NOPARDE GD/GJ/GS

Contents

NOPARDE Gobo Projection Lamp User Manual

Waterproof Outdoor Gobo Projection Lamp Customized Advertising Image LED Door Head Static Logo Projector

1. Introduction

This manual provides essential information for the safe and effective use of your NOPARDE Gobo Projection Lamp. Designed for both indoor and outdoor advertising, this projector allows for customizable image projection, enhancing visibility and appeal for businesses and events.

The NOPARDE Gobo Projection Lamp is an integrated advertising projection lamp with an upgraded appearance and free design options. It features a six-piece coated optical lens for ultra-clear projection and is built with a fully enclosed aluminum alloy for integrated waterproof and dustproof protection.

Two NOPARDE Gobo Projection Lamps, one black and one silver, showcasing their integrated design.
Integrated Advertising Projection Lamp Design

2. Safety Information

  • Projectors that are not waterproof should not be installed in places where they can get wet outdoors.
  • If there is any problem with the product, please contact customer service in time, and do not disassemble by yourself.
  • Remember to tighten the "waterproof fixing iron ring" for the waterproof Projector. Otherwise, after the lens is used for a long time, rain will slowly percolate into it, affecting the quality of projection imaging.

3. Setup and Installation

3.1. Mounting the Projector

Use the provided screws to fix the bracket to the wall, ceiling, or embed it as required.

Diagram showing three steps for minimal installation: screw mounting bracket, adjust bracket direction, and rotate lens to adjust sharpness.
Minimal Installation Steps
  1. Screw Mounting Bracket: Securely attach the mounting bracket to your desired surface.
  2. Adjust the Bracket Direction: The projector features 360° no dead angle adjustment. Adjust the bracket to point the projector in the desired direction. This can be done by hand screwing without tools.
  3. Rotate the Lens to Adjust the Sharpness: Rotate the lens to achieve a clear and sharp projection.
Image showing the projector mounted with a bracket, illustrating its 360-degree rotation capability.
360° Rotation for Flexible Adjustment

3.2. Power Connection

Plug in the power switch. The light will turn on. Note that the projector has no remote control by default, and the non-remote control can be plugged in directly.

3.3. Adjusting Projection Clarity

After the light is on, adjust the clarity of the projection by twisting the lens outwards. Be careful not to let it fall to the ground. For indoor use, adjusting from 2 to 3 meters is recommended. For outdoor commissioning during the day, first unscrew the stand, adjust the angle, and then tighten it again. The bracket with adjustment screws can be operated with the included hex wrench.

A NOPARDE Gobo Projector mounted on a wall, with rain effects, highlighting its IP65 waterproof rating and suitability for 24-hour outdoor use.
Integrated Waterproof and Dustproof Design (IP65)

For a visual guide on installation and usage, please refer to the product video below:

Video: Demonstration of NOPARDE Gobo Projector in various application scenarios.

4. Operation

The projector is designed to be used with a custom gobo lens. To get your customized logo projected, you need to purchase the projector and the logo lens together. After purchase, send your customized logo files to the provided email address. Supported file formats include AI, CDR, JPG, PNG, TIF, and PSD.

Diagram showing the process of combining a GOBO lens with a projector to create a projected logo, with instructions to send logo files to sales2@noparde.com.
Custom Logo Process

4.2. Projection Examples

The NOPARDE Gobo Projection Lamp can be used for various applications, including wall graphic decoration, restaurant copywriting, advertising logo drainage, hotel floor projection, ground logo projection, and store indicator projection.

Collage of various projection examples including wall graphics, restaurant text, advertising logos, and floor projections.
Diverse Projection Applications

5. Maintenance

5.1. Replacing the Lens

When replacing the lens, please pay attention to the following:

  • Always power off the projector before operating.
  • After the projector works for a long time, the temperature on the lens piece can be high. Handle with care to avoid burns.
  • When replacing, ensure the black side of the lens is facing outward. Fasten it with a fixing ring after replacement to prevent it from falling.

5.2. Steps for Lens Replacement

  1. Remove the front bezel.
  2. Remove the fixed ring and replace the light sheet.

5.3. General Care

The projector is made of durable aluminum alloy, designed to be unbreakable and resistant to damage. Regular cleaning of the exterior casing and lens (when cool and powered off) with a soft, dry cloth is recommended to maintain optimal performance.

Close-up of the projector's durable aluminum alloy casing, emphasizing its robust and unbreakable material.
Durable Aluminum Alloy Construction

6. Troubleshooting

  • If you encounter any problems with the product, please contact customer service immediately. Do not attempt to disassemble or repair the unit yourself, as this may void the warranty and cause further damage.
  • If the projection image quality is affected by rain percolation, ensure the waterproof fixing iron ring is properly tightened.

7. Specifications

Product Parameters
FeatureSpecification
Product NameGobo Projection Lamp
Model NumberGD/GJ/GS
Light TypeLED
Light BrandOSRAM
Input VoltageAC85-240V (Low Voltage does not support rotation)
Power Options25W, 35W, 50W, 80W, 100W
Luminous Flux2000-82000
Working Environment-40°C ~ 80°C
Waterproof LevelIP65 / IP67 (depending on model)
MaterialAluminum Alloy
Lens Diameter37.0mm
Lamp Size18.5*13.5*10cm
Imaging LensHD six slices of imaging
RotationRemote static rotation (for some models)
Color Temperature3000K-6000K
Life Expectancy50000H
CertificationCE, RoHS, PSE, KC
Table of product parameters including voltage, power, working environment, waterproof level, lens diameter, and warranty.
Detailed Product Parameters
Table showing GD series product parameters for black and silver models, including lamp beads, power supply, voltage, cooling method, body material, weight, total power, installation method, exterior color, and color temperature.
GD Series Product Parameters
Collage of various product certifications including Appearance Patent, CE, Certification Test, ROHS, PSE, and KC.
Product Certifications

8. Warranty & Support

The NOPARDE Gobo Projection Lamp comes with a Two Years Warranty. If you have any questions or require support, please contact customer service.

A detailed user manual is available for download here: User Manual (PDF)

9. User Tips

  • For custom logos, ensure you send your design files (AI, CDR, JPG, PNG, TIF, PSD) to the seller's email before production. The cost may vary depending on the number of colors in your logo.
  • Users have reported excellent image quality with clear and saturated colors.
  • For outdoor use, higher wattage models (e.g., 50W or 60W) can provide visible projections even in the afternoon or for greater distances (e.g., 6 meters high).
  • The projector is designed for easy installation and disassembly, making it convenient to set up and adjust.

10. Frequently Asked Questions (FAQ)

Q1: Are you a factory or trading company?
A: We are a real Manufacturer with strong R&D Capability, producing and selling by ourselves.
Q2: Can I custom my own logo?
A: Yes, please send your logo to us before production, and first confirm the design according to our samples.
Q3: Can you make a full color logo?
A: We can make any logo, including monochrome, bicolor, tricolor, and full color.
Q4: How soon can I get my sample order (with one or several pieces to test first)?
A: Usually it takes 3-5 working days to finish a sample order.
Q5: Do you offer guarantee for the products?
A: Yes, we offer 2 years warranty to our products.
Q6: In which format should I send the Logo?
A: Supported file formats include AI, CDR, JPG, PNG, TIF, and PSD.
Q7: Can we change the picture?
A: Yes, the projector uses interchangeable gobo lenses, allowing you to change the projected image by replacing the lens.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.