diymore Boost Buck Converter Module

Contents

DC-DC Boost Buck Converter Module User Manual

Model: Boost Buck Converter Module

1. Introduction

This manual provides instructions for the diymore DC-DC Automatic Adjustable Step Up Down Boost Buck Converter Power Module. This non-isolated synchronous rectification module is designed to automatically adjust its output voltage to be higher or lower than the input voltage, providing a stable and adjustable power source for various electronic applications.

2. Safety Precautions

  • Always ensure correct polarity when connecting input and output. Incorrect connections can damage the module and connected devices.
  • This module does NOT have input reverse polarity protection. If required, an external diode must be installed at the input port.
  • Do not exceed the maximum input voltage, output current, or output power specifications.
  • Ensure adequate ventilation, especially when operating at higher currents or power levels, to prevent overheating.
  • Avoid short-circuiting the output, as this can damage the module.
  • Handle the module with care to avoid electrostatic discharge (ESD) damage.

3. Setup and Connections

The module features screw terminals for easy connection. Refer to the diagram below for terminal identification.

Top view of the converter module with input/output terminals, CV/CC potentiometers, and soft switch interface labeled.
Figure 1: Module Layout and Connections
  • Input Terminals:
    • IN+: Positive input voltage (DC 5V-30V)
    • IN-: Negative input voltage
  • Output Terminals:
    • OUT+: Positive output voltage (DC 1.25V-30V)
    • OUT-: Negative output voltage
  • Soft Switch External Interface (KEY): This interface can be used for external control of the module's operation.

Ensure all connections are secure before applying power.

4. Operating Instructions

The module has two potentiometers for adjusting the output voltage (CV) and output current (CC).

Close-up top view of the converter module with input/output terminals, CV/CC potentiometers, and soft switch interface labeled.
Figure 2: Adjustment Potentiometers

4.1. Output Voltage Adjustment (CV Constant Voltage Adjust)

  1. Connect the input power supply to the IN+ and IN- terminals.
  2. Using a voltmeter, measure the voltage across the OUT+ and OUT- terminals.
  3. Adjust the CV potentiometer (Constant Voltage Adjust) clockwise or counter-clockwise until the desired output voltage is achieved.

4.2. Output Current Adjustment (CC Constant Current Adjust)

This adjustment is crucial for applications like LED driving or battery charging.

  1. First, adjust the output voltage using the CV potentiometer to the value required by your load (e.g., battery charging voltage or LED forward voltage).
  2. Turn the CC potentiometer (Constant Current Adjust) counter-clockwise approximately 30 turns until the output current is at its minimum.
  3. Connect your load (e.g., an LED or a fully discharged battery) to the output terminals.
  4. Adjust the CC potentiometer clockwise until the desired output current is reached.
  5. Important Note for Battery Charging: For accurate current setting when charging a battery, the battery must be fully discharged first. If the battery has remaining power, the charge current will be smaller, leading to inaccurate settings. Do not use a short-circuit method to adjust current, as the boost converter's circuit structure does not allow for this.

5. Maintenance

  • Keep the module clean and free from dust and debris.
  • Avoid exposure to moisture or corrosive environments.
  • Ensure proper airflow around the module, especially around the heat sinks, to maintain optimal operating temperatures.
  • Periodically check terminal connections for tightness.

6. Troubleshooting

  • No Output Voltage: Check input power supply, ensure connections are correct and secure. Verify input voltage is within the 5V-30V range.
  • Incorrect Output Voltage/Current: Re-adjust CV and CC potentiometers as per operating instructions. Ensure your measurement tools are accurate.
  • Module Overheating: This can occur if the output current or power exceeds the module's limits, especially without sufficient cooling. Reduce the load or ensure better ventilation. The module has overtemperature protection which automatically reduces output voltage.
  • Output Current Lower Than Expected: Check if the load is drawing the expected current. Ensure the CC potentiometer is correctly adjusted. Note that natural cooling limits long-term output current to 5A, with a maximum of 10A peak (6A for long-term work). Long-term power is 50W, with a maximum of 100W.
  • Physical Damage: If the module appears physically damaged (e.g., dented capacitors), it may operate poorly or not at all. Inspect the module upon receipt.

7. Specifications

FeatureSpecification
Module PropertiesNon-isolated synchronous rectification automatic boost/buck converter
Input VoltageDC 5V-30V
Input Current8A (MAX), Peak 10A (6A for long-term work)
Static Current4mA (approximate, varies with operating voltage)
Output Voltage1.25V-30V (continuously adjustable)
Output Current10A (MAX), 5A (natural cooling long-term)
Output Constant Current Range0.2A-10A
Output Power50W (long-term), 100W (MAX)
Working Temperature-40°C to 85°C
Operating Frequency150KHz
Conversion EfficiencyTypically 91% (12V to 12V 5A), MAX 93%
Overcurrent ProtectionYes
Short Circuit ProtectionYes (current-limiting protection)
Overtemperature ProtectionYes (automatically reduces output voltage)
Input Reverse Polarity ProtectionNone (install diode at input port if needed)
Output Prevent BackflowYes (no diode needed for charging)
Connection MethodTerminals (IN is input, OUT is output)
Dimensions (L*W*H)60mm * 53mm * 22mm
Brand Namediymore
Model NumberBoost Buck Converter Module
Current TypeDC
PhaseSingle-phase
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
Diagram showing the dimensions of the converter module: 60mm (length), 53mm (width), 22mm (height).
Figure 3: Module Dimensions

8. User Tips

  • This module is highly versatile; it can both step up and step down voltage, for example, converting 12V to 5V or 12V to 24V.
  • It is effective for charging batteries, with both current and maximum voltage settings working reliably.
  • When setting the current for battery charging, ensure the battery is fully discharged for the most accurate adjustment.
  • The module is customizable and adjustable, making it suitable for various power supply needs.

9. Frequently Asked Questions (FAQ)

Q: Can this module both increase and decrease voltage?
A: Yes, it is an automatic boost/buck converter, meaning it can output a voltage higher or lower than its input voltage.
Q: Does it have reverse polarity protection for the input?
A: No, it does not have built-in input reverse polarity protection. An external diode should be installed at the input port if this protection is required.
Q: Can I use this module to charge batteries?
A: Yes, it can be used to charge batteries. For accurate current setting, ensure the battery is fully discharged before adjusting the CC potentiometer.

10. Warranty and Support

For specific warranty terms, technical support, or service inquiries, please refer to the seller or manufacturer directly. Keep your purchase records for any warranty claims.

© 2023 diymore. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.