diymore 25A 3S/4S/5S 18650 Li-ion Lithium Battery Protection Board Module

Contents

User Manual: diymore 25A 3S/4S/5S 18650 Li-ion Lithium Battery Protection Board Module

Model: 25A 3S/4S/5S 18650 Li-ion Lithium Battery Protection Board Module

1. Introduction

This document provides instructions for the diymore 25A 3S/4S/5S 18650 Li-ion Lithium Battery Protection Board Module (BMS PCM). This module is designed to protect Li-Polymer and LiMnO battery cells (3.6V/3.7V nominal) during charging and discharging cycles, ensuring safety and extending battery life. It features protection against overcharge, over-discharge, overcurrent, and short circuits.

Angled top view of the diymore 25A BMS board
Figure 1: Angled top view of the BMS board, showing components.

2. Specifications

FeatureSpecification
ApplicationComputer (General electronic projects)
TypeVoltage Regulator / Battery Protection Module
Brand Namediymore
ConditionNew
PackageSMD
Single Cell Overcharge Protect Voltage4.23 - 4.28V
Single Cell Overcharge Recover Voltage4.08 - 4.18V
Overcharge Protect Delay0.5 - 1.5S
Single Cell Over-discharge Protect Voltage2.72 - 2.88V
Single Cell Over-discharge Recover Voltage2.9 - 3.1V
Overcharge Protect Current60A
Over-discharge Protect Current60A
Over-discharge Protect Delay0.5 - 1.5S
Temperature ProtectionYES
Disconnect ProtectionYES
Shortage ProtectionYES
Shortage Delay100 - 600μS
Shortage Protect RecoverYES
Charging Current25A
Discharging Current25A
Charging Voltage (3S)12.6V
Charging Voltage (4S)16.8V
Charging Voltage (5S)21V

3. Setup and Wiring

Careful wiring is essential for the correct and safe operation of the BMS module. Refer to the diagrams below for connecting your battery cells, charger, and load.

3.1 General Wiring Principles

  • Connect the battery cells in series as indicated by the 'B-', 'B1', 'B2', 'B3', 'B4', 'B+' terminals.
  • The 'P-' terminal is the negative output for both charging and discharging.
  • The 'P+' terminal is the positive output for both charging and discharging.
  • Ensure all connections are secure and correctly polarized.
  • The board itself has clear markings for each connection point.

3.2 Wiring Diagrams

The following diagrams illustrate the connections for 3S, 4S, and 5S battery configurations. Please select the diagram corresponding to your specific BMS board and battery pack.

Wiring diagram for a 3S battery configuration with the BMS board, showing connections for battery cells, charger, and load.
Figure 2: 3S BMS Wiring Diagram. Connect three battery cells in series. The charger and load connect to P- and P+.
Wiring diagram for a 4S battery configuration with the BMS board, showing connections for battery cells, charger, and load.
Figure 3: 4S BMS Wiring Diagram. Connect four battery cells in series. The charger and load connect to P- and P+.
Wiring diagram for a 5S battery configuration with the BMS board, showing connections for battery cells, charger, and load.
Figure 4: 5S BMS Wiring Diagram. Connect five battery cells in series. The charger and load connect to P- and P+.

3.3 NTC Thermistor Connection

The board includes NTC contacts on the reverse side. These are for connecting an external NTC thermistor (temperature sensor) to provide temperature protection for the battery pack during charging and discharging. This helps prevent overheating.

Bottom view of the BMS board, highlighting the NTC pads for temperature sensor connection.
Figure 5: Bottom view of the BMS board, showing NTC pads.

4. Operating Instructions

Once correctly wired, the BMS module will automatically manage the battery pack's safety features.

4.1 Charging

  • Connect your charger to the P- and P+ terminals.
  • The BMS will prevent overcharging by cutting off the charge current if any cell voltage exceeds the overcharge protection voltage (4.23 - 4.28V).
  • Ensure your charger provides the correct voltage for your battery configuration (e.g., 12.6V for 3S, 16.8V for 4S, 21V for 5S). Using a lower voltage for charging (e.g., 19V for a 5S pack) will result in an undercharged battery.

4.2 Discharging

  • Connect your load to the P- and P+ terminals.
  • The BMS will prevent over-discharging by cutting off the discharge current if any cell voltage drops below the over-discharge protection voltage (2.72 - 2.88V).
  • Overcurrent protection will activate if the discharge current exceeds 60A.
  • Short-circuit protection will activate if a short circuit is detected, with a delay of 100-600μS.

5. Maintenance

  • Keep the module dry and clean. Avoid exposure to moisture or corrosive substances.
  • Avoid physical impact or excessive bending of the board.
  • Regularly inspect wiring for loose connections or damage.
  • Ensure adequate ventilation if the module is enclosed, especially during high current operation.

6. Troubleshooting

  • Low Output Voltage (e.g., 7V for 5S): This could indicate a problem with one or more battery cells, or a defective BMS board. Check individual cell voltages. If cells are healthy, the BMS might be faulty.
  • Frequent Protection Trips (e.g., in power tools): For high-current applications like screwdrivers, a 25A continuous discharge current might be insufficient, leading to overcurrent protection activation. Consider a BMS with a higher current rating (e.g., 40A or more) for such uses.
  • Battery Not Fully Charging: Ensure your charger provides the correct voltage for your battery configuration (e.g., 21V for a 5S pack). A lower voltage will not fully charge the battery.
  • No Charge Indicator: This BMS module is a protection board, not a smart charger. It does not have built-in charge indicators. It primarily cuts off current when protection limits are reached.
  • Difficulty Distinguishing 3S/4S/5S Boards: Refer to the markings on the board itself and the number of balance wire connection points. The wiring diagrams also clearly show the number of cells.

7. User Tips

  • This BMS board is well-suited for replacing NiMH cells in power tools with lithium-ion batteries, provided the current requirements are met.
  • Always double-check your wiring against the provided diagrams and the markings on the board to prevent damage.
  • For applications requiring high burst currents, such as cordless drills, consider using a BMS with a higher continuous discharge current rating (e.g., 40A) to avoid premature cut-offs.
  • Utilize the NTC thermistor connection for enhanced temperature monitoring and protection of your battery pack, especially during charging.

8. Warranty and Support

For warranty information, technical support, or further inquiries, please contact the seller directly. A detailed user manual in PDF format may also be available for download from the seller's product page or via this link: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.