diymore Voltmeter Ammeter

Contents

0.28" Dual LED Display Mini Digital Voltmeter Ammeter

User Instruction Manual

1. Introduction

Thank you for choosing the diymore 0.28" Dual LED Display Mini Digital Voltmeter Ammeter. This compact and versatile device is designed to accurately measure DC voltage from 0 to 100V and DC current from 0 to 10A, displaying readings on a clear dual-color LED screen. This manual provides essential information for safe and effective use of your device.

Front and back view of the Voltmeter Ammeter module

Figure 1: Front (top) and Back (bottom) view of the Voltmeter Ammeter module.

2. Package Contents

  • 1 x 0.28" Dual LED Display Mini Digital Voltmeter Ammeter
  • 1 x 3-pin wire harness (thin wires: Red, Black, Yellow)
  • 1 x 2-pin wire harness (thick wires: Red, Black)
Package contents including meter, anti-static bag, and wire harnesses

Figure 2: Voltmeter Ammeter module with included wire harnesses.

3. Setup and Wiring

Careful wiring is essential for proper operation and to prevent damage to the device or your circuit. Refer to the diagrams and instructions below.

3.1. Mounting

The module is designed for panel mounting. The dimensions are 48mm (width) x 29mm (height) x 26mm (depth). Ensure you cut an appropriate opening in your panel for a snug fit.

3.2. Wiring Connections

The device uses two separate wire harnesses for power/voltage measurement and current measurement.

Voltmeter Ammeter with connected wire harnesses

Figure 3: Voltmeter Ammeter with wire harnesses connected.

3.2.1. Power Supply and Voltage Measurement (Thin 3-pin connector)

  • Thin Red Wire: Connect to the positive (+) terminal of your DC power supply (4V to 30V DC). This powers the meter itself.
  • Thin Black Wire: Connect to the negative (-) terminal of your DC power supply. This is also the common ground for voltage measurement.
  • Thin Yellow Wire: Connect to the positive (+) point of the circuit where you want to measure voltage (0V to 100V DC).

CAUTION: Do NOT exceed 30V DC on the thin red wire, as this will damage the meter. If the voltage you are measuring (via the yellow wire) is higher than 30V, the meter's power supply (thin red/black) must be separate from the measured circuit's power supply, but they must share a common ground (thin black wire).

3.2.2. Current Measurement (Thick 2-pin connector)

The thick red and black wires are for current measurement and act as a shunt. They must be connected in series with the load you wish to measure.

  • Thick Red Wire: Connect to the positive (+) output of your power source.
  • Thick Black Wire: Connect to the positive (+) input of your load.

This configuration places the ammeter in series with the positive line of your circuit. Ensure the current does not exceed 10A.

IMPORTANT: For accurate readings and to prevent damage, ensure all connections are secure and correct before applying power. The meter's power supply (thin red/black) and the circuit being measured (thick red/black, thin yellow) must share a common ground for proper operation.

4. Operating Instructions

  1. After completing all wiring connections as described in Section 3, apply power to the meter (DC 4-30V).
  2. The dual LED display will illuminate. The upper (red) display shows the voltage in Volts (V), and the lower (blue) display shows the current in Amperes (A).
  3. The meter will continuously display the measured voltage and current.

Note: If the voltage being measured is below 10V, the voltage display will show two decimal places (e.g., 0.00V). For voltages 10V and above, it will show one decimal place (e.g., 12.3V).

5. Maintenance

  • Cleaning: To clean the display and casing, use a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Storage: When not in use, store the device in a dry, dust-free environment, away from direct sunlight and extreme temperatures.
  • Service: This device contains no user-serviceable parts. Do not attempt to open or repair the unit yourself, as this will void any potential warranty.

6. Troubleshooting

Problem Possible Cause Solution
No display / Meter not turning on
  • No power to the meter (thin red/black wires).
  • Power supply voltage is outside 4-30V DC range.
  • Incorrect wiring.
  • Check power connections to the thin red and black wires.
  • Verify power supply voltage is within 4-30V DC.
  • Review wiring according to Section 3.
Incorrect voltage reading
  • Thin yellow wire not connected or connected incorrectly.
  • Loose connection.
  • Meter requires calibration.
  • Ensure thin yellow wire is connected to the correct voltage measurement point.
  • Check for secure connections.
  • Refer to User Tips for calibration information.
Incorrect current reading
  • Thick red/black wires not connected in series with the load.
  • Loose connection.
  • Current exceeds 10A.
  • Meter requires calibration.
  • Verify thick red/black wires are correctly wired in series with the load.
  • Check for secure connections.
  • Ensure current does not exceed 10A.
  • Refer to User Tips for calibration information.
Meter burned out / Damaged
  • Input voltage to meter (thin red wire) exceeded 30V DC.
  • Current through shunt (thick wires) exceeded 10A.
  • Incorrect wiring or short circuit.
  • Ensure power supply to meter is within 4-30V DC.
  • Do not exceed 10A current measurement.
  • Double-check all wiring before applying power.

7. Specifications

Working Voltage (Meter)DC 4 - 30V (Maximum input voltage cannot exceed 30V)
Working Current (Meter)≤20mA
Voltage Measuring RangeDC 0 - 100V
Current Measuring RangeDC 0 - 10A
Voltage Resolution0.1V (Displays 0.00V when voltage is under 10V)
Current Resolution0.01A
Measurement Accuracy1% (± 1 digit)
Display Type0.28" Digital Tube, Dual LED (Red for Voltage, Blue for Current)
Refresh RateApproximately 300mS / times
Dimensions48mm x 29mm x 26mm
Operating Temperature-10°C to 65°C
CertificationCE

8. User Tips

  • Calibration: If you notice slight inaccuracies in voltage or current readings, there are small trimpots (potentiometers) on the back of the PCB (see Figure 1, bottom) that can be adjusted with a small screwdriver for calibration. Adjust carefully while comparing readings with a known accurate multimeter.
  • Wire Gauge: For applications consistently drawing close to the 10A limit, consider using slightly thicker gauge wires for the current measurement circuit if the included wires appear too thin for your specific setup.
  • Automotive Use: When installing in vehicles or motorcycles, ensure the power supply to the meter is stable and protected from voltage spikes. Vibration and moisture can also affect longevity.
  • Common Ground: Always ensure a common ground connection between the meter's power supply and the circuit being measured for stable and accurate readings.
Close-up of the back PCB showing trimpots

Figure 4: Close-up of the back PCB, showing adjustment trimpots (small square components with a screw slot).

9. Warranty and Support

For warranty information and technical support, please contact your original retailer or the point of purchase. Please have your purchase details ready when contacting support.

An additional user manual in PDF format may be available for download from the seller's product page or directly at: User Manual (PDF).

© 2024 diymore. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.