1. Introduction
This manual provides essential instructions for the safe and efficient operation of your ZJIVNV S-2000 2000W Switching Power Supply. This device is designed to provide adjustable DC voltage and current outputs, suitable for a wide range of applications. Please read this manual thoroughly before installation and use.
2. Safety Instructions
- Electrical Hazard: Always ensure the power supply is disconnected from the AC mains before performing any installation, wiring, or maintenance.
- Proper Grounding: The earth wire must be firmly grounded to ensure safety and reduce interference. The cross-sectional surface of the grounded copper wire should exceed 0.75mm.
- Voltage Selection: Before connecting to AC power, ensure the input voltage switch (if present) is set correctly to either 115V or 230V to prevent damage.
- Environmental Conditions: Avoid operating the power supply in environments with extreme temperatures, high humidity (ensure it's absolutely dry), excessive dust, or acid-base pollution.
- Ventilation: Ensure the SMPS work environment has unblocked airflow to prevent overheating and shorten its lifespan.
- Installation: Remove all plastic packing materials before installation. Do not use screws that are too long, as they may contact internal circuit boards or components.
3. Product Overview
The ZJIVNV S-2000 is a high-power switching power supply featuring adjustable voltage and current outputs. It includes a digital display for real-time voltage and current monitoring.
3.1. Key Features
- Adjustable Voltage Output: Ranges from 0-12V up to 0-600V (depending on model variant).
- Adjustable Current Output: Up to 100A.
- Digital Voltage and Current Display.
- Built-in Cooling Fan.
- Overload and Short Circuit Protection.
3.2. Components and Indicators
Refer to the image below for a visual guide to the power supply's front panel and overall design.

Image 1: Front view of the ZJIVNV S-2000 Power Supply. Shows the digital display for Voltage (V) and Amperage (A), voltage and current adjustment knobs, ON/OFF switch, and 'WORKING' (green) and 'FAULT' (red) indicator lights.
- Voltage & Current Display: Digital readout for output voltage and current.
- VOLT (Voltage Adjustment): Knob to adjust the output voltage.
- CURR (Current Adjustment): Knob to adjust the output current limit.
- ON/OFF Switch: Main power toggle.
- WORKING Indicator (Green): Illuminates when the power supply is operating normally.
- FAULT Indicator (Red): Illuminates if an error or fault condition occurs.
- Output Terminals (+V, -V): Red terminal for positive output, Black terminal for negative output.
- Cooling Fan: Located at the rear/side for heat dissipation.
4. Setup
4.1. Pre-Power On Checks
- Input/Output Line Verification: Ensure the AC input lines (Live 'L', Neutral 'N', Earth '⏚') and DC output lines (Positive '+V', Negative '-V') are correctly connected.
- Wire Cross-Section: Verify that the cross-section of the input electric wire is sufficient to prevent excessive voltage drop (AC voltage drop not exceeding 5%, DC voltage drop not exceeding 0.5%).
- Connections: Check that all screw terminals and internal switching device connections are secure and have good contact.
- Insulation: Confirm that the insulation resistance between the shell and input/output terminals, and the withstand voltage, meet the required standards.
- Grounding: Ensure the earth wire is firmly grounded for safety and to minimize interference.
4.2. AC Input Voltage Selection
If your model has a voltage selector switch, set it to match your local AC mains voltage (115V or 230V) before connecting the power cord. Incorrect selection can damage the unit.
4.3. Output Connections
Connect your load to the output terminals. The red terminal is for positive (+V) and the black terminal is for negative (-V). Ensure correct polarity to avoid damage to your load device.

Image 2: Rear view of the power supply, showing the cooling fan, AC input socket, and DC output terminals.
4.4. Multi-Output Considerations
If your power supply has multiple DC outputs (main and secondary), the main output typically has superior characteristics. If only secondary outputs are used, a dummy load of at least 30% of the rated power output should be added to the main output.
5. Operating Instructions
- Connect Power: Plug the AC power cord into a suitable mains outlet.
- Power On: Flip the ON/OFF switch to the 'ON' position. The digital display should illuminate, and the 'WORKING' indicator (green) should light up.
- Adjust Voltage: Turn the 'VOLT' knob clockwise to increase the output voltage and counter-clockwise to decrease it. Observe the digital display for the current voltage setting.
- Adjust Current: Turn the 'CURR' knob clockwise to increase the output current limit and counter-clockwise to decrease it. This sets the maximum current the power supply will deliver.
- Monitor Output: The digital display continuously shows the actual output voltage and current being delivered to the load.
- Power Off: When finished, flip the ON/OFF switch to the 'OFF' position and disconnect the AC power cord.
5.1. Operation Demonstration
Watch this video for a visual guide on powering on and adjusting the voltage of the power supply.
Video 1: Product demonstration showing the ZJIVNV S-2000 power supply being turned on and its voltage output adjusted from a low value up to 600V.
6. Maintenance
- Cleaning: Keep the power supply clean and free from dust. Use a soft, dry cloth for cleaning. Do not use liquid cleaners.
- Ventilation: Regularly check that the cooling fan and ventilation holes are not obstructed. Clean any dust accumulation from the fan blades and vents.
- Environmental Control: Operate the unit within its specified temperature and humidity ranges. Avoid rapid temperature changes.
- Power Stability: If your AC mains voltage fluctuates dramatically, consider using an external power stabilizer or over/under voltage protector to protect the power supply and connected equipment.
- AC Filter: When supplying power to large electrical equipment, consider installing an AC filter to protect the power supply.
- Frequent On/Off: Avoid frequently switching the input voltage on and off, as this can affect the lifespan of the unit.
7. Troubleshooting
- No Output/No Display: Check the AC power connection and the ON/OFF switch. Ensure the input voltage selector (if present) is correctly set.
- FAULT Indicator On: This indicates an internal error, overload, or short circuit. Disconnect the load, power off the unit, wait a few minutes, and then power it back on. If the fault persists, contact support.
- Output Voltage/Current Unstable: Check all wiring connections for looseness. Ensure the load is within the power supply's specifications. Verify the stability of your AC input.
- Overheating: Ensure adequate ventilation around the unit. Check if the cooling fan is operating correctly and if its vents are clear of obstructions. Reduce the load if operating in high ambient temperatures.
- Unit Does Not Start in Cold Conditions: The power supply may not start or output normally if the environment temperature is below -10°C. Allow the unit to warm up in a suitable environment.
8. Specifications
| Feature | Specification |
|---|---|
| Type | Power Supply (Switching) |
| Model Number | S-2000 |
| Rated Capacity | 40-1000VA |
| Output Power | 2000W (Max) |
| Output Voltage Range | Adjustable from 0-12V up to 0-600V (model dependent) |
| Output Current Range | Adjustable from 0-100A (model dependent) |
| Output Frequency | 50/60 HZ |
| Output Type | SINGLE |
| Product Size | 350*145*120mm |
| Certificates | CE, RoHS, FCC |
| Warranty | 2 years |
9. User Tips
- Display Readout: The front panel digital display shows both the output voltage (V) and current (A) simultaneously, allowing for easy monitoring of your load.
- Load Compatibility: This is a switching power supply (SMPS), which is generally efficient and compact. Ensure your application is compatible with SMPS characteristics.
- Voltage Adjustment Range: Be mindful of the specific voltage range of your purchased model (e.g., 0-12V, 0-24V, up to 0-600V) to match your application needs.
10. Warranty and Support
This ZJIVNV product comes with a 2-year warranty from the date of purchase, covering manufacturing defects. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer's customer service.