UXCELL Nitrile Rubber O-Rings

Contents

Nitrile Rubber O-Ring Seal Gasket User Manual

Model: Nitrile Rubber O-Rings

1. Introduction

This manual provides essential information for the proper use, installation, and maintenance of your Nitrile Rubber O-Rings. These O-rings are circular in shape with a round cross-section, designed to provide a pressure and fluid seal between mating surfaces.

Made from black Nitrile rubber with a durometer of 70A, these O-rings offer good mechanical properties and high wear resistance. They are suitable for use across a wide temperature range from -4℉ (-20°C) to 212℉ (100°C) and exhibit good resistance to many petroleum oils, greases, hydraulic fluids, mineral oil, and grease.

Single Nitrile O-Ring

Image: A single Nitrile O-ring, illustrating its circular shape and smooth finish.

Pack of 10 Nitrile O-Rings

Image: A pack of 10 Nitrile O-rings, showing multiple units of the product.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight, and weathering. Avoid using O-rings in ozone-generating electric motors, welding equipment, or applications with exposure to UV light.

3. Specifications

  • Material: Nitrile Rubber (NBR)
  • Color: Black
  • Durometer: 70A
  • Standard: Standard
  • Shape: Ring Gasket
  • Temperature Range: -4℉ (-20°C) to 212℉ (100°C)
  • Oil Resistance: Good resistance to many petroleum oils, greases, hydraulic fluids, mineral oil and grease.
  • High-concerned chemical: None
  • Certification: NONE

Dimensions (Thickness CS 2mm)

O-ring dimension diagram

Image: Diagram illustrating the Outer Diameter (OD), Inner Diameter (ID), and Cross-Section (CS) of an O-ring. Example shown: 60mm OD, 56mm ID, 2mm CS.

Table of O-ring dimensions

Image: Table detailing various O-ring inner, outer, and cross-section diameters, all with a 2mm cross-section diameter.

Available O-Ring Sizes (Thickness CS 2mm)
Inner Diameter Outside Diameter Cross-Section Diameter
34mm38mm2mm
35mm39mm2mm
37mm41mm2mm
39mm43mm2mm
40mm44mm2mm
41mm45mm2mm
43mm47mm2mm
44mm48mm2mm
45mm49mm2mm
46mm50mm2mm
48mm52mm2mm
50mm54mm2mm
54mm58mm2mm
56mm60mm2mm
66mm70mm2mm
71mm75mm2mm

4. Installation Instructions

Follow these steps for proper installation of the O-rings:

  1. Inspection: Before installation, carefully check the O-ring for any cracks, deformation, or signs of aging. Do not use damaged O-rings.
  2. Surface Preparation: Ensure the sealing surface is clean and free from any oil, grease, or debris. A clean surface is crucial for an effective seal.
  3. Installation: Install the O-ring into its designated groove evenly. Avoid twisting or stretching the O-ring during installation to prevent damage and ensure a proper fit.

5. Applications

Nitrile O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces. They are widely used in various applications due to their versatility and resistance properties.

Common applications include:

  • Faucets
  • Floor Drains
  • Showers
  • Pipe Interfaces
  • Valves
  • Flanges
  • Various Cylinders
Examples of O-ring applications

Image: Visual examples of common household applications for O-rings, including faucets, floor drains, showers, and pipe interfaces.

6. Maintenance & Storage

  • Avoid Contact: Do not allow O-rings to come into contact with sharp objects, high temperatures, or corrosive media. Such contact can compromise the integrity of the seal.
  • Replacement: If any leakage is detected, replace the O-ring immediately.
  • Storage: Store O-rings in a dry, cool, and dark place. Avoid extrusion or compression during storage to maintain their original shape and sealing properties.

7. Troubleshooting

If you encounter issues with your O-rings, consider the following:

  • Leakage: If leakage occurs, first check if the O-ring is correctly seated in the groove without twisting. Inspect the O-ring for any damage (cracks, cuts, flattening) and replace if necessary. Ensure the mating surfaces are clean and smooth.
  • Improper Fit: If the O-ring does not fit properly, verify that the selected size (Inner Diameter, Outer Diameter, and Cross-Section Diameter) matches the requirements of your application. Refer to the specifications section for available sizes.
  • Premature Wear: If O-rings wear out quickly, check for exposure to incompatible chemicals (acetone, ethers, esters), excessive heat, or UV light, as Nitrile is vulnerable to these conditions.

8. User Tips

  • Always verify the thickness of the O-rings upon arrival, especially if your application requires precise dimensions.
  • For critical applications, use calipers to accurately measure the O-ring dimensions (ID, OD, CS) to ensure they match your requirements.
  • These O-rings have been reported to fit well in specific applications like Maglite model C D head-optical parts and ignition distributors.
  • When using for water filters, double-check the required O-ring thickness. Some water filters may require thicker O-rings (e.g., 3mm or 4mm) than the standard 2mm cross-section provided here.

9. Manufacturer & Support Information

For further assistance or inquiries, please contact the manufacturer or authorized representative:

Manufacturer Information:

  • Company: Guangzhou Dajiali Network Technology Co., Ltd.
  • Address: B395, Room 106, Rulin Street, Tianhe, Guangzhou, China
  • Email: udb7910@126.com

EU Authorized Representative:

  • Company: SUCCESS COURIER SL
  • Address: CALLE RIO TORMESNUM. 1, PLANTAI, DERECHAOFICINA 3Fuenlabrada, Madrid, 28947 Spain
  • Email: successservice2@hotmail.com

A detailed user manual in PDF format is also available for download from the product page.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.