1. Introduction
Thank you for purchasing the BAOFENG UV-5RA Amateur Portable Radio. This is a dual band/dual display radio designed to provide secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use to ensure maximum performance from your radio.
2. Safety Information
The following safety precautions must always be observed during operation, service, and repair of this equipment:
- This equipment shall be serviced by qualified technicians only.
- Do not modify the radio for any reason.
- Use only supplied or approved batteries and chargers.
- Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
- Turn off your radio prior to entering any area with explosive and flammable materials.
- Do not charge your battery in a location with explosive and flammable materials.
- To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
- Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
- Turn off your radio before entering a blasting area.
- For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.
- Do not expose the radio to direct sunlight over a long time, nor place it close to heating source.
- When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips.
- Keep antenna at least 2.5 centimeters away from your body when transmitting.
WARNING:
If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.
3. Features and Functions
Image: List of key features for the BAOFENG UV-5RA transceiver.
- Dual-band handheld transceiver with LCD display.
- DTMF encoded.
- High capacity Lithium-ion battery.
- Commercial FM radio receiver (65 MHz ~ 108 MHz).
- Incorporates 105 DCS codes and 50 CTCSS privacy codes (programmable).
- VOX function (voice operated transmission).
- Alarm function.
- Up to 128 memory channels.
- Broadband (Wide) / Narrowband (Narrow) selectable.
- High power/low (5 W/1 W) selectable.
- Display illumination and programmable keyboard.
- Keypad beep function.
- Dual Watch/dual reception.
- Selectable Frequency Step: 2.5/5/6.25/10/12.5/25 kHz.
- OFFSET function (frequency offset for repeater access).
- Battery saving function "SAVE".
- Timer transmission "TOT" programmable.
- Scan Mode selection.
- Busy Channel Lock "BCLO" function.
- Built-in RX CTCSS/DCS scan.
- Built-in LED flashlight.
- Programmable by PC.
- Squelch Level Threshold adjustable from 0 to 9.
- Crossband reception.
- Tone end of transmission.
- Built-in key lock.
4. Unpacking and Checking Equipment
Carefully unpack the transceiver. We recommend that you identify the items listed below before discarding the packing material. If any items are missing or have been damaged during shipment, please contact your dealer immediately.
Image: Display of included accessories: User's Manual, Antenna, Battery, Clip/Lanyard, Headset, Charger Base, and Power Adapter.
Standard Package Contents:
- BAOFENG UV-5RA Transceiver
- Antenna
- Li-ion Battery Pack (1800mAh)
- Desktop Charger
- Power Adapter
- Belt Clip
- Hand Strap/Lanyard
- User's Manual
- Earphone/Headset
Note: Items included in the package may differ depending on the country of purchase. Consult your dealer for more information.
5. Setup
5.1. Installing the Antenna
Install the antenna as shown in the figure below and turn it clockwise until it stops.
Image: Diagram showing how to screw the antenna onto the top of the radio.
- When installing the antenna, do not rotate it by its top; hold it by its base and turn.
- If you use an external antenna, make sure the 'SWR' is about 1.5:1 or less, to avoid damage to the transceiver's final transistors.
- Do not hold the antenna with your hand or wrap the outside of it to avoid bad operation of the transceiver.
- Never transmit without an antenna.
5.2. Installing the Belt Clip
If necessary, install the belt clip at the rear of the battery compartment cover as shown in the figure below.
Image: Diagram showing the belt clip being attached to the back of the radio with screws.
Note:
Do not use any kind of glue to fix the screw on the belt clip. The solvents in glue may damage the battery casing.
5.3. Micro-Headset Installation
Plug the external micro-headset connector into the jack of 'SP. & MIC' of the transceiver as shown in the figure below.
Image: Diagram showing a micro-headset plug inserted into the side jack of the radio.
5.4. Battery Installation
Image: Diagram illustrating how to slide the battery pack onto the radio body.
- When attaching the battery, make sure the battery is in parallel and in good contact with the aluminum chassis. The battery bottom should be about 1 to 2 centimeters below the bottom of the radio's body.
- Align the battery with the guide rails on the aluminum chassis and slide it upwards until a 'click' is heard.
- The battery latch at the bottom locks the battery.
Removing the Battery:
- Turn off the radio before removing the battery.
- Slide the battery latch, at the bottom of the radio's body, in the direction indicated by the arrow.
- Slide down the battery for about 1 to 2 centimeters, and then remove the battery from the radio's body.
6. Battery Charging
Use only the charger specified by the manufacturer. The charger's LED indicates the charging progress.
Image: The BAOFENG UV-5RA radio placed in its charging cradle, connected to a power adapter.
Charging Steps:
- Plug the power cord into the adapter.
- Plug the AC connector of the adapter into the AC outlet socket.
- Plug the DC connector of the adapter into the DC socket on the back of the charger.
- Place the radio with the battery attached, or the battery alone, in the charger.
- Make sure the battery is in good contact with the charging terminals. The charging process initiates when the red LED lights.
- The green LED lights about 4 hours later, indicating the battery is fully charged. Then remove the radio with the battery attached or the battery alone from the charger.
LED Indication:
| Charging Status | LED Indication |
|---|---|
| Standby (no-load) | Red LED flashes, while Green LED glows |
| Charging | Red LED solidly glows |
| Fully Charged | Green LED solidly glows |
| Error | Red LED flashes, while Green LED glows |
Initial Use:
New batteries are shipped uncharged from the factory. Charge a new battery for 5 hours before initial use. The maximum battery capacity and performance are achieved after three full charge/discharge cycles. If you notice the battery power runs low, please recharge the battery.
WARNING:
- To reduce the risk of injury, charge only the battery specified by the manufacturer. Other batteries may burst, causing bodily injury and property damage.
- To avoid risk of personal injury, do not dispose of batteries in a fire!
- Dispose of batteries according to local regulations (e.g., recycling). Do not dispose as household waste.
- Never attempt to disassemble the battery.
7. Operating Instructions
7.1. Radio Overview (Parts, Controls, and Keys)
Image: Diagram labeling the parts of the BAOFENG UV-5RA, including Antenna, Flashlight, Power/Vol knob, SP/MIC jack, LCD, Dual Display, Call button, PTT button, MONI button, and Keypad.
| No. | Part | No. | Part |
|---|---|---|---|
| 1. | Antenna | 10. | Strap Buckle |
| 2. | Flashlight | 11. | Accessory Jack |
| 3. | Knob (ON/OFF, Volume) | 12. | A/B Key (Frequency Display Switches) |
| 4. | LCD | 13. | BAND Key (Band Switches) |
| 5. | SK-side Key1/CALL (Radio, Alarm) | 14. | Keypad |
| 6. | SK-side Key2/MONI (Flashlight, Monitor) | 15. | SP. & MIC. |
| 7. | PTT Key (Push-to-Talk) | 16. | Battery Pack |
| 8. | VFO/MR (Frequency Mode/Channel Mode) | 17. | Battery Contacts |
| 9. | LED Indicator | 18. | Battery Remove Button |
7.2. Command/Key Definition
- [PTT] (PUSH-TO-TALK): Press and hold down the [PTT] button to transmit; release it to receive.
- SK-SIDE KEY1/[CALL]:
- Press the [CALL] button to activate the FM Radio; Press it again to deactivate the FM Radio.
- Press and hold on the [CALL] button to activate the alarm function; Press and hold it again to deactivate the alarm function.
- SK-SIDE KEY2/[MONI]:
- Press the [MONI] button to turn on the flashlight; Press it again to turn off.
- Press and hold on the [MONI] button to monitor the signal.
- [VFO/MR] BUTTON: Press the [VFO/MR] button to switch between frequency mode and channel mode.
- [A/B] BUTTON: Press the [A/B] button to switch frequency display.
- [BAND] BUTTON:
- Press the [BAND] button to switch band display.
- While FM radio is activated, press the [BAND] button to switch the band of FM radio (band 65-75MHz/76-108MHz).
- [*SCAN] KEY:
- Press the [*SCAN] key to activate the Reverse function; it will exchange a separate reception and transmission frequency.
- Press the [*SCAN] key for 2 seconds to start scanning (frequency/channel).
- While FM radio is activated, press the [*SCAN] key to search FM radio stations.
- While setting the RX CTCSS/DCS, press the [*SCAN] key to scan the RX CTCSS/DCS.
- [#] KEY:
- Under channel mode, press [#] key to switch High/Low transmit power.
- Press [#] key for 2 seconds to lock/unlock the keypad.
- ACCESSORY JACK: The jack is used to connect audio accessories, or other accessories such as programming cable.
7.3. LCD Display
The display icons appear when certain operations or specific features are activated.
Image: Diagram showing the various icons and their meanings on the LCD display.
| Icon | Description |
|---|---|
| Operating channel. | |
| 75 25 | Operating frequency. |
| CT | 'CTCSS' activated. |
| DCS | 'DCS' activated. |
| +- | Frequency offset direction for accessing repeaters. |
| S | Dual Watch/Dual Reception functions activated. |
| VOX | Function 'VOX' enabled. |
| R | Reverse function activated. |
| N | Wide Band selected. |
| Battery Level indicator | |
| Keypad lock function activated. | |
| L | Low transmit power. |
| Operation frequency. | |
| Yull | Signal Strength Level. |
7.4. 1750 Hz Tone for Access to Repeaters
To establish long-distance communications through an amateur radio repeater that is activated by a 1750 Hz tone: Press and hold the [PTT] button, then press the [BAND] button to transmit a 1750Hz tone.
7.5. Basic Operation
Radio ON-OFF/Volume Control:
- Make sure the antenna and battery are installed correctly and the battery is charged.
- Rotate the knob clockwise to turn the radio on.
- Rotate the knob fully counter-clockwise until a 'click' is heard to turn the radio off.
- Turn the knob clockwise to increase the volume, or counter-clockwise to decrease the volume.
Selecting a Frequency or Channel:
- Press the [▲] or [▼] key to select the desired frequency/channel. The display shows the selected frequency/channel.
- Press and hold down the [▲] or [▼] key for fast frequency up or down.
- Note: You cannot select a channel if not previously stored.
7.6. Advanced Operation (Set Menu Description)
You can program your transceiver operating in the setup menu to suit your needs or preferences.
| Menu No. | Function/Description | Available Settings |
|---|---|---|
| 0 | SQL (Squelch level) | 0-9 |
| 1 | STEP (Frequency step) | 2.5/5/6.25/10/12.5/25kHz |
| 2 | TXP (Transmit power) | HIGH/LOW |
| 3 | SAVE (Battery save, 1:1/1:2/1:3/1:4) | OFF/1/2/3/4 |
| 4 | VOX (Voice operated transmission) | OFF/0-10 |
| 5 | W/N (Wideband/narrowband) | WIDE/NARR |
| 6 | ABR (Display illumination) | OFF/1/2/3/4/5s |
| 7 | TDR (Dual watch/dual reception) | OFF/ON |
| 8 | BEEP (Keypad beep) | OFF/ON |
| 9 | TOT (Transmission timer) | 15/30/45/60.../585/600seconds |
| 10 | R-DCS (Reception digital coded squelch) | OFF/D023N...D7541 |
| 11 | R-CTS (Reception Continuous Tone Coded Squelch) | 67.0Hz...254.1Hz |
| 14 | VOICE (Voice prompt) | OFF/ON |
| 15 | ANI (Automatic number identification of the radio, only can be set by PC software.) | |
| 16 | DTMFST (The DTMF tone of transmitting code.) | OFF/DT-ST/ANI-ST/DT+ANI |
| 17 | S-CODE (Signal code, only could be set by PC software.) | 1,...,15 groups |
| 18 | SC-REV (Scan resume method) | TO/CO/SE |
| 19 | PTT-ID (press or release the PTT button to transmit the signal code) | OFF/BOT/EOT/BOTH |
| 20 | PTTLT (delay the signal code sending) | 0,...,30ms |
| 21 | MDF-A (under channel mode, A channel displays. Note:name display only can be set by PC software.) | FREQ/CH/NAME |
| 22 | MDF-B (under channel mode, B channel displays. Note:name display only can be set by PC software.) | FREQ/CH/NAME |
| 23 | BCL (busy channel lockout) | OFF/ON |
| 24 | AUTOLK (keypad locked automatically) | OFF/ON |
| 25 | SFT-D (direction of frequency shift) | OFF/+/- |
| 26 | OFFSET (frequency shift) | 00.000...69.990 |
| 27 | MEMCH (stored in memory channels) | 000,...127 |
| 28 | DELCH (delete the memory channels) | 000, ...127 |
| 29 | WT-LED (illumination display color of standby) | OFF/BLUE/ORANGE/PURPLE |
| 30 | RX-LED (illumination display color of reception) | OFF/BLUE/ORANGE/PURPLE |
| 31 | TX-LED (illumination display color of transmitting) | OFF/BLUE/ORANGE/PURPLE |
| 32 | AL-MOD (alarm mode) | SITE/TONE/CODE |
| 33 | BAND (band selection) | VHF/UHF |
| 34 | TX-AB (transmitting selection while in dual watch/reception) | OFF/A/B |
| 35 | STE (Tail Tone Elimination) | OFF/ON |
| 36 | RP_STE (Tail tone elimination in communication through repeater) | OFF/1,2,3...10 |
| 37 | RPT_RL (Delay the tail tone of repeater) | OFF/1,2,3...10 |
| 38 | PONMGS (Boot display) | FULL/MGS |
| 39 | ROGER (tone end of transmission) | ON/OFF |
| 40 | RESET (Restore to default setting) | VFO/ALL |
7.7. Shortcut Menu Operation
- Press the [MENU] key, then press the [▲] or [▼] key to select the desired menu.
- Press the [MENU] key again to enter parameter setting.
- Press the [▲] or [▼] key to select the desired parameter.
- Press the [MENU] key to confirm and save, or press the [EXIT] key to cancel setting or clear the input.
7.8. Squelch (SQL)
The squelch mutes the speaker of the transceiver in the absence of reception. With the squelch level correctly set, you will hear sound only while actually receiving signals and significantly reduce battery current consumption. It is recommended that you set Level 5.
7.9. VOX (Voice Operated Transmission)
This function allows transmission without pressing the [PTT] button. Transmission is activated automatically by detecting the radio voice. When speaking finishes, the transmission is automatically terminated, and the transceiver will automatically receive signals. Be sure to adjust the VOX Gain level to an appropriate sensitivity for smooth transmission.
7.10. Select Wideband or Narrowband (W/N)
In areas where RF signals are saturated, use the narrow band of transmission to avoid interference in adjacent channels.
7.11. TDR (Dual Watch/Dual Reception)
This feature allows you to operate between frequency A and frequency B. Periodically, the transceiver checks whether a signal is received on another scheduled frequency. If a signal is received, the unit will remain on that frequency until the signal disappears.
7.12. TOT (Transmission Timer)
This function automatically controls the transmission time each time you press [PTT]. This feature is useful to avoid overheating excessive power transistors. The transceiver will automatically stop transmitting once the set time is reached.
7.13. CTCSS/DCS
In some cases, to establish communications in a closed user group at a particular frequency or channel, you can use "CTCSS" or "DCS" codes for reception. The squelch opens only when receiving a frequency with the same CTCSS or DCS codes as programmed in your transceiver. If the received signal codes differ, the squelch will not open, and the received signal will not be heard.
Note:
The use of "CTCSS" or "DCS" in communication does not guarantee complete confidentiality.
CTCSS Table:
| No. | Tone (Hz) | No. | Tone (Hz) | No. | Tone (Hz) | No. | Tone (Hz) | No. | Tone (Hz) |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 67.0 | 11 | 94.8 | 21 | 131.8 | 31 | 171.3 | 41 | 203.5 |
| 2 | 69.3 | 12 | 97.4 | 22 | 136.5 | 32 | 173.8 | 42 | 206.5 |
| 3 | 71.9 | 13 | 100.0 | 23 | 141.3 | 33 | 177.3 | 43 | 210.7 |
| 4 | 74.4 | 14 | 103.5 | 24 | 146.2 | 34 | 179.9 | 44 | 218.1 |
| 5 | 77.0 | 15 | 107.2 | 25 | 151.4 | 35 | 183.5 | 45 | 225.7 |
| 6 | 79.7 | 16 | 110.9 | 26 | 156.7 | 36 | 186.2 | 46 | 229.1 |
| 7 | 82.5 | 17 | 114.8 | 27 | 159.8 | 37 | 189.9 | 47 | 233.6 |
| 8 | 85.4 | 18 | 118.8 | 28 | 162.2 | 38 | 192.8 | 48 | 241.8 |
| 9 | 88.5 | 19 | 123.0 | 29 | 165.5 | 39 | 196.6 | 49 | 250.3 |
| 10 | 91.5 | 20 | 127.3 | 30 | 167.9 | 40 | 199.5 | 50 | 254.1 |
DCS Table:
| No. | Code | No. | Code | No. | Code | No. | Code | No. | Code |
|---|---|---|---|---|---|---|---|---|---|
| 1 | D023N | 22 | D131N | 43 | D251N | 64 | D371N | 85 | D532N |
| 2 | D025N | 23 | D132N | 44 | D252N | 65 | D411N | 86 | D546N |
| 3 | D026N | 24 | D134N | 45 | D255N | 66 | D412N | 87 | D565N |
| 4 | D031N | 25 | D143N | 46 | D261N | 67 | D413N | 88 | D606N |
| 5 | D032N | 26 | D145N | 47 | D263N | 68 | D423N | 89 | D612N |
| 6 | D036N | 27 | D152N | 48 | D265N | 69 | D431N | 90 | D624N |
| 7 | D043N | 28 | D155N | 49 | D266N | 70 | D432N | 91 | D627N |
| 8 | D047N | 29 | D156N | 50 | D271N | 71 | D445N | 92 | D631N |
| 9 | D051N | 30 | D162N | 51 | D274N | 72 | D446N | 93 | D632N |
| 10 | D053N | 31 | D165N | 52 | D306N | 73 | D452N | 94 | D645N |
| 11 | D054N | 32 | D172N | 53 | D311N | 74 | D454N | 95 | D654N |
| 12 | D065N | 33 | D174N | 54 | D315N | 75 | D455N | 96 | D662N |
| 13 | D071N | 34 | D205N | 55 | D325N | 76 | D462N | 97 | D664N |
| 14 | D072N | 35 | D212N | 56 | D331N | 77 | D464N | 98 | D703N |
| 15 | D073N | 36 | D223N | 57 | D332N | 78 | D465N | 99 | D712N |
| 16 | D074N | 37 | D225N | 58 | D343N | 79 | D466N | 100 | D723N |
| 17 | D114N | 38 | D226N | 59 | D346N | 80 | D503N | 101 | D731N |
7.14. PTT-ID (PTT or Release PTT to Transmit the Signal Code)
This feature allows you to know who is calling you.
- OFF: Does not transmit the code while pushing the PTT button.
- BOT: Transmits the code while pushing the PTT button (code can only be set by PC software).
- EOT: Transmits the code while releasing the PTT button.
- BOTH: Transmits the code while pushing or releasing the PTT button.
7.15. BCL (Busy Channel Lockout)
The BCLO feature prevents the radio's transmitter from being activated if a signal strong enough to break through the "noise" squelch is present. On a frequency where stations using different CTCSS or DCS codes may be active, BCLO prevents you from disrupting their communications accidentally (because your radio may be muted by its own tone decoder).
7.16. SFT-D (Direction of Frequency Shift)
The "OFFSET" is the difference or offset between the reception frequency and the transmission frequency for access to amateur radio repeaters. Set the "OFFSET" according to the repeater through which you want to communicate.
7.17. OFFSET (Frequency Shift)
When communicating via a repeater, the direction of frequency displacement should be timed to ensure the transmission frequency is higher or lower than the receiving frequency.
7.18. STE (Tail Tone Elimination)
This function activates or deactivates the transmission end tone of the transceiver. This final tone transmission should only be used in communications between transceivers and not in communications through a repeater, which must be deactivated.
8. Maintenance
8.1. Battery Tips:
- When charging your battery, keep it at a temperature between 5°C - 40°C. Temperatures outside this limit may cause battery leakage or damage.
- When charging a battery attached to a radio, turn the radio off to ensure a full charge.
- Do not cut off the power supply or remove the battery when charging.
- Never charge a wet battery. Dry it with a soft cloth prior to charging.
- The battery will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal performance, it is time to buy a new battery.
8.2. Prolonging Battery Life:
- Battery performance will be greatly decreased at temperatures below 0°C. A spare battery is necessary in cold weather. A cold battery unable to work in this situation may work under room temperature, so keep it for later use.
- Dust on the battery contacts may prevent the battery from working or charging. Use a clean dry cloth to wipe it before attaching the battery to the radio.
8.3. Battery Storage:
- Fully charge a battery before storing it for a long time to avoid damage due to over-discharge.
- Recharge a battery after several months' storage (Li-Ion batteries: 6 months) to avoid battery capacity reduction due to over-discharge.
- Store your battery in a cool and dry place under room temperature to reduce self-discharge.
9. Troubleshooting
| Problem | Possible Cause / Solution |
|---|---|
| The radio does not start. | The battery is low; replace it with a charged battery or proceed to charge the battery. The battery is not installed correctly; remove and reattach it. |
| The battery runs down quickly. | The battery life has come to an end; replace the battery with a new one. The battery is fully charged, but not made in full; ensure the battery is fully charged. |
| The receiving indicator LED lights but no sound from the speaker. | Make sure the volume setting is not too low. Ensure the undertones "CTCSS" or code "DCS" are the same as those programmed in the transceiver of the other members of your group. |
| When transmitting, other members of the group do not receive the communication. | Ensure the undertones "CTCSS" or code "DCS" programmed in your transceiver are the same as those programmed in the transceiver of the other members of your group. Your partner or you are too far away, or in a bad area of RF signal propagation. |
| In "standby" mode, the transceiver transmits without pressing the "PTT". | Check if the VOX level adjustment function is not set too sensitive. |
| Receiving communications from other user groups while communicating with your group. | Change frequency or channel. Change the undertones "CTCSS" or code "DCS" in your group. |
| Communication with other members of your group is poor or low quality. | You or your partner is too far away or in an area of poor radio signal propagation, such as inside a tunnel, an underground car park, a mountainous area, or near large metal structures. |
If these checks do not resolve the issue, please contact your distributor, dealer, or service center.
10. Technical Specifications
Image: Table summarizing the technical parameters of the BAOFENG UV-5RA.
10.1. General:
| Parameter | Value |
|---|---|
| Frequency Range | 65MHz-108MHz (Commercial FM radio reception only), VHF: 136MHz-174MHz (Rx/Tx), UHF: 400MHz-480MHz (Rx/Tx) |
| Memory Channels | Up to 128 channels |
| Frequency Stability | 2.5ppm |
| Frequency Step | 2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/25kHz |
| Antenna Impedance | 50 Ω |
| Operating Temperature | -20°C to +60°C |
| Supply Voltage | Rechargeable Lithium-Ion mAh 7.4V/1800 |
| Consumption in Standby | ≤ 75mA |
| Consumption in Reception | 380mA |
| Consumption in Transmission | ≤ 1.4A |
| Mode of Operation | Simplex or semi-duplex |
| Duty Cycle | 03/03/54 min. (Rx / Tx / Standby) |
| Dimensions | 58mm x 110mm x 32mm |
| Weight | 130 g (approximate) |
10.2. Transmitter:
| Parameter | Value |
|---|---|
| RF Power | 5W/1W |
| Type of Modulation | FM |
| Emission Class | 16KΦF3E/11KΦF3E (W/N) |
| Maximum Deviation | ≤ ± 5 kHz/ ≤ ± 2.5 kHz (W/N) |
| Spurious Emissions | <-60 dB |
10.3. Receiver:
| Parameter | Value |
|---|---|
| Receiver Sensitivity | 0.2 μV (at 12 dB SINAD) |
| Intermodulation | 60 dB |
| Audio Output | 1000mW |
| Adjacent Channel Selectivity | 65/60dB |
Note:
All specifications shown are subject to change without notice.
11. Warranty and Support
The device described in this Certificate is guaranteed for a period of one year from the date of sale to the final user. This Warranty Certificate is unique and not transferable and may not be reissued for new or original or copy. Substitution of product failure or any part thereof shall not involve extension of the guarantee.
The warranty covers the replacement and free replacement of all parts that are defective in materials and components used in manufacturing and/or assembly of the apparatus.
The warranty does not cover any faults caused by accident, improper installation and use, electric shock (e.g., storms), connecting to a power source other than specified, reverse polarity in the diet, or claims due to deterioration in the external appearance of normal use, nor the amount or condition of the accessories.
Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.
The warranty does not cover rechargeable batteries even if they are part of the equipment purchased as they are considered consumables. Any impairment must be reported within a period of fifteen days from the date of purchase.
The warranty is void on the following assumptions:
- Devices that have been manipulated by another or by anyone other than an authorized service provider.
- Equipment and accessories in which the serial number has been altered, deleted, or filed unreadable.
- Use of the product other than as intended.
To make use of the guarantee, it is necessary to provide the dealer or any of the Authorized Service with the defective device, its accessories, and the following documentation:
- Warranty Certificate duly completed and sealed.
- Original invoice which clearly identifies the device and the date of purchase.
- Description of the faults.
The warranty terms contained in this Certificate of Guarantee do not exclude, modify, or restrict the statutory rights of the buyer by virtue of the laws in force at the time of purchase, but are added to them.
For detailed warranty information and support, please refer to the official user manual PDF: BAOFENG UV-5RA User Manual (PDF).
12. Product Video
Watch this video for a visual overview and demonstration of the BAOFENG UV-5RA Dual Band FM Transceiver.
Video: A demonstration of the BAOFENG UV-5RA walkie talkie, showcasing its physical features and basic handling.