STEPPERONLINE DM556Y

Contents

STEPPERONLINE Digital Stepper Motor Driver DM556Y User Manual

Model: DM556Y | Brand: STEPPERONLINE

1. Introduction & Features

The Y series Open-loop drivers are digital stepper drivers designed for simple setup and operation. They utilize advanced stepper control technology to smoothly power 2-phase and 4-phase stepper motors, providing optimal torque, low motor heating, and reduced noise. Micro-step and output current settings are configured via DIP switches. These drivers are suitable for applications requiring basic step & direction control for NEMA 8, 11, 14, 16, 17, 23, 24, and 34 stepper motors.

Key Features:

  • Anti-Resonance for optimal torque, extra smooth motion, low motor heating and noise.
  • Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
  • Step & direction (PUL/DIR) control.
  • Multi-Stepping for smooth motor movement.
  • TTL compatible and optically isolated inputs.
  • Input voltage DC18~36V, DC20~50V, DC36~110V (AC18~80V).
  • Micro-step resolutions: 200~6400, 200~40000, 400~40000.
  • Output current settings: 0.3~2.2A, 1~4.2A, 1.7~5.6A, 2.4~7.2A.
  • Soft-start with no "jump" when powered on.
  • Automatic idle-current reduction.
  • Protections for over-voltage and over-current.

For a comprehensive guide, please refer to the official user manual PDF: DM556Y User Manual (PDF).

2. Specifications

2.1 Operating Environment and Other Specifications (Tj=25°C/77°F)

Category Parameter Value
Cooling Method Natural Cooling or Forced Cooling
Environment Avoid dust, oil fog and corrosive gases
Operating Environment Ambient Temperature 0°C ~ 65°C (32°F ~ 149°F)
Humidity 40%RH ~ 90%RH
Operating Temperature 0°C ~ 50°C (32°F ~ 122°F)
Vibration 10-50Hz / 0.15mm
Storage Temperature -20°C ~ 65°C (-4°F ~ 149°F)
Weight (DM556Y) 300g

2.2 Electrical Specifications (DM556Y)

Parameter Min Typical Max Unit
Output Peak Current 1.7 (1.2 RMS) - 5.6 (4.0 RMS) A
Supply Voltage 20 36 50 VDC
Logic Signal Current 7 10 15 mA
Pulse input frequency 0 - 200 kHz
Minimal pulse width 2.5 - - µS
Minimal direction setup 2.5 - - µS
Isolation resistance 500 - - MΩ

2.3 Mechanical Specifications (DM556Y)

DM556Y Mechanical Dimensions Diagram

Description: This diagram illustrates the mechanical dimensions of the DM556Y stepper motor driver in millimeters. Key dimensions include a length of 118mm, width of 76mm, and height of 33mm. It also shows mounting hole positions and heatsink details. Side mounting is recommended for better heat dissipation.

3. Setup & Wiring

3.1 Pin Assignment and Description (Connector P1)

Pin Function Details
PU+ Connected to the signal power supply, +5~+24V can be driven. Higher than 24V needs a current limiting resistor in PU-.
PU- The falling edge is valid and the pulse goes one step when the pulse goes from high to low. Requirements: Low level: 0~0.5V, high level 5~24V, pulse width greater than 2.5 microseconds.
DR+ Connected to the signal power supply, +5~+24V can be driven. Higher than 24V needs a current limiting resistor in DR-.
DR- Used to change the direction of the motor. Requirements: Low level: 0~0.5V, high level 5~24V, pulse width greater than 2.5 microseconds.
MF+ Connected to the signal power supply, +5~+24V can be driven. Higher than 24V needs a current limiting resistor in MF-.
MF- When active (low level), the motor coil current is turned off, the driver stops working, and the motor is in a free state.

3.2 Control Signal Connector (P1) Interface Wiring

The Y series open-loop drivers accept differential and single-ended inputs (including open-collector and PNP output). These inputs are optically isolated to minimize electrical noise. Line drive control signals are recommended for increased noise immunity.

Resistor values for +5V, +12V, +24V signal power supply:

  • +5V: R1=0, R2=0
  • +12V: R1=510Ω, R2=820Ω
  • +24V: R1=1.2KΩ, R2=1.8KΩ
Differential Wiring Method Diagram

Figure 1: Differential Wiring Method. This diagram shows how to connect a controller to the driver using differential signals for improved noise immunity.

Independent Common Anode Wiring Method Diagram

Figure 2: Independent Common Anode Wiring Method. This diagram illustrates connections for independent common anode signals.

Common Anode Wiring Method Diagram

Figure 3: Common Anode Wiring Method. This diagram shows connections for common anode signals.

Independent Common Cathode Wiring Method Diagram

Figure 4: Independent Common Cathode Wiring Method. This diagram illustrates connections for independent common cathode signals.

3.3 Motor Connections

The DM556Y driver supports 4-lead, 6-lead, and 8-lead stepper motors. Ensure correct wiring based on your motor type for optimal performance.

3.3.1 Connections of 4-lead Motor

DM556Y Stepper Motor Driver with 4-lead Motor Connections

Description: This image shows the DM556Y driver with its motor connection terminals (A+, A-, B+, B-). For a 4-lead stepper motor, connect the motor's A+ to the driver's A+, A- to A-, B+ to B+, and B- to B- terminals. NC terminals are not used.

3.3.2 Connections of 6-lead Motor

For 6-lead stepper motors, there are typically two wiring configurations:

  • Half Coil (Higher Speed): This configuration uses half of the motor's winding, resulting in higher speed but lower torque. The center taps of the windings are usually left unconnected.
  • Full Coil (Higher Torque): This configuration uses the full winding, providing higher torque but potentially lower top speed. The center taps are typically connected to the power supply or left floating depending on the motor and driver.

Refer to your motor's specific datasheet for the correct wiring diagram for half coil and full coil configurations with a 6-lead motor.

3.3.3 Connections of 8-lead Motor

8-lead stepper motors offer the most flexibility and can be wired in series or parallel:

  • Series Connections: Wiring the coils in series provides higher inductance, resulting in higher torque at lower speeds.
  • Parallel Connections: Wiring the coils in parallel provides lower inductance, allowing for higher speeds but potentially lower torque at very low speeds.

Consult your 8-lead motor's datasheet for detailed wiring instructions for series and parallel configurations to the DM556Y driver.

4. Operating

The DM556Y driver operates by receiving step and direction signals from a controller. The output current and micro-step resolution are configured using the DIP switches on the unit. Refer to the tables on the device label or in the full PDF manual for specific DIP switch settings for current and micro-stepping.

Ensure the power supply voltage is within the specified range (20-50VDC) and that the motor is correctly wired according to its lead configuration (4-lead, 6-lead, or 8-lead).

DM556Y Stepper Motor Driver with DIP Switch Settings

Description: This image shows the DM556Y driver with its DIP switches visible, used for setting current and micro-step resolution. The tables printed on the driver indicate the switch positions for various settings.

5. Maintenance

The DM556Y stepper motor driver is designed for reliable operation with minimal maintenance. To ensure longevity and optimal performance:

  • Environment: Operate the driver in an environment free from dust, oil fog, and corrosive gases.
  • Cooling: Ensure adequate cooling. Side mounting is recommended for better heat dissipation. If operating in high ambient temperatures or with high current settings, forced cooling (e.g., a fan) may be necessary.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
  • Cleaning: Keep the exterior of the driver clean and free from debris that could obstruct airflow or cause overheating.

No user-serviceable parts are inside the unit. Do not attempt to open or repair the driver yourself, as this will void the warranty.

6. Troubleshooting

This section provides solutions to common issues encountered with the DM556Y stepper motor driver.

Symptoms Possible Problems
Motor is not rotating
  • No power
  • Fault condition exists
  • The driver is disabled
Motor rotates in the wrong direction
  • The direction signal level is reverse
Erratic motor motion
  • Control signal is too weak
  • Control signal is interfered
  • Wrong motor connection
  • Something wrong with motor coil
  • Current setting is too small
Motor stalls during acceleration
  • Motor is undersized for the application
  • Acceleration is set too high
  • Power supply voltage too low
Excessive motor and driver heating
  • Inadequate heat sinking/cooling
  • Motor current setting is too high

7. User Tips

  • These drivers are noted for being well-made, quiet, and effective, especially when integrated into systems like those using an EC500 controller.
  • Ensure all connections are firm and correctly matched to avoid erratic motion or non-operation.
  • Proper heat dissipation is crucial for longevity; consider side mounting and, if necessary, additional forced cooling.

8. Warranty & Support

8.1 Warranty

STEPPERONLINE® warrants its products against defects in materials and workmanship for a period of 12 months from shipment. During the warranty period, STEPPERONLINE will, at its option, repair or replace products proven to be defective. To obtain warranty service, a Returned Material Authorization (RMA) number must be acquired before returning the product.

Exclusions: The warranty does not cover products damaged due to improper or inadequate handling by the customer, incorrect wiring, unauthorized modification or misuse, or operation outside the product's electrical or environmental specifications.

For more detailed descriptions, please refer to the specifications on the official website: www.omc-stepperonline.com.

8.2 Support

For technical assistance or inquiries, please contact OMC Corporation Limited:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.