KeKeQeen ANL FUSE HOLDER

Contents

ANL Fuse Holder Instruction Manual

Brand: KeKeQeen | Model: ANL FUSE HOLDER

1. Product Overview

The ANL Fuse Holder is designed to provide overcurrent protection for automotive audio systems and other high-current applications. It accommodates ANL fuses ranging from 30A to 500A, ensuring the safety of your electrical circuits.

ANL Fuse Holder

Figure 1: ANL Fuse Holder with clear protective cover.

Video 1: Product overview of the ANL Fuse Holder.

2. Setup and Installation

Proper installation is crucial for the safe and effective operation of your ANL Fuse Holder.

2.1 Mechanical Dimensions

Refer to the diagram below for precise measurements to ensure proper fitment and mounting.

ANL Fuse Holder Mechanical Dimensions

Figure 2: Mechanical dimensions of the ANL Fuse Holder. (Note: Diagram includes blowing time characteristics and part numbers table)

  • Overall Length: 80.8 mm (3.17 inches)
  • Width: 19.2 mm (0.76 inches)
  • Height: 27.8 mm (1.09 inches)
  • Fuse Slot Length: 61.6 mm (2.43 inches)
  • Terminal Width: 22.1 mm (0.87 inches)
  • Thickness: 8.3 mm (0.33 inches)
  • Bolt Spacing (center-to-center): 35.3 mm (1.39 inches)
  • Mount Hole Diameter: 8mm (0.31 inches)
  • Two Mounting Hole Distance: 11.3 cm (4.45 inches)
  • Thread Diameter: 7.8mm (0.30 inches)

2.2 Installation Steps

  1. Select Mounting Location: Choose a dry, secure location close to the power source (e.g., battery) that is protected from physical damage and excessive heat.
  2. Mount the Holder: Securely fasten the ANL Fuse Holder using appropriate screws through its mounting holes.
  3. Prepare Cables: The fuse holder accepts 0, 4, or 8 GA input and output cables. Ensure you use appropriately sized ring terminals (not included) for a secure connection. Strip the cable insulation to the correct length for the terminals.
  4. Connect Cables: Loosen the bolts on the fuse holder terminals. Insert the prepared cable ends with ring terminals onto the bolts. Tighten the bolts firmly to ensure a good electrical connection.
  5. Insert Fuse: Select an ANL fuse with the correct amperage rating for your circuit. Place the fuse between the two terminals, ensuring it sits flat and makes good contact.
  6. Install Cover: Place the clear protective non-conductive, heat-resistant cover over the fuse holder. This protects the fuse and terminals from environmental elements and accidental contact.
ANL Fuse Holder with Fuse

Figure 3: ANL Fuse Holder with an ANL fuse installed.

3. Operating Principles

The ANL Fuse Holder functions as a safety device by housing a fuse that protects your electrical system from overcurrent conditions. When the current flowing through the circuit exceeds the fuse's rated amperage for a specified duration, the metallic element within the fuse melts (blows), breaking the circuit and preventing damage to connected components.

3.1 Electrical Characteristics (Blowing Time)

The time it takes for a fuse to blow depends on the overload percentage:

% of Rated CurrentOpening Time (Min)Opening Time (Max)
100%4 hr.-
250%-300s

4. Maintenance

  • Regular Inspection: Periodically inspect the fuse holder and fuse for any signs of corrosion, discoloration, physical damage, or loose connections. Ensure the protective cover is securely in place.
  • Fuse Replacement: If a fuse blows, it must be replaced with a new ANL fuse of the exact same amperage rating. Never use a fuse with a higher rating, as this can lead to severe damage or fire.
  • Cleaning: If necessary, disconnect power and gently clean the fuse holder terminals with a non-abrasive cleaner to remove any dirt or corrosion.

5. Troubleshooting

  • No Power to Device: If the connected device is not receiving power, first check the ANL fuse. If the metallic element inside the fuse is broken or discolored, the fuse has blown. Replace it with a new fuse of the correct rating.
  • Fuse Blows Repeatedly: If a new fuse blows immediately or shortly after installation, this indicates a persistent overcurrent condition, a short circuit, or an overloaded circuit. Do not continue replacing fuses without investigating the underlying cause. Consult a qualified technician to diagnose and repair the electrical system.
  • Loose Connections: Ensure all cable connections to the fuse holder terminals are tight and secure. Loose connections can cause resistance, heat buildup, and intermittent power.

6. Specifications

6.1 General Specifications

  • Brand Name: KeKeQeen
  • Model Number: ANL FUSE HOLDER
  • Use: Automotive
  • Safety Standards: IEC
  • Certification: CE, RoHS
  • EU LVD Voltage: Below 50Vac or 75Vdc

6.2 Electrical Specifications

  • Voltage Rating: 32VDC; 125VAC
  • Breaking Capacity: High
  • Interrupting Rating:
    • 2000A @ 32VDC (40A~400A)
    • 1500A @ 32VDC (500A~600A)
    • 2500A @ 32VDC (700A~800A)

6.3 Material Specifications

  • Body Material: Bakelite, Plastic (Case)
  • Terminal Material: Copper, Brass (Gold Plated for 40A~80A), Copper Alloy (Gold Plated)

6.4 Package Dimensions

  • Length: 15 cm
  • Width: 8 cm
  • Height: 5 cm
  • Weight: 0.13 kg

6.5 Part Numbers and Amperage

Part NumberAmperageDim "F" (mm)
ANL-40A40A8.8±0.2
ANL-50A50A8.8±0.2
ANL-60A60A8.8±0.2
ANL-80A80A8.8±0.2
ANL-100A100A8.8±0.2
ANL-125A125A8.8±0.2
ANL-130A130A8.8±0.2
ANL-150A150A8.8±0.2
ANL-175A175A8.8±0.2
ANL-180A180A8.8±0.2
ANL-200A200A8.8±0.2
ANL-225A225A8.8±0.2
ANL-250A250A8.8±0.2
ANL-275A275A8.8±0.2
ANL-300A300A8.8±0.2
ANL-400A400A8.8±0.2
ANL-425A425A8.8±0.2
ANL-500A500A8.8±0.2
ANL-600A600A11.11±0.3
ANL-700A700A11.11±0.3
ANL-800A800A11.11±0.3

7. User Tips

  • Cable Compatibility: The fuse holder is designed for 0, 4, or 8 GA cables. Ensure your cables and ring terminals match these specifications for optimal performance and safety.
  • Correct Amperage: Always use an ANL fuse with the amperage rating appropriate for the circuit it is protecting. Using an incorrect rating can compromise safety or cause nuisance blowing.
  • Secure Connections: Loose connections are a common cause of electrical issues. Double-check that all bolts are tightened firmly to ensure good electrical contact and prevent heat buildup.
  • Quality Product: Users have noted the good quality and reliability of this fuse holder. Proper installation will ensure it performs as expected.

8. Warranty and Support

For any warranty claims, technical support, or inquiries regarding your ANL Fuse Holder, please contact the seller directly. Keep your purchase records handy for faster service.

A detailed specification sheet for this product is available in PDF format: View User Manual (PDF)

© 2024 KeKeQeen. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.