TLZWLA CB-1212-112D

Contents

TLZWLA CB-1212-112D Flashlight Button Switch User Manual

1. Safety Information

Please read and understand all safety instructions before installing or operating the TLZWLA CB-1212-112D button switch.

  • Operation should be performed by individuals with appropriate electrical knowledge.
  • Always disconnect power from the circuit completely before installing, maintaining, or troubleshooting the switch.
  • Avoid installing or operating the switch in damp or wet environments to prevent electrical hazards.

2. Product Overview

The TLZWLA CB-1212-112D is an ultra-thin, 2-pin latching push-button switch designed for various electronic applications, including flashlights and DIY projects. It features a compact design and a reliable latching mechanism, meaning one press turns it ON, and the next press turns it OFF.

Front and side view of two TLZWLA CB-1212-112D button switches
Figure 2.1: Front and side view of two TLZWLA CB-1212-112D button switches.

3. Specifications

AttributeValue
Brand NameTLZWLA
Model NumberCB-1212-112D (Ultra-thin switch)
Item TypeSWITCHES
Switch TypePush Button Switch
FeaturesLatching switch
MaterialCopper
Current Rating1A
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
CertificationRoHS, CE
High-concerned chemicalNone
Dimensions (L x W x H)12mm x 12mm x 9.4mm (0.47in x 0.47in x 0.35in)
Dimensional drawing of the TLZWLA CB-1212-112D button switch with measurements
Figure 3.1: Dimensional drawing of the button switch.

4. Installation

Follow these steps for proper installation of the button switch:

  1. Disconnect Power: Ensure all power to the circuit is completely disconnected before beginning installation.
  2. Identify Terminals: The switch has two pins for electrical connection. These pins are typically used for series connection within a circuit.
  3. Wire Connection: Solder or securely connect the circuit wires to the switch's pins. Ensure connections are firm, insulated, and free from short circuits.
  4. Mounting: Integrate the switch into your device or project enclosure. Its compact size (12x12x9.4mm) allows for integration into tight spaces.
  5. Reconnect Power: Once the switch is securely installed and all connections are verified, reconnect power to the circuit.

5. Operation

The TLZWLA CB-1212-112D is a latching push-button switch. Its operation is as follows:

  • To turn ON: Press the button once. The switch will 'latch' and remain in the ON (closed circuit) state.
  • To turn OFF: Press the button again. The switch will 'unlatch' and return to the OFF (open circuit) state.

The switch provides a tactile and audible click to confirm its state change.

6. Maintenance

To ensure the longevity and reliable performance of your switch, consider the following maintenance tips:

  • Cleaning: Keep the switch free from dust, dirt, and moisture. Use a dry, soft cloth for cleaning. Avoid using liquid cleaners directly on the switch.
  • Inspection: Periodically check the switch and its connections for any signs of wear, damage, or loose wiring.
  • Handling: Avoid applying excessive force to the button or terminals. Do not use metallic objects to manipulate the switch, as this can cause damage or short circuits.

7. Troubleshooting

If you encounter issues with your button switch, refer to the following troubleshooting steps:

  • Switch Not Responding:
    • Verify that power is supplied to the circuit where the switch is installed.
    • Check all wiring connections for looseness, corrosion, or improper soldering.
    • Ensure the switch is correctly installed and not physically obstructed.
  • Testing Switch Continuity:
    • Disconnect Power: Always disconnect power from the circuit before testing the switch.
    • Use a Multimeter: Set your multimeter to continuity mode or resistance (Ohms).
    • Test ON State: Press the switch to the ON (latched) position. Place the multimeter probes on the two pins of the switch. The multimeter should show a very low resistance (close to 0 Ohms) or indicate continuity.
    • Test OFF State: Press the switch to the OFF (unlatched) position. Place the multimeter probes on the two pins. The multimeter should show infinite resistance (open circuit) or no continuity.

    If the switch does not show the expected continuity readings, it may be faulty and require replacement.

8. User Tips

Based on user experiences, here are some helpful tips for using your TLZWLA button switches:

  • Breadboard Friendly: These switches are suitable for prototyping on breadboards due to their standard pin spacing and compact size.
  • Flashlight Repairs: Many users have found these switches to be excellent replacements for faulty switches in various flashlights.
  • Compact Projects: Their ultra-thin and compact design makes them ideal for projects with limited space where a small footprint is crucial.
  • Tactile Feedback: The switches offer a firm and audible click, providing clear feedback on their state change, which is useful in applications where visual confirmation might be difficult.

9. Frequently Asked Questions (FAQ)

Q: Is this a momentary or latching switch?
A: This is a latching switch. Press it once to turn it ON, and press it again to turn it OFF.
Q: How can I tell if the switch is working correctly?
A: You can test its continuity using a multimeter. In the ON position, it should show continuity (low resistance), and in the OFF position, it should show no continuity (infinite resistance). Always ensure power is disconnected from the circuit before performing any tests.
Q: What voltage range is suitable for this switch?
A: The switch is designed for low voltage applications, specifically below 50Vac or 75Vdc.

10. Warranty and Support

This product comes with a ten-year warranty from the date of purchase. For support or warranty claims, please contact the seller or manufacturer with your purchase details and proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.