diymore 15KV High Voltage Arc Ignition Generator

Contents

15KV High Frequency DC High Voltage Arc Ignition Generator Inverter Boost Transformer

Model: 15KV High Voltage Arc Ignition Generator | Brand: diymore

1. Introduction

This manual provides instructions for assembling and operating the diymore 15KV High Frequency DC High Voltage Arc Ignition Generator Inverter Boost Transformer DIY Kit. This kit is designed for educational purposes, high school science experiments, electronic equipment, negative ion generators, and small-scale scientific productions. It generates a stable, high-frequency, high-temperature arc capable of igniting combustible materials, often referred to as a plasma lighter.

The kit is available in two variants: with a PCB board or without a PCB board. Please refer to the relevant sections for your specific kit type.

2. Safety Information

WARNING: This device generates high voltage (approximately 15KV) and high temperatures. Improper use can cause serious injury or damage to equipment. Always exercise extreme caution when handling high voltage components.

  • Ensure all connections are secure before applying power.
  • Do not touch any components while the device is powered on.
  • Keep away from flammable materials during operation.
  • Operate in a well-ventilated area.
  • Adult supervision is recommended for educational use.
  • A higher output voltage than the specified 15KV limit can damage the transformer.

3. Package Contents

The kit includes the following components. Please verify all parts are present before beginning assembly.

Overview of components for both with and without PCB board versions
Figure 3.1: Overview of components for both 'with board' and 'without board' versions.
Close-up of the 15KV step-up transformer
Figure 3.2: Close-up of the 15KV step-up transformer.

Common Components:

  • 1 x 15VKE type step-up transformer
  • 1 x 120 ohm resistor
  • 1 x UF4007 ultra-fast recovery diode
  • 1 x N20 transistor
  • 1 x Heat sink
  • 1 x M3 * 6 screw
  • 1 x Boat switch
  • 1 x 3-Pin connector

Variant Specific Components:

  • With PCB Board: 1 x PCB Board
  • Without PCB Board: No PCB board included (components are wired directly)
Components for the 'with board' version
Figure 3.3: Components for the 'with board' version.
Components for the 'without board' version
Figure 3.4: Components for the 'without board' version.

4. Specifications

Parameter Value
Transformer Dimensions (approx.) 27mm × 16mm × 21mm
Input Voltage DC 3.7V-4.2V (Limit 12V, not recommended for prolonged use at 12V due to potential damage)
Input Current <2A
Output Voltage Approx. 15KV
Output Current ≤0.4A
High Voltage Bipolar Ignition Distance ≤0.5 cm
Transformer Structure Two primary windings (one primary, one feedback), one secondary high-pressure output

5. Setup Instructions (DIY Assembly)

This is a DIY kit and requires assembly. Soldering skills are necessary. Please follow the steps carefully based on whether your kit includes a PCB board or not.

5.1. Assembly with PCB Board

Refer to Figure 5.1 for component placement on the PCB.

  1. Identify Components: Lay out all components and identify them according to the package contents list.
  2. Resistor and Diode: Solder the 120 ohm resistor (R1) and the UF4007 ultra-fast recovery diode (D1) onto the PCB in their designated positions. Pay attention to the diode's polarity (banded end).
  3. Transistor and Heat Sink: Attach the N20 transistor to the heat sink using the M3*6 screw. Ensure the transistor is securely fastened to the heat sink for proper thermal management.
  4. Solder Transistor: Solder the transistor with the attached heat sink onto the PCB. As shown in Figure 5.2, ensure the transistor faces forward, and its back posts are aligned with the heat sink.
  5. Transformer Connections: Connect the 15KV step-up transformer to the PCB. The transformer has two primary windings (input) and one secondary winding (output). The primary windings connect to the PCB's input terminals, and the feedback winding connects to the designated feedback points. The high-voltage output wires should be kept separate and insulated.
  6. Boat Switch: Solder the boat switch to the designated power input points on the PCB.
  7. 3-Pin Connector: Solder the 3-pin connector to the appropriate terminals on the PCB, typically for power input or control.
  8. Power Input: Connect your DC 3.7V-4.2V power source to the boat switch or the 3-pin connector, ensuring correct polarity.
Components for the 'with board' version, showing PCB layout
Figure 5.1: Components for the 'with board' version, showing PCB layout.
Detailed assembly step showing transistor and heatsink placement on the PCB
Figure 5.2: Detailed assembly step showing transistor and heatsink placement on the PCB. Note: "Face forward, back posts on the heat sink."

5.2. Assembly without PCB Board

For kits without a PCB board, components must be wired directly. This requires a good understanding of circuit diagrams and careful soldering.

  1. Identify Components: Lay out all components and identify them.
  2. Wiring Diagram: Refer to the provided circuit diagram (if available, or a standard ZVS driver circuit for 15KV transformers) for correct wiring.
  3. Transformer Connections: Connect the primary windings of the 15KV transformer to the power input and the feedback winding to the transistor circuit.
  4. Transistor and Heat Sink: Attach the N20 transistor to the heat sink using the M3*6 screw. Wire the transistor into the circuit, ensuring proper connections for base, collector, and emitter.
  5. Resistor and Diode: Wire the 120 ohm resistor and the UF4007 diode into the circuit as per the diagram. Pay attention to the diode's polarity.
  6. Boat Switch and 3-Pin Connector: Integrate the boat switch for power control and the 3-pin connector for power input into your wiring.
  7. Insulation: Ensure all high-voltage connections are properly insulated to prevent short circuits and accidental contact.
  8. Power Input: Connect your DC 3.7V-4.2V power source, observing polarity.
Components for the 'without board' version
Figure 5.3: Components for the 'without board' version, requiring direct wiring.

6. Operating Instructions

  1. Power Source: Connect a DC power source within the 3.7V-4.2V range to the input terminals. Ensure correct polarity.
  2. Activation: Flip the boat switch to the 'ON' position.
  3. Arc Generation: When powered, the device will generate a high-frequency, high-temperature arc between the high-voltage output terminals (if not connected to rectifier diodes and capacitors). The arc may appear purple and produce a high temperature, capable of igniting paper or thin wires.
  4. Arc Distance: The high voltage bipolar ignition distance is approximately ≤0.5 cm.
  5. Deactivation: To turn off the device, flip the boat switch to the 'OFF' position and disconnect the power source.

Always maintain a safe distance from the high-voltage output terminals during operation.

7. Maintenance

  • Keep the device clean and free from dust and debris.
  • Store in a dry environment away from moisture.
  • Regularly inspect connections for any signs of wear or damage.
  • Ensure the heat sink is clear of obstructions to allow for proper cooling of the transistor.

8. Troubleshooting

Common Issues:

  • No Arc/Weak Arc:
    • Check power supply voltage and current. Ensure it's within the 3.7V-4.2V range and can supply sufficient current (<2A).
    • Verify all connections are secure and correctly soldered.
    • Check the polarity of the diode and transistor.
    • Inspect the transformer windings for any damage.
  • Transistor Overheating/Burning Out:
    • Ensure the heat sink is properly attached to the transistor and is effective in dissipating heat.
    • Critical User Tip: The 120 ohm bias resistor included in the kit might be too low for some setups, leading to excessive current draw and transistor failure. Consider replacing it with a higher value resistor, such as 10k to 12k ohm, if you experience repeated transistor burnout.
    • Verify there are no shorts between the primary and secondary windings of the transformer.
  • Unstable Arc:
    • Check for loose connections or poor soldering joints.
    • Ensure the power supply is stable.

9. User Tips

  • Resistor Value: If you encounter issues with the transistor burning out, consider experimenting with a higher value for the bias resistor (e.g., 10k to 12k ohm) instead of the default 120 ohm resistor. This can help prevent excessive current draw.
  • Power Supply: While the kit can technically handle up to 12V input, it is strongly recommended to stick to the 3.7V-4.2V range to prevent damage to the transformer and other components.
  • Experimentation: This kit is ideal for learning about high voltage generation. Always proceed with caution and research relevant safety practices.

10. Frequently Asked Questions (FAQ)

Q: Is this kit suitable for beginners?
A: Basic soldering skills and an understanding of electronic components are recommended. Always follow safety guidelines.
Q: What kind of power source should I use?
A: A DC power source providing 3.7V-4.2V with sufficient current capacity (e.g., a fully charged 18650 battery or a regulated power supply) is ideal.
Q: Can I modify the circuit?
A: Modifications are at your own risk and may void any implied functionality. Always understand the circuit thoroughly and prioritize safety if making changes.

11. Warranty and Support

As a DIY kit, specific warranties may vary. For detailed information or additional guides, please refer to the official product documentation. A user manual in PDF format may be available for further reference:

View User Manual (PDF)

For technical support or inquiries, please contact the seller directly through the platform where the product was purchased.

© 2024 diymore. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.