SHIMANO BR-4700

Contents

SHIMANO Tiagra BR-4700 Dual-Pivot Brake Caliper User Manual

Model: BR-4700

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the SHIMANO Tiagra BR-4700 Dual-Pivot Brake Calipers. Designed for road bicycles, these calipers offer reliable braking performance. Please read this manual thoroughly before use to ensure correct installation and safe operation.

SHIMANO Tiagra BR-4700 Dual-Pivot Brake Caliper main product image
SHIMANO Tiagra BR-4700 Dual-Pivot Brake Caliper.

Important Safety Notices

This dealer's manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer's manuals. If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a local bicycle dealer for their assistance.

  • Always read all instruction manuals included with the product.
  • Do not disassemble or modify the product other than as stated in this manual.
  • All dealer's manuals and instruction manuals can be viewed on-line on the Shimano website (http://si.shimano.com).
  • Observe appropriate rules and regulations of your country, state, or region.
  • Always wear safety glasses or goggles to protect your eyes while performing maintenance tasks.
  • Keep this manual in a safe place for later reference.

⚠ DANGER

Failure to follow instructions will result in death or serious injury.

⚠ WARNING

Failure to follow instructions could result in death or serious injury.

⚠ CAUTION

Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.

Setup and Installation

Tools Required

Component Where to Use Tool
BR-4700, BR-4600, BR-3500, BR-2400 Pivot nut 5 mm Allen key
BR-4700, BR-4600, BR-3500, BR-2400 Shoe fixing bolt 4 mm Allen key
BR-4700, BR-4600, BR-3500, BR-2400 Cable fixing bolt 5 mm Allen key
BR-4700, BR-4600, BR-3500, BR-2400 Centering adjustment screw 3 mm Allen key
BL-4700, BL-4600, BL-3500 Clamp bolt 4 mm Allen key
BL-2400, BL-R780 Reach adjustment bolt 2 mm Allen key

1. Installation of the Brake Lever

Use a 4 mm Allen key to install the brake lever. The recommended tightening torque is 6-8 N-m (53-69 in. lbs.).

Note: Even with the recommended tightening torque, carbon handlebars may become damaged if not handled correctly. Confirm the appropriate torque with your bicycle or handlebar manufacturer. Use a handlebar grip with a maximum outer diameter of 32 mm.

Diagram showing brake lever installation with a 4mm Allen key and tightening torque
Brake lever installation using a 4mm Allen key. Tightening torque: 6-8 N-m (53-69 in. lbs.).

2. Installation of the Brake Cable

Cut the cable to a length that allows for some slack even when the handlebars are turned fully to both sides.

Diagram showing brake cable routing through outer casing and inner cable drum with cable hook
Diagram illustrating brake cable routing: outer casing, inner cable drum, and cable hook.

3. Installation of the Caliper Brake

Refer to the Caliper Brake section of General Operations for detailed installation instructions.

Securely tighten the caliper brake mounting nuts to the specified tightening torque. Use lock nuts with nylon inserts (self-locking nuts) for nut-type brakes. For sunken nut type brakes, use sunken nuts of the appropriate length which can be turned six times or more; when re-installing, apply sealant (locking adhesive) to the nut threads. If the nuts become loose and the brakes fall off, they may get caught up in the bicycle and the bicycle may fall over. Particularly if this happens with the front wheel, the bicycle may be thrown forward and serious injury could result.

Brakes designed for use as rear brakes should not be used as front brakes.

4. Initial Check

After installing the brake cable on the caliper brake, hold the brake lever and press it about ten times until it touches the grip. This checks for proper shoe clearance and ensures all sections are functioning correctly before use.

Diagram showing how to check brake lever by pressing it about 10 times
Checking brake lever function by pressing it approximately 10 times.

Operating Instructions

  • Each bicycle may handle differently depending on the product. Fully understand and get used to the operation of your bicycle's brake system, including brake lever pressure and control characteristics.
  • Improper use of your bicycle's brake system may result in loss of control or a fall, leading to severe injury. Consult a professional bicycle dealer or read the owner's manual for proper operation. Practice braking operation and other basic features.
  • Applying the front brake too strongly can lock the wheel, causing the bicycle to fall forward and potentially severe injury.
  • Always ensure both front and rear brakes are working correctly before riding.
  • Braking distance will be longer in wet weather. Reduce your speed and apply brakes early and gently.
  • If the road surface is wet, tires will skid more easily. Reduce speed and apply brakes early and gently to avoid skidding and falling.

Maintenance

Reach Adjustment

Adjust the brake lever reach using a 2 mm Allen key. Turning clockwise narrows the width, while turning counter-clockwise widens it.

Diagram showing brake lever reach adjustment with a 2mm Allen key, narrowing the reach
Adjusting brake lever reach: clockwise to narrow.
Diagram showing brake lever reach adjustment with a 2mm Allen key, widening the reach
Adjusting brake lever reach: counter-clockwise to widen.

Mode Switching (BL-4700/4600/3500/2400/R780)

The brake levers are equipped with a mode switching mechanism to ensure compatibility with various brake types (V-BRAKE, caliper, cantilever, and road mechanical disc brakes). The specific mechanism may vary by model. Selecting the incorrect mode can lead to excessive or insufficient braking force, which is dangerous. Always select the mode according to the instructions in the mode switching table below.

For BR-4700/4600/3500/2400, use the dual control lever or brake lever according to the combination specified in the following table. Do not use combinations marked with "NO!" as this can lead to excessively effective brakes and potential falls.

Mode Position Applicable Brake
V position V-BRAKE
C/R position Caliper brakes, Cantilever brakes, Road mechanical disc brakes

Brake Lever and Caliper Combination Table

Brake Caliper Compatibility Dual Control Lever Brake Lever
BR-4700 OK ST-4600, ST-4603, ST-3500, ST-3503, ST-2400, ST-2403 BL-4700, BL-4600, BL-3500, BL-2400, BL-R780 (*)
BR-4600, BR-3500, BR-2400 OK ST-4600, ST-4603, ST-3500, ST-3503, ST-2400, ST-2403 BL-4700, BL-4600, BL-3500, BL-2400, BL-R780 (*)
Any BR- model NO! Dual control lever for road bikes other than the above Brake lever for road bikes other than the above

(*) BL-R780 is a brake lever for flat handle. "NO!" indicates combinations that should not be used under any circumstances.

Diagram showing loosening screw for mode switching
Step 1: Use a screwdriver #1 to loosen the screw for mode switching.
Diagram showing aligning mode switch with brake position
Step 2: Align the mode switch with the position of the installed brake type.

Brake Shoe Characteristics

Different brake shoes have varying characteristics. Consult your dealer for details when purchasing replacement brake shoes. When combined with a ceramic rim, Shimano standard brake shoes wear down more quickly. Replace brake shoes when the grooves are no longer visible.

Characteristic R55C4 R55C2 R55C3 R55C (Carbon) R55C-1 (Carbon) R55C+1 M50T R50T R50T2 R50T4 R50T5
Cartridge type X X X - X X X - - - -
Recommended rim Aluminum Aluminum Aluminum Carbon Carbon Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum
DRY Power ★★★★★ ★★★★★ ★★★★★ ★★★★☆ ★★★★☆ ★★★★☆ ★★★☆☆ ★★★★☆ ★★★★☆ ★★★★☆ ★★★★★
WET Power ★★☆☆☆ ★★☆☆☆ ★★☆☆☆ ★★★☆☆ ★★★☆☆ ★★☆☆☆ ★★★★☆ ★★☆☆☆ ★★☆☆☆ ★★★☆☆ ★★☆☆☆
Silence ★★★★☆ ★★★★☆ ★★★★☆ ★★★☆☆ ★★★☆☆ ★★★★☆ ★★★★★ ★★★★☆ ★★★★☆ ★★★★☆ ★★★★☆
Anti-fading ★★★★★ ★★★★★ ★★★★★ ★★★★★ ★★★★★ ★★★★★ ★★★★☆ ★★★★☆ ★★★★☆ ★★★★☆ ★★★★★
Durability (on road) ★★★★★ ★★★★★ ★★★★★ ★★★★★ ★★★★☆ ★★★★☆ ★★★★☆ ★★★☆☆ ★★★☆☆ ★★★☆☆ ★★★★☆
Durability (muddy condition) ★★★★★ ★★★★★ ★★★★☆ ★★★★☆ ★★★★☆ ★★★☆☆ ★★☆☆☆ ★★☆☆☆ ★★☆☆☆ ★★☆☆☆ ★★★★☆
Anti rim-attack ★★★★★ ★★★★★ ★★★★☆ ★★★★☆ ★★★★☆ ★★★★★ ★★★☆☆ ★★★★★ ★★★★★ ★★★★★ ★★★★★

Note: 'X' indicates Cartridge type, '-' indicates not applicable. Stars indicate performance level, with 5 stars being excellent.

For maximum performance, we highly recommend using Shimano lubricants and maintenance products.

Troubleshooting

  • Brakes not working correctly: Check for oil or grease on the brake shoes. If present, contact your place of purchase or a bicycle dealer for assistance.
  • Brake cable issues: Regularly check the brake cable for rust, fraying, and cracks. If any problems are found, contact your place of purchase or a bicycle dealer. Damaged cables can lead to brake failure.
  • Loose nuts: Ensure all caliper brake mounting nuts are securely tightened to the specified torque. Loose nuts can cause the brakes to fall off, potentially leading to serious injury, especially if it happens with the front wheel.
  • Incompatible components: Ensure your brake levers and calipers are compatible. Using incompatible combinations (marked "NO!" in the mode switching table) can result in dangerous braking performance.

Specifications

Attribute Detail
Brand Name SHIMANO
Model Number BR-4700
Use Road Bicycles
Material Light Alloy
Braking System V Brake (Friction Wheel Brake)
Components Caliper Brake
High-concerned chemical None
Origin Malaysia
Approximate Weight (Single Caliper) 383 grams (as per user image)
Package Weight 0.6 kg
Package Dimensions (L x W x H) 20 cm x 15 cm x 15 cm
Brake caliper on a digital scale showing a weight of 383 grams
Weight of a single brake caliper (383g shown on scale).

User Tips

  • Many users report excellent quality and performance, often noting the brakes are sharp and effective.
  • The product is frequently described as original Shimano, even if it doesn't come in branded retail packaging.
  • Ensure compatibility with your bike's components, especially if you have an older model or specific brake lever types (e.g., Ltwoo R7). Some users have noted potential compatibility issues requiring custom brackets.
  • The calipers are generally lightweight; a single caliper weighs approximately 383g.
  • Proper packaging is often highlighted, ensuring the product arrives in good condition.

Frequently Asked Questions (FAQ)

Q: Is this brake caliper compatible with Ltwoo R7 controllers?
A: Compatibility with specific third-party controllers like Ltwoo R7 is not explicitly stated in the official documentation. It is recommended to consult a professional bicycle mechanic or the manufacturer of your Ltwoo R7 controller to confirm compatibility before purchase and installation.
Q: How much does a pair of these brake calipers weigh?
A: Based on user-provided images, a single caliper weighs approximately 383 grams. Therefore, a pair would weigh around 766 grams.

Warranty and Support

Products are not guaranteed against natural wear and deterioration from normal use and aging. For any issues or support, please contact Shimano directly or your local bicycle dealer.

SHIMANO Contact Information:

  • SHIMANO AMERICAN CORPORATION
    One Holland, Irvine, California 92618, U.S.A.
    Phone: +1-949-951-5003
  • SHIMANO EUROPE B.V.
    Industrieweg 24, 8071 CT Nunspeet, The Netherlands
    Phone: +31-341-272222
  • SHIMANO INC.
    3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

Please note: specifications are subject to change for improvement without notice. This manual was published in Feb. 2015 by Shimano Inc. HTR.

A user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.