Introduction
Thank you for purchasing the WGNUUC Industrial Sconce Wall Light. This manual provides essential information for the safe and correct installation, operation, and maintenance of your new wall lamp. Please read these instructions thoroughly before installation and retain them for future reference.
Safety Instructions
- Always turn off the power at the main circuit breaker before beginning installation or performing any maintenance.
- Ensure all electrical connections are made in accordance with local codes, ordinances, and the National Electric Code (NEC). If you are unsure about wiring, consult a qualified electrician.
- Do not exceed the recommended wattage for the bulb.
- This fixture is designed for indoor use only and is not water-resistant. Avoid installation in damp or wet locations.
- Handle glass components with care to prevent breakage.
- Keep flammable materials away from the light fixture.
- Ensure the mounting surface can support the weight of the fixture.
Package Contents
Please check that all parts are present before beginning assembly:
- Lampshade
- Lamp Holder with pre-wired cable
- Adjustable Arm Segments (typically two)
- Wall Base / Mounting Plate
- Mounting Hardware (screws, wall plugs, washers)
- Retaining Ring for lampshade
- Ground Wire (if applicable)
Video: Overview of included components and basic assembly steps.
Specifications
| Attribute | Value |
|---|---|
| Style | Vintage |
| Installation Type | Wall Mounted |
| Material | Iron (Shade, Body), Aluminum, Zinc |
| Light Source | LED bulbs (not included) |
| Base Type | E27 |
| Voltage | 90 - 260 V, 220 V |
| Luminous Flux | <60 |
| Lighting Area | 3-5 square meters |
| Features | Long arm adjustable |
| Required Assembly | Yes |
| Water Resistance Level | No water resistant |
| Warranty | 1 year |
Dimensions
The wall lamp is available in various arm lengths. Please refer to the diagram below for specific measurements:
Image: Detailed dimensions for various arm lengths and configurations (e.g., A1-15+15 CM, B1-10+10 CM, D1-10+10 CM, C1-10+10 CM).
Setup and Installation
Follow these steps to install your wall lamp. It is recommended to have a second person assist during installation.
- Mark Position: Mark the wall position using the mounting plate as a template. Then, drill the holes in the wall (refer to Fig. 1 in the diagram below).
- Insert Wall Plugs: Insert the plastic wall plugs into the drilled holes (refer to Fig. 2).
- Secure Mounting Plate: Align the mounting plate with the wall plugs, add the washers, and tighten the screws (refer to Fig. 3).
- Assemble Lamp Arms: Connect the lamp arms in sequence with the lamp holder, and route the wire through the small angle joint (refer to Fig. 4).
- Fix Arm and Base: Fix the lamp arm and wall base. Connect the wires with wire connectors, then secure the base to the wall (refer to Fig. 5).
- Fasten Lampshade: Fasten the lampshade to the lamp holder with the retaining ring (refer to Fig. 6).
- Install Bulb: Install a suitable E27 bulb (not included) into the E27 socket.
Note:
- If no ground wire is reserved in the wall, the fixture can be installed without connecting a ground wire.
Image: Step-by-step installation guide with figures 1 through 6.
Operating Instructions
Once installed, operate the wall lamp as follows:
- Power On/Off: Use the wall switch connected to the fixture to turn the light on or off.
- Adjusting the Arm: The long arm features adjustable joints, allowing you to position the light as needed. Gently loosen the wing nuts or adjustment screws at the joints, reposition the arm, and then tighten them securely to hold the desired angle.
Maintenance
- Cleaning: To clean the fixture, ensure the power is off. Wipe with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the finish.
- Bulb Replacement: Ensure the power is off and the bulb has cooled completely. Unscrew the old E27 bulb and screw in a new E27 LED bulb (max wattage as per local regulations, typically 60W equivalent for LED).
Troubleshooting
- Light does not turn on:
- Check if the power switch is in the ON position.
- Verify that the circuit breaker is not tripped.
- Ensure the bulb is correctly installed and not faulty. Try a new bulb.
- Check all wiring connections for looseness or incorrect installation.
- Light flickers:
- Ensure the bulb is screwed in tightly.
- Check for loose wiring connections.
- The bulb may be faulty; try replacing it.
User Tips
- The lamp's long arm is designed for adjustability. While it offers significant flexibility in positioning, it may not support full 360-degree rotation at every joint. Adjust gently to find your desired angle.
- Consider using a vintage-style LED bulb to complement the industrial/retro aesthetic of the lamp.
- For optimal lighting in larger rooms, consider installing multiple units or pairing with other light sources.
Warranty and Support
This WGNUUC Industrial Sconce Wall Light comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.
For technical support, warranty claims, or any questions not covered in this manual, please contact the seller or manufacturer directly through your purchase platform.
A PDF version of the user manual is available for download: Download User Manual (PDF)