Heltecbms 0855A

Contents

Heltecbms 5A Capacitive Active Balancer User Manual

Model: 0855A Series

1. Introduction

This Heltecbms 5A Capacitive Active Balancer is designed for ternary lithium, lithium iron phosphate (LiFePO4), and lithium titanate (LTO) batteries. It is specifically engineered for charging and discharging large-capacity series-parallel battery packs. Unlike inductive balancers, this capacitive balancer achieves a whole-group balance without requiring a voltage difference between adjacent batteries to initiate balancing. This functionality effectively protects the battery circuit, enhancing the safety and reliability of your battery pack.

Key features include a maximum balance current of 5.5A, whole-group balancing, automatic low-voltage sleep protection, and temperature protection.

2. Setup and Installation

2.1. Precautions for Use

  • Wiring Sequence: Before connecting or removing the balancer from the battery, ensure the wiring sequence is correct. Incorrect connections will damage the balancer and battery.
  • Protection: Ensure adequate insulation, heat dissipation, and anti-static protection during use. When testing, installing, or touching the balancer, always take appropriate protective measures.
  • Component Handling: Avoid touching circuit board components with lead wires, soldering irons, or tin slag, as this may damage the balancer.
  • Placement: When connecting to the battery pack, the balancer must be placed on the surface of an insulating material outside the battery pack. Do not place it directly on the battery for balancing.
  • Usage Conditions: Always adhere to the design parameters and usage conditions specified in this manual. Operating outside these parameters can damage the balancing board and the battery pack.
  • Abnormalities: If any abnormality occurs during use, immediately stop using the device and contact professional maintenance personnel or the manufacturer for repair.

2.2. Connector Definition

ConnectorNameDefinition
ARUNDefault is shorted. An external switch can be connected to control the balance function.
B- ~ Bn+B-Negative pole of the 1st string (total)
B1+Positive pole of the 1st string
B2+Positive pole of the 2nd string
B3+Positive pole of the 3rd string
B4+Positive pole of the 4th string
B5+Positive pole of the 5th string
Bn+Positive pole of the nth string (final)
CLTO/(from left to right)

2.3. Battery Type Mode Selection

The balancer supports different battery chemistries (LTO, NCM, LFP). You must configure the balancer for your specific battery type by soldering specific pads on the board.

  • For LTO (Lithium Titanate) battery: Solder pads 1 and 2 together.
  • For NCM and LFP (Ternary Lithium/Lithium Iron Phosphate) battery: Solder pads 2 and 3 together.

Note: The circuit solder joints for mode selection (RUN) are strictly prohibited from being soldered together with RUN. This will cause a short circuit and damage the balancer.

Diagram showing solder points for LTO and NCM/LFP battery type selection.

Figure 1: Battery Type Selection Solder Points

2.4. Wiring Diagrams

Connect the balancer to your battery pack according to the specific string configuration. Ensure all connections are secure and follow the polarity indicated in the diagrams. The RUN indicator light shows continuous working status; it will turn off only during under-voltage protection or balancer failure.

Wiring diagram for 3S and 4S battery configurations.

Figure 2: Wiring for 3S and 4S Battery Packs

Wiring diagram for 7S and 8S battery configurations.

Figure 3: Wiring for 7S and 8S Battery Packs

Wiring diagram for 11S and 13S battery configurations.

Figure 4: Wiring for 11S and 13S Battery Packs

Wiring diagram for 12S and 14S battery configurations.

Figure 5: Wiring for 12S and 14S Battery Packs

Wiring diagram for 16S and 18S battery configurations.

Figure 6: Wiring for 16S and 18S Battery Packs

Wiring diagram for 20S and 21S battery configurations.

Figure 7: Wiring for 20S and 21S Battery Packs

2.5. Optional Acrylic Case Assembly

An acrylic protective case is available for each model to provide physical protection for the balancer board. The case typically includes acrylic plates, screws, and standoffs.

Components for assembling the acrylic protective case.

Figure 8: Acrylic Case Components

To assemble the case:

  1. Place the balancer board onto one acrylic plate, aligning the screw holes.
  2. Secure the board using the provided standoffs and screws.
  3. Attach the second acrylic plate on top, securing it with the remaining screws.
Image of the balancer board with an acrylic case.

Figure 9: Balancer with Acrylic Case

3. Operating Instructions

3.1. Basic Principle

The balancer operates on the principle of capacitor fit charge transfer. Once connected to the battery, it automatically begins equalization. The maximum equalizing voltage difference is 0.01V. When the voltage difference between cells is 0.1V, the current is approximately 0.5A (this current can vary based on battery capacity and internal resistance). The greater the differential voltage, the higher the equalization current. As the battery becomes more balanced, the working current decreases.

3.2. Automatic Operation and Protection

  • Automatic Start: The balancer starts equalizing automatically once connected to the battery pack.
  • Low-Voltage Sleep: The balancer will automatically stop working and enter a sleep state when the voltage drops below a certain threshold:
    • 3.0V for NCM/LFP batteries.
    • 1.8V for LTO batteries.
    In sleep mode, the standby power consumption is less than 0.1mA.
  • Manual Sleep Switch: Some models may include a manual sleep switch. When activated, the sleep current mode is less than 0.1mA.

3.3. Optional Voltage Display Module

A TFT-LCD display module (for 4S, 6S, 8S versions) can be connected directly to the battery in parallel with the balancer or protection board. This module displays the voltage of each string and the total voltage of the pack. The typical accuracy is ±5mV at room temperature (25°C) and ±8mV across a wide temperature range (-20°C to 60°C).

Image of the balancer with an optional voltage display module.

Figure 10: Balancer with Optional Voltage Display

4. Maintenance

  • General Care: Keep the balancer clean and free from dust and debris. Avoid exposing it to excessive moisture or extreme temperatures.
  • Physical Protection: If using an acrylic case, ensure it is properly assembled and secured to protect the circuit board from physical damage.
  • Storage: When not in use for extended periods, store the balancer in a dry, cool environment.

5. Troubleshooting

  • Balancer Not Operating: Check all wiring connections for correctness and secure contact. Ensure the battery pack voltage is above the low-voltage sleep threshold.
  • Abnormal Behavior: If the balancer exhibits any unusual behavior (e.g., excessive heat, smoke, incorrect balancing), immediately disconnect it from the battery pack.
  • Professional Assistance: For any persistent issues or malfunctions, stop using the device and contact professional maintenance personnel or Heltecbms support for assistance.

6. Specifications

ParameterSpecification
Product Models0855A, 1004A, 0877A, 1400, 0999A16, 1323
Applicable String Number3S-4S, 4S-6S, 6S-8S, 9S-14S, 12S-16S, 17S-21S
Applicable Battery TypeNCM/LFP/LTO
Working Voltage Range (NCM/LFP)2.7V - 4.2V
Working Voltage Range (LTO)1.8V - 3.0V
Voltage Equalization Accuracy5mV (typical)
Balanced ModeWhole battery group participates in active energy transfer equalization
Equalizing Current0.08V differential voltage generates 1A balance current. Max 5.5A.
Under Voltage Protection Sleep Voltage (NCM/LFP)3.0V
Under Voltage Protection Sleep Voltage (LTO)1.8V
Static Working Current8mA - 17mA (model dependent)
Working Environment Temperature-10°C to 60°C
External PowerNot required (relies on internal energy transfer)
Recommended Battery Capacity60-300AH

7. User Tips

  • Complementary to BMS: This active balancer works very effectively when paired with inexpensive or basic Battery Management Systems (BMS) to achieve full battery capacity and better balancing.
  • Dynamic Equalization Current: The balancer does not continuously equalize at its maximum current (5.5A). The equalization current is proportional to the voltage difference between the batteries; higher differences result in higher currents.
  • Quality Investment: Investing in a quality active balancer like this can significantly improve battery pack performance and longevity compared to cheaper, less effective alternatives.
  • Custom Control: For advanced users, the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.