YIHUA 853D 5A II

Contents

YIHUA 853D 5A II 3-in-1 Soldering Station, Hot Air Rework Station, and DC Power Supply User Manual

Model: 853D 5A II

1. Introduction

Thank you for purchasing the YIHUA 853D 5A II 3-in-1 Multi Station. This unit combines a soldering station, a hot air rework station, and a DC power supply into one compact device. It is designed for versatility and precision in various electronic repair and manufacturing tasks.

The company reserves the right to improve and upgrade products. Product specifications and design are subject to change without notice.

1.1. Applications

  • Suitable for desoldering and soldering operations on a broad range of components, including SOIC, CHIP, QFP, PLCC, BGA, and SMD. It is especially suited for desoldering operations on in-line sockets.
  • Can be used for heat shrinking, drying, paint removal, glue removal, defrosting, pre-heating, and glue soldering.
  • Ideal for technology product development, education, electronics manufacturing lines, and mobile phone/communication equipment repair.

1.2. Key Features

  • Equipped with soldering iron, hot air gun, DC power supply, and a 5V 2A USB interface for charging during repair.
  • PID program-controlled temperature control technology ensures stable working temperature.
  • Lightweight design for easy transportation.
  • User-friendly functions: Digital temperature correction, Celsius/Fahrenheit display conversion, soldering iron 0-99 minutes sleep function, hot air fan malfunction protection, and power supply over-temperature protection.

2. Setup

2.1. Unpacking and Inspection

Carefully unpack all components and inspect for any damage. Ensure all items listed in the 'What's in the Box' section are present.

2.2. What's in the Box

SET1: Basic 853D5A-II

  • Soldering station with soldering iron & hot air gun
  • Laptop conversion heads and cables * 1 set
  • Suction tin gun * 1pc (XQ-1 or XQ-5, shipped randomly)
  • Advanced Anti static Tweezer No.15 * 1pc
  • Anti-static wristband * 1pc
  • Soldering wire (50g, 0.5mm) * 1 pc
  • Soldering iron holder * 1 pc
  • Air gun nozzles *4pcs
  • Crocodile clip *1pc

SET2: Updated SJ-853D5A-II

  • Soldering station with soldering iron & hot air gun
  • Soldering iron holder * 1 pc
  • Air gun nozzles *5pcs
  • Crocodile clip *1pc
  • Air gun nozzle holder * 1pc

Kindly reminder: Only the upgraded 853D5A-II comes with the new updated nozzle stand.

YIHUA 853D 5A II 3-in-1 Soldering Station with all accessories
Figure 1: YIHUA 853D 5A II 3-in-1 Soldering Station with included accessories.

2.3. Component Installation

  1. Hot Air Gun Holder: Install the hot air gun holder onto the left side of the station.
  2. Hot Air Nozzles: Install the required nozzle onto the hot air gun. Larger diameter nozzles are recommended. Ensure installation is done only when the steel pipe and nozzle have cooled. Do not use brute force or pull the nozzle edge with tweezers.
  3. Soldering Iron: Connect the soldering iron to the station and place it into its holder.
New Upgraded Nozzles Easy Plug-pull
Figure 2: New upgraded nozzles with easy plug-pull mechanism.
Soldering Iron Components
Figure 3: Soldering iron components: comfortable heat-resistant silicone sleeve, heating element, SGS certified soldering tip, stainless steel cooling cylinder, and hot-proof high-temperature resistant bakelite thread head.

2.4. Power Connection

Connect the station's power cord to an appropriate electrical outlet (110V or 220V-240V depending on model).

3. Operating Instructions

Video 1: Demonstration of the YIHUA 853D 5A II in operation, showing hot air gun and soldering iron usage.

3.1. Control Panel Overview

LCD Display Screen
Figure 4: LCD Display Screen showing CH1 (Hot Air), CH2 (Soldering Station) temperatures, and DC Power Supply Output Voltage and Current.

The control panel features an LCD display screen to monitor all settings and specifications. It includes dedicated controls for the hot air gun, soldering station, and DC power supply.

Control Panel Layout
Figure 5: Detailed view of the control panel and connections.

Control Panel Components:

  1. Temperature Increase and Decrease Buttons (Hot Air Rework Station)
  2. Temperature Display (Hot Air Rework Station)
  3. Power Switch (Hot Air Rework Station)
  4. Power Switch (Soldering Station)
  5. Temperature Display (Soldering Station)
  6. Fahrenheit/Celsius Unit Display Selector
  7. Hot Air Gun Handle Cord (853D 5A integrated gun, 853D+5A detachable gun)
  8. Air Volume Adjustment Knob
  9. Receptacle (Soldering Iron)
  10. Output Voltage Terminal (+ Positive)
  11. Output Voltage/Voltmeter Terminal (- Negative)
  12. Voltmeter Terminal (+ Positive)
  13. Output/Voltmeter Mode Switch
  14. Fine Adjustment Knob (Current)
  15. Fine Adjustment Knob (Voltage)
  16. Coarse Adjustment Knob (Voltage)
  17. Coarse Adjustment Knob (Current)
  18. A/mA Unit Display Selector
  19. Current Display
  20. Power Switch (DC Power Supply)
  21. Voltage Display
  22. Temperature Increase and Decrease Buttons (Soldering Station)

3.2. Hot Air Rework Station Operation

  1. Turn ON the master power switch located at the rear of the station.
  2. Turn ON the hot air rework station's power switch. The temperature display will show "---" indicating standby mode.
  3. Press the increase (▲) or decrease (▼) button to set the desired temperature.
  4. Pick up the hot air gun from its holder to enter standard operation mode. The operation indicator light (dot at bottom-right of display) will turn ON.
  5. Adjust the air volume using the adjustment knob.
  6. When operation is complete, place the hot air gun back in its holder. The hot air gun will enter cooling mode.
  7. Turn OFF the hot air power switch. The operation indicator will turn OFF. The temperature display will turn OFF when the gun cools below 100°C/212°F.

CAUTION: When the hot air automatic/manual mode is set to manual, the hot air gun will begin heating immediately when turned ON.

Cool/Hot Air One-Button Conversion
Figure 6: One-button conversion between cool and hot air modes.

3.3. Soldering Station Operation

  1. Turn ON the master power switch located at the rear of the station.
  2. Turn ON the soldering station's power switch. The heating element will begin heating, and its operation indicator light (dot at bottom-right of display) will turn ON.
  3. The indicator light will stay ON while heating, then blink rapidly when the temperature stabilizes. Begin operation once the temperature is stable.

CAUTION: For the first use of the soldering iron tip, set the temperature to 250°C/482°F. When the iron is just hot enough to melt solder, coat the tip with a layer of solder (rosin core solder is recommended), then set the temperature to your desired value.

Soldering Station Sleep Mode
Figure 7: Soldering station sleep mode extends heating element lifespan and saves energy. Sleep time can be set from 0-99 minutes.

3.4. DC Power Supply Operation

  1. Connect the station's power cord to an electrical outlet.
  2. Turn ON the DC power supply's power switch. The C.V. indicator will turn ON (when current coarse and fine adjustment knobs are not at 0). The current and voltage displays will show "000" for current and the output voltage value.
  3. Adjust the voltage coarse and fine adjustment knobs to set the desired output voltage.
  4. For Constant Current (C.C.) Mode:
    1. First, adjust the voltage coarse or fine adjustment knob to any value between 2V to 5V.
    2. Then, adjust the current coarse or fine adjustment knob to 0 (turn all the way anticlockwise).
    3. Use test leads to connect the positive terminal (+) to the negative terminal (-).
    4. Finally, adjust the current coarse or fine adjustment knob clockwise to the desired current for operation.
  5. Connect the load to the positive (+) and negative (-) terminal, and the power supply will begin powering the load.
30V 5A Switch DC Power Supply with Protections
Figure 8: The 30V 5A DC Power Supply features overload, over current, over voltage, overheating, and shortcircuit protection.

3.5. Advanced Settings

3.5.1. Digital Temperature Calibration

Temperature discrepancies may occur due to environmental changes or replacement of components. This function allows correction of these discrepancies to improve work efficiency and prolong soldering iron lifespan.

  1. When the hot air rework station's (or soldering station's) temperature is stabilized, press and hold both the temperature increase and decrease buttons for approximately 2 seconds. The display will blink with 3 digit dots while showing the set temperature.
  2. Press the temperature decrease or increase button to enter the measured temperature value.
  3. Press and hold both temperature increase and decrease buttons to confirm entry and exit the calibration interface.

3.5.2. °F/°C Temperature Display Conversion

Flip the °F/°C toggle switch on the control panel to select either Fahrenheit or Celsius display mode.

Celsius/Fahrenheit Temperature Modes
Figure 9: Choose between Celsius (°C) and Fahrenheit (°F) temperature display modes.

3.5.3. Hot Air Gun Automatic / Manual Mode

  1. Turn ON the hot air rework station ONLY.
  2. Press and hold both the hot air rework station's temperature INCREASE and the soldering station temperature DECREASE buttons for approximately 2 seconds. The display will show "A1" for automatic mode ("A0" for manual mode).
  3. Press the hot air rework station's temperature increase button to select automatic mode, or decrease button for manual mode.
  4. Stop operating for approximately 3 seconds to exit the setting interface.

3.5.4. Energy-Saving Tip

When a specific function (soldering station, hot air rework station, or DC power supply) is not in use, turn OFF its respective power switch. If all functions are turned OFF, the display will blink with "---". In this state, turn OFF the master power switch and disconnect the station's power cord from the electrical outlet to save energy.

One Key Handles All Settings
Figure 10: Long press to enter function settings for temperature display mode, buzzer, hot air gun auto/manual mode, soldering station sleep mode, and power supply output holding.

4. Maintenance & Precautions

4.1. Hot Air Rework Station

  • Keep the air outlet clear and free of blockages at all times.
  • Install nozzles only when the steel pipe and nozzle have cooled. Install correctly; do not use brute force, pull the nozzle edge with tweezers, or over-tighten screws.
  • Select the appropriate nozzle based on operation requirements. When using smaller nozzles than standard, use maximum air volume with a relatively lower temperature setting for the shortest possible duration to avoid damage.
  • Maintain a minimum distance of 2mm between the object and the hot air gun's air outlet.
  • Avoid direct contact with facial parts due to burn risk. White fumes may emit during first use but will dissipate shortly.
  • Hot Air Zero-Air Protection: If the hot air gun stops emitting air abnormally during operation, the system will cut power to the heating element to prevent damage from accumulated heat and improve safety.

4.2. Soldering Station

  • If the soldering iron tip oxidizes, causing low temperature or poor tinning, do not increase temperature. Instead, clean the tip using a metal wool ball:
    1. Set temperature to 300°C (572°F).
    2. Once stable, gently rub the tip inside the metal wool ball.
    3. When partially removed, apply solder onto the tip while rubbing until solder adheres completely. If severely oxidized, replace the tip.
  • DO NOT use metal files to remove oxidization from the soldering iron tip. Replace deformed or rusted tips.
  • DO NOT apply excessive force when soldering; it can damage the tip and not improve heat transfer.
  • When placing the soldering iron back in its holder after high-temperature operation, adjust the temperature to 250°C (482°F) or below for idling. High idle temperatures accelerate heating element aging and shorten its lifespan.
  • After every operation, always clean the soldering iron tip and coat it with a layer of solder to prevent oxidization.

4.3. DC Power Supply

  • The built-in cooling fan will operate when the machine's internal temperature reaches 45°C/113°F to cool the station down.

5. Troubleshooting Guide

  • Display shows "S-E": This indicates a fault in the soldering iron or hot air gun's sensor module. Replace the heating element (which includes the sensor module). Alternatively, check if the handle is properly connected (turn off the station, connect the handle, then turn on).
  • Display shows "F-1" or "F-2": This indicates the station is in "zero-air protection" mode. Check the hot air gun's motor and its power circuitry.
  • Replacing Heating Element: When replacing the heating element, ensure the original connecting order and colors of the wires are maintained and connected correctly.

6. Specifications

YIHUA 853D 5A II Specifications Table
Figure 11: Detailed specifications for the YIHUA 853D 5A II.
General Specifications
AttributeValue
Model Number853D 5A II
Rated Power970W
Main Unit DimensionsL250*W190*H137mm ±5mm
Operating Ambient Temp.0~40°C / 32~104°F
OriginMainland China
CertificationCE
Voltage110V, 220V-240V
ColorBlack
Hot Air Rework Station Specifications
AttributeValue
Power650W
Airflow TypeBrushless fan, gentle wind
Airflow Volume≤120L/min
Temperature Range100°C-480°C / 212°F-896°F
Temperature Stability±1°C
Soldering Iron Specifications
AttributeValue
Power60W
Temperature Range200°C-480°C / 392°F-896°F
Temperature Stability±1°C
Tip of Ground Voltage<2mV
Tip Ground Impedance<2 ohm
Iron Heater MaterialHigh-power heater
Iron Handle ColorBlue
DC Power Supply Specifications
AttributeValue
Output Power150W
USB Output Power10W
Output VoltageDC 0~30V ±5%
Output Current0~5A (Adjustable)
Line Regulation<0.067%±2mV
Ripple & NoiseVrms<0.1%
Voltage Setting Accuracy0.1V
Current Setting Accuracy0.01A
Voltage Display Accuracy<0.6%±20mV
Current Display Accuracy<0.6%±2mA
Load Stability<0.01±2mV
Temperature Coefficient<300ppm/°C
Ripple dB<1mvrms (virtual value)

6.1. Compatible Parts

The YIHUA 853D 5A II is compatible with various nozzles and soldering tips. For detailed information on nozzle styles and sizes (QFP, SOP, PLCC, SOJ, BGA(CSP)) and 900M series soldering tips, please refer to the original manual or consult customer service.

Three Preset Channels
Figure 12: The unit features three preset channels for the hot air gun, soldering station, and power supply, allowing for convenient and fast operation.

7. Warranty & Support

This product comes with a 12-month free replacement warranty. Please consult customer service for details.

7.1. Warranty Service Conditions

Warranty service is provided for the following cases:

  1. The item can't power on.
  2. The function can't be operated.
  3. The air gun or soldering iron works abnormally.
  4. The heating element of the air gun or soldering iron is damaged.
  5. The transformer or the fuse holder is damaged.
  6. The order is not in dispute and has not been refunded.
  7. Ensure the item has not been disassembled and repaired.
  8. The buyer should be responsible for the freight of the replacement of the parts.

7.2. User Manual (PDF)

A detailed user manual in PDF format is available for download. You can view it here.

8. User Tips

  • The YIHUA 853D 5A II offers good quality for its price, making it a valuable tool for various soldering and rework tasks.
  • Some models may not include a dedicated mount for all attachments, so users might need to consider alternative storage solutions for accessories like nozzles.
  • The unit has multiple functions including a soldering iron station, hot air gun rework station, and DC power supply, making it a versatile tool for different applications.
  • It operates on both 110V and 220V-240V voltage, ensuring compatibility in various regions.

9. Frequently Asked Questions (FAQ)

Q: What functions does the YIHUA 853D 5A II have?
A: It has multiple functions including a soldering iron station, hot air gun rework station, and DC power supply.
Q: What is the power mode (voltage) of this unit?
A: It operates on 110V and 220V-240V voltage, depending on the specific model purchased.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.