraulic disc brakes. Incorrect installation can lead to serious injury or death. If you choose to install yourself, proceed with extreme caution and consult detailed technical documents from Shimano.

  1. Prepare Your Bicycle: Ensure your bicycle is clean and stable, preferably on a repair stand.
  2. Mount Brake Levers: Attach the BL-MT401 brake levers to your handlebars. The left lever typically controls the front brake, and the right lever controls the rear brake. Adjust their position for comfortable reach and ergonomics.
  3. Mount Brake Calipers: Secure the BR-MT420 calipers to your bike's frame and fork using the appropriate mounting hardware (Figure 5). Ensure the calipers are aligned correctly with your disc rotors.
  4. Route Hydraulic Hoses: Carefully route the hydraulic hoses along your bike's frame, securing them with clips to prevent snagging or interference with moving parts. The typical hose lengths are left front 900mm and right rear 1600mm (Figure 2).
  5. Connect Hoses (if split): If your brake set came with split hoses, connect them to the levers and calipers according to Shimano's instructions. This usually involves cutting the hose to length, installing olives and inserts, and tightening the connections.
  6. Bleed the System: Hydraulic disc brakes require proper bleeding to remove air from the system and ensure optimal performance. Follow Shimano's official bleeding procedure for hydraulic disc brakes. This is a critical step for brake safety and performance.
  7. Adjust Brake Pads: Ensure brake pads are correctly seated and have proper clearance from the rotor.
  8. Test Brakes: Before riding, thoroughly test the brakes at a slow speed in a safe area. Check for firm lever feel, consistent braking power, and no rubbing.
Installed SHIMANO Brake Lever on Handlebar

Figure 6: An example of the SHIMANO brake lever installed on a bicycle handlebar, demonstrating typical mounting position.

Installed SHIMANO Brake Caliper on Bicycle Wheel

Figure 7: An example of the SHIMANO brake caliper installed on a bicycle's front wheel, showing its position relative to the disc rotor.

5. Operating Instructions

To operate your SHIMANO DEORE MT420 Hydraulic Disc Brakes:

  1. Brake Application: Gently squeeze the brake levers to apply braking force. The amount of force applied to the lever directly correlates to the braking power.
  2. Modulation: Practice modulating your braking force to control your speed smoothly and effectively. Avoid sudden, hard braking unless in an emergency.
  3. Front vs. Rear Brake: The front brake (left lever) provides most of the stopping power. The rear brake (right lever) helps with stability and fine-tuning speed. Use both brakes in conjunction for optimal control and safety.
  4. Wet Conditions: In wet conditions, braking performance may be reduced. Apply brakes earlier and more gently to account for reduced traction.

6. Maintenance

Proper maintenance ensures the longevity and safe operation of your brake system.

  • Regular Inspection: Inspect the brake system every 500km or 3 months, whichever comes first. Check for wear, damage, or loose connections on levers, calipers, hoses, and pads.
  • Brake Pad Replacement: Replace brake pads when they are worn down to their minimum thickness or if they become contaminated. Always use genuine Shimano replacement pads.
  • Rotor Inspection: Check disc rotors for wear, damage, or warping. Replace if necessary. Keep rotors clean and free of oil or grease.
  • Hydraulic Fluid: The brake system uses mineral oil. Check fluid levels and bleed the system if the lever feel becomes spongy or inconsistent. Only use genuine Shimano mineral oil.
  • Cleaning: Clean the brake components with a mild soap and water solution. Avoid using harsh chemicals or solvents that could damage seals or paint.
  • Environmental Restrictions: Do not use in saltwater environments (e.g., coastal areas) without proper corrosion protection.

7. Troubleshooting

Here are some common issues and their potential solutions:

Problem Possible Cause Solution
Brake Overheating Prolonged heavy braking, undersized rotors. Ensure correct rotor size for your riding style. Avoid continuous heavy braking.
Poor Braking Power Air in system, worn pads, contaminated pads/rotor, misaligned caliper. Bleed the hydraulic system. Replace worn pads. Clean pads/rotor with disc brake cleaner. Realign caliper.
Inconsistent/Spongy Lever Feel Air in the hydraulic system. Bleed the hydraulic system thoroughly.
Brake Noise (Squealing/Grinding) Contaminated pads/rotor, worn pads, misaligned caliper, loose bolts. Clean pads/rotor. Replace worn pads. Realign caliper. Check all bolts are tightened to spec.
Levers are different colors (cosmetic) Manufacturing variation. This is a cosmetic issue reported by some users and does not affect performance.

8. Specifications

Feature Detail
Brand Name SHIMANO
Model Number MT420 (BL-MT401 Lever, BR-MT420 Caliper)
Type Hydraulic Disc Brake
Use Mountain Bikes
Material Light Alloy
Braking System Hydraulic Disc Brake (Hydraulic Brake Pad)
Components Caliper Brake
Pistons 4-Piston Caliper
Origin Japan (Jp)
High-concerned chemical None
Approximate Weight 561.0g (complete set, Figure 6)
Hose Lengths (Typical) Left Front: 900mm, Right Rear: 1600mm (Figure 2)

Usage Restrictions:

  • Not suitable for children under 16 years old (without adult supervision).
  • Not suitable for electric bicycles with motor power exceeding 250W.
  • Not recommended for off-road use in extreme conditions (e.g., rock climbing, steep descents >30°).
  • Not recommended for use in saltwater environments without proper corrosion protection.

9. User Tips

  • Bleeding is Key: Proper bleeding of the hydraulic system is crucial for optimal braking performance and a firm lever feel. If you experience a spongy lever, re-bleed the system.
  • Rotor Compatibility: Ensure you use disc rotors of appropriate size and material for your riding style and terrain to prevent overheating and maintain consistent braking power.
  • Check for Cosmetic Consistency: While not affecting performance, some users have noted variations in lever paint finish (e.g., one lever painted, the other unpainted). This is a cosmetic observation.
  • Excellent Braking Power: The SHIMANO DEORE MT420 system is known for providing excellent braking power and control, especially beneficial for mountain biking on varied terrain.

10. Compliance and Manufacturer Information

Applicable Regulations & Harmonized Standards:

This product complies with the following EU regulations and standards:

  • General Product Safety Directive (GPSD): 2001/95/EC
  • Mechanical Directive (MD): 2006/42/EC
  • Harmonized Standards:
    • EN ISO 4210-2:2015 (Bicycle safety requirements for city, trekking, mountain bikes)
    • EN 14781:2015 (Racing bicycle specific safety standards)
    • REACH Regulation (EC) No 1907/2006 (Restriction of hazardous substances)

EU Declaration of Conformity (DoC):

This product (Bicycle Part, Model: Universal Fit for Road/Gravel/MTB/E-Bike) meets the essential requirements of EU Directive 2006/42/EC (Mechanical Directive) and related harmonized standards. A complete copy of the DoC is available upon request from the EU Responsible Person.

Manufacturer Information:

Name: Yiwu Xiayi Bicycle Parts Co., Ltd.

Address: No. 8, Danchen 1st Road, Beiyuan Street, Yiwu City, Zhejiang Province

EU Responsible Person (Authorized Representative):

Name: MJCM SARL

Country: France

Address: 78 avenue des Champs Elysees, Bureau 326, 75008 Paris, France

Phone: +33-752907452

Email: mjcm190928@gmail.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.