User Manual

1. Introduction

Thank you for choosing the Cltgxdd BX-180 IEC320 C8 Power Inlet Socket. This manual provides essential information for the safe and effective use of your product. Please read it thoroughly before installation and keep it for future reference.

Figure 1: Cltgxdd BX-180 IEC320 C8 Power Inlet Sockets (Black and White)

Play video

Video 1: Product Overview of the IEC320 C8 Power Inlet Socket

2. Safety & Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

• Warning: Keep the device and its cord (if applicable) out of reach of children under 3 years old.
• Keep away from children unless supervised by an adult.
• Do not use this product for purposes other than its intended use.
• Inspect the product before each use; do not use if damaged.
• Follow installation and operation guidelines to avoid injury.
• Do not expose to water or moisture.
• Handle with care to avoid cuts or injuries.
• Keep away from fire and high temperature.

3. Package Contents

Your package should contain:

• 1 x Cltgxdd BX-180 IEC320 C8 Power Inlet Socket (Color as selected)

4. Specifications

Dimensions:

Figure 2: Dimensional Diagram of the BX-180 Socket

• Overall Front Panel (L x W): 28 mm x 16 mm
• Mounting Hole Spacing (Center-to-Center): 26 mm
• Body Depth (from front panel): 14 mm
• Terminal Length: 8 mm
• Terminal Spacing (Center-to-Center): 7 mm
• Recommended Panel Cutout (Approx.): 26 mm x 14 mm

5. Setup and Installation

5.1 Before First Use

• Remove all protective films or packaging materials from the device.
• Inspect the socket for any visible damage. Do not use if damaged.

5.2 Installation Steps

This power inlet socket is designed for panel embedding. Ensure all power is disconnected before beginning installation.

1. Prepare Panel: Create a rectangular cutout in your device panel according to the recommended dimensions (approximately 26 mm x 14 mm). Ensure the panel thickness is suitable for the socket's mounting tabs.
2. Insert Socket: Gently push the socket into the cutout from the front of the panel until the mounting tabs snap into place, securing the socket.
3. Wire Connections: Connect your internal wiring to the two terminals on the rear of the socket. Ensure secure connections. For soldering, refer to the operating instructions below.

Figure 3: Rear View of Socket with Terminals

6. Operating Instructions

Once installed and wired, the BX-180 socket functions as a standard IEC320 C8 power input. Connect a compatible C7 power cord to supply power to your device.

6.1 Soldering Guidelines (if applicable)

If you are soldering wires to the terminals:

• Control temperature and time during soldering to avoid damage from high temperature to the socket's plastic housing or internal components.
• Use appropriate soldering techniques to ensure a strong, reliable electrical connection.

6.2 Power Considerations

• Do not exceed the rated voltage (AC 250V) or current (2.5A) to avoid burnout or failure of the socket or connected device.
• Ensure the power supply and connected device are compatible with the socket's ratings.

7. Maintenance

The Cltgxdd BX-180 power inlet socket requires minimal maintenance.

• Cleaning: If necessary, gently wipe the exterior of the socket with a dry, soft cloth. Do not use abrasive cleaners or solvents.
• Storage (if not installed): Store the device in a dry place, away from direct sunlight and extreme temperatures. Keep away from children.
• Inspection: Periodically inspect the socket and its connections for any signs of wear, damage, or loose wiring. Address any issues promptly.

8. Troubleshooting

If you experience issues with the power inlet socket, consider the following:

• No Power to Device:
  • Check if the C7 power cord is fully inserted into the socket.
  • Verify that the power cord is functional and connected to a live power outlet.
  • Inspect the internal wiring connections to the socket for looseness or damage.
  • Ensure the socket itself is not damaged.
• Loose Connection:
  • If the C7 power cord feels loose in the socket, inspect the socket for any physical damage or deformation.

For persistent issues, consult a qualified electrician or technician.

9. User Tips

• Always ensure proper polarity when wiring, even for non-polarized sockets, to maintain consistency in your device's internal circuitry.
• When soldering, use heat shrink tubing over exposed terminal connections for added insulation and strain relief.
• Double-check all connections before applying power to prevent short circuits or damage.

10. Warranty and Support

For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Manufacturer: Shenzhen Yisailun Electronic Technology Co., Ltd.