ZSDTRP FCR Carburetor

Contents

ZSDTRP FCR Keihin Carburetor Instruction Manual

Models: FCR28, FCR31, FCR33, FCR35, FCR37, FCR39, FCR41

1. Safety Information

WARNING:

  • Gasoline is extremely flammable. Do not smoke. Work in a well-ventilated area away from open flames or sparks.
  • Wear protective gear: Safety glasses and gloves are recommended.
  • Engine parts get hot: Allow the engine to cool completely before beginning installation to prevent burns.
  • Proper installation is critical for safety. Improper installation or adjustment can lead to poor performance, engine damage, or serious injury. If you are not confident in your mechanical skills, have a professional mechanic perform the installation.

2. Tools Required

Before beginning installation, ensure you have the following tools:

  • Set of standard and metric screwdrivers
  • Set of metric sockets and wrenches
  • Carburetor cleaner
  • Clean, lint-free rags
  • Small container for capturing fuel

3. Setup and Installation

Part 1: Preparation and Bench Settings

Before installing the carburetor on the engine, you must set the baseline adjustments.

  1. Inspect the Carburetor: Ensure the carburetor body is clean and free of debris. Check that all inlet and outlet ports are clear.
  2. Set Initial Idle Mixture: Gently turn the idle mixture screw (often located on the bottom or side of the carburetor) clockwise until it lightly seats. Do not overtighten, as this can damage the delicate tip. Now, turn it counter-clockwise to the initial setting: Standard Starting Point: 1-1/2 to 2 turns out.
  3. Set Initial Idle Speed: Turn the idle speed screw (which contacts the throttle linkage) clockwise until it just touches the throttle stop. Then, turn it an additional 1/2 turn clockwise to slightly open the throttle plate. This ensures the engine will have enough air to start.
  4. Check the Float: Tilt the carburetor so the float arm rests against the needle valve (but does not compress the spring in the needle). Measure the distance from the float bowl mating surface to the bottom of the float. This dimension varies by model, but a common range is 0.4" to 0.7" (10mm to 18mm). Bend the float tab carefully to adjust if necessary.

Part 2: Carburetor Installation

  1. Install the Manifold and Insulator: If removed, install the intake manifold and the insulator block onto the engine cylinder head. Ensure the O-ring side of the insulator block faces the manifold. Use new gaskets.
  2. Attach Throttle Cables: Install the correct throttle cable bracket onto the carburetor. Apply a drop of thread-locker (Loctite® 243) to the bracket screws. Connect the pull (opening) throttle cable barrel fitting into the throttle linkage. Seat the cable housing into the bracket. Connect the push (closing) throttle cable in the same manner. This cable usually has a spring around it.
  3. Mount the Carburetor: Loosen the clamps on the intake boot. Carefully slide the carburetor outlet (engine side) into the rubber intake boot. Ensure it is fully seated and sits straight. Tighten the clamp securely with a screwdriver.
  4. Connect Hoses: Connect the fuel hose from the petcock (fuel valve) to the carburetor inlet. Secure it with a clamp. Route the float bowl drain tube(s) and overflow tube(s) down toward the ground, away from hot engine parts or the exhaust. If your carburetor is liquid-cooled, connect the coolant hoses as noted in your service manual.
  5. Install Air Cleaner: Attach the air cleaner assembly to the carburetor intake bell. Ensure the clamp is tight to prevent unfiltered air from being drawn in, which can cause severe engine wear.
Carburetor installed on a motorcycle engine
Example of carburetor installed on a motorcycle engine.

4. Operating and Fine-Tuning

After installation, the carburetor may require fine-tuning to achieve optimal performance for your specific engine, altitude, and climate conditions. The initial bench settings provide a starting point, but further adjustments may be necessary.

  • Idle Mixture Adjustment: Adjust the idle mixture screw in small increments (e.g., 1/8 turn) to achieve the highest idle RPM, then turn it slightly richer (counter-clockwise) until the RPM just begins to drop or the engine runs smoothly.
  • Idle Speed Adjustment: Use the idle speed screw to set the desired engine idle RPM.
  • Float Level: Incorrect float level can lead to fuel starvation or overflow. If you experience these issues, re-check and adjust the float level as described in the setup section.
  • Jetting: The carburetor comes with a set of main and pilot jets. Optimal jetting depends on your engine's modifications, exhaust system, air filter, and environmental factors. Consult a professional mechanic or a detailed tuning guide for your specific motorcycle model if you are unsure about jetting changes.

5. Maintenance

Regular maintenance of your carburetor is essential for consistent performance and longevity.

  • Cleaning: Periodically clean the carburetor using a specialized carburetor cleaner. Ensure all passages and jets are clear of debris and varnish.
  • Air Filter: Maintain a clean air filter to prevent contaminants from entering the carburetor and engine.
  • Fuel Quality: Use high-quality, fresh fuel. Stale or contaminated fuel can lead to deposits and performance issues.
  • Hose Inspection: Regularly inspect fuel and vacuum hoses for cracks, leaks, or deterioration. Replace as needed.
  • Cable Lubrication: Lubricate throttle cables periodically to ensure smooth operation.

6. Troubleshooting Common Issues

If you encounter problems after installation or during operation, consider the following:

  • Engine Not Starting:
    - Check fuel supply to the carburetor.
    - Verify spark.
    - Ensure idle mixture and speed settings are correct.
    - Check for proper float level.
  • Poor Idle/Stalling:
    - Adjust idle mixture and speed.
    - Inspect for vacuum leaks around the intake manifold or hoses.
    - Clean pilot jet.
  • Poor Acceleration/Hesitation:
    - Check main jet size for your application.
    - Ensure accelerator pump (if equipped) is functioning correctly.
    - Verify throttle cable tension and smooth operation.
  • Fuel Leaks:
    - Inspect float bowl gasket and drain screw.
    - Check float level (too high can cause overflow).
    - Ensure fuel hose connections are secure.
  • Over-rich/Over-lean Condition:
    - Adjust jetting (main jet, pilot jet, needle position) according to engine requirements and environmental factors.

7. Specifications

FeatureSpecification
Brand NameZSDTRP
Item TypeCarburetor
MaterialAluminum Alloy
External Testing CertificationISO9000
Item Weight1.15 kg
Item Height17.5 cm
Item Width11.5 cm
Item Diameter (General)3.9 cm
OriginMainland China

Venturi Sizes and Engine Displacement Compatibility

Venturi SizeEngine Displacement (Approx.)
28mm110cc to 150cc
31mm125cc to 250cc
33mm150cc to 250cc
35mm200cc to 350cc
37mm250cc to 450cc
39mm300cc to 500cc
41mm300cc to 650cc
Carburetor dimension diagram
Diagram illustrating carburetor dimensions (A, B1, B2, C, D).

Detailed Dimensions (mm)

ModelAB1(I.D)B2(O.D)CD
FCR2855mm28mm35mm98mm155mm
FCR3355mm33mm40mm115mm155mm
FCR3555mm35mm40mm115mm155mm
FCR3772mm37mm48mm115mm175mm
FCR3972mm39mm48mm115mm175mm
FCR4172mm41mm48mm115mm175mm
Table of carburetor dimensions
Table of detailed dimensions for various FCR carburetor models.

Jetting Information

ModelOriginal JettingSpare JettingOthers
FCR28K125K48K115K43Hand Damper24 mm interface
FCR33K105K48K130K46Hand Damper
FCR35K115K48K135K47Hand DamperAutomatic Damper
FCR37K170K48K42, K45
FCR39K170K48K48, K50
FCR41K170K48K52, K55
K58, K60
Table of original and spare jetting for FCR carburetors
Table showing original and spare jetting specifications for various FCR carburetor models.

For a comprehensive user manual with additional details, please refer to the official PDF document: User Manual (PDF)

8. User Tips

  • Pre-Jetted for Basic Operation: The carburetor may come pre-jetted for basic operation, allowing the engine to start immediately. However, fine-tuning is almost always required for optimal performance.
  • Jet Kit Included: Many users report that the carburetor is supplied with a helpful selection of main and pilot jets, which can assist in tuning.
  • Professional Installation Recommended: Replacing and tuning a carburetor requires experience and technical knowledge. Engine conditions, altitude, climate, and even oil type can affect performance. If you are not confident in your mechanical skills, seek professional assistance for installation and fine-tuning.
  • Needle Verification: Some users suggest verifying the carburetor needle's specifications against original parts for your specific bike, as unmarked needles may require replacement for proper function.
  • Adaptation May Be Necessary: Depending on your motorcycle model, some adaptation might be required for a perfect fit and optimal performance.
  • Cold Start Functionality: The carburetor includes a cold start mechanism, but it may require careful adjustment to work effectively.

9. Frequently Asked Questions (FAQ)

Q: What is included in the carburetor kit?
A: The kit typically includes the carburetor itself, along with a selection of main and pilot jets, and sometimes an adapter for the cylinder head side and an additional fuel filter.
Q: Will this FCR39 fit an LC4 640?
A: A 39mm carburetor might be suitable for an LC4 640, potentially offering better low-end torque. However, specific fitment and tuning will be required.
Q: Is it possible to have a remote choke?
A: This carburetor typically features a manual choke. Adapting it for a remote choke would likely require custom modifications.
Q: Is there a hot start button?
A: Please check the specific model you receive, as hot start mechanisms can vary or may need to be added/adapted.
Q: What is the length of the needle? Does it affect performance?
A: The needle length and taper are crucial for fuel delivery across the throttle range. If the needle is not correctly matched to your engine, it can lead to poor performance. Some users suggest replacing the needle with an original specification part if the included one is unmarked or causes issues.
Q: Can two of these carburetors be connected for a twin-cylinder engine (e.g., XT 600E)?
A: While technically possible to adapt two carburetors for a twin-cylinder engine, this would be a complex custom project requiring significant fabrication and expert tuning. The price listed is typically for a single carburetor.

10. Warranty and Support

For any issues or questions regarding your ZSDTRP FCR Keihin Carburetor, please contact the seller or manufacturer directly. Ensure you retain your purchase records for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.