1. Introduction
The TOMZN TOVPD1-60 is an automatic recovery over-voltage and under-voltage protective device designed to safeguard electrical equipment and personnel from unstable power conditions. It features a modular design and incorporates high-quality electronic components for reliable performance. When the voltage exceeds or falls below predefined limits, the device automatically cuts off the power supply. It will then automatically restore power after a 1-minute delay once the voltage returns to normal operating range.
2. Safety Information
Warning: To avoid danger of suffocation, keep this bag away from babies and children. Do not use this bag in cribs, beds, carriages, or play pens. This bag is not a toy.
General Safety Precautions
- Installation and operation must be performed by a qualified electrical professional.
- Do not place the device near flammable materials.
- Ensure adequate ventilation around the device during operation.
- Disconnect the device from power and store it properly when not in use for extended periods.
3. Product Overview
The TOMZN TOVPD1-60 is a compact, DIN rail-mountable device. It features clear input and output terminals, along with three LED indicators for power and protection status.


Dimensions

Key Features

4. Specifications
| Feature | Specification |
|---|---|
| Rated AC Voltage | 230V±10% 50/60Hz |
| Passing Max Current | 40A |
| Max. Loading Power | 8.8kVA |
| Over-voltage action cut-off value | >270VAC±5V |
| Normal-voltage value | 175-270VAC |
| Under-voltage action cut-off value | <170VAC±5V |
| Over/Under voltage cut off time | < 1s |
| Electricity transmitting delay after cut off | <60s |
| Self power consumption | <2W |
| Electric machinery life | 100,000 times |
| Dimension | 67mm (L) * 36mm (W) * 82mm (H) |
| Installation | 35mm Din rail |
| LED Lamps | Power, Under voltage indicator, Over voltage indicator |
| Wiring | Top input, bottom output |
| EU LVD Voltage | High voltage: Above 50Vac or 75Vdc |
| Certification | CE |
5. Setup and Installation
Important: All installation must be performed by a qualified electrical professional. Ensure power is disconnected before beginning installation.
Installation Steps
- Mount the device on a standard 35mm DIN rail.
- Connect the equipment according to the wiring diagram specifications. The device has top input (N, L) and bottom output (N, L).
- After connecting, wait approximately 1 minute for the device to initialize. The red light will turn off, indicating the product is ready for operation.

6. Operating Instructions
The device operates automatically to protect against voltage fluctuations.
LED Indicators
- Power Indicator (Green LED): Illuminates when the power supply is normal.
- Under Volt Protection Indicator (Red LED): Illuminates when under-voltage protection is triggered.
- Over Volt Protection Indicator (Red LED): Illuminates when over-voltage protection is triggered.
When the voltage is too high or too low, the device will automatically disconnect the load. Once the voltage returns to the normal range (175-270VAC), the device will automatically reconnect the power after a delay of less than 60 seconds.

7. Maintenance
The TOMZN TOVPD1-60 is designed for long-term, maintenance-free operation. To ensure optimal performance and longevity:
- Periodically check the device and its connections for any signs of damage, wear, or loose wiring.
- Ensure the area around the device remains clear and unobstructed to allow for adequate ventilation.
- Clean the exterior of the device with a dry, soft cloth if necessary. Do not use liquids, solvents, or abrasive cleaners.
8. Troubleshooting
Device Not Powering On / No Output
- Check the input voltage to ensure it is within the normal operating range (175-270VAC).
- Verify all wiring connections are secure and correct according to the wiring diagram.
- Ensure the initial 1-minute delay after connecting power has passed.
Protection Triggered Frequently
- Monitor your power supply for frequent over-voltage (>270VAC) or under-voltage (<170VAC) events. This may indicate an issue with your electrical supply.
- Ensure the device's current rating (40A) is sufficient for your connected load. Overloading can cause unexpected behavior.
9. User Tips
- Initial Connection Delay: When first connecting the product, allow approximately 1 minute for it to initialize. The red light will turn off when it's ready to operate.
- LED Brightness: Some users have noted the LEDs can be quite bright. Consider placement if this is a concern in dark environments.
- Load Matching: Ensure the device's amperage rating (e.g., 40A) is appropriate for your circuit's main breaker to prevent issues.
10. Applicable Regulations and Harmonized Standards
This device complies with the following regulations and harmonized standards:
- Low Voltage Directive 2014/35/EU
- Electromagnetic Compatibility Directive 2014/30/EU
- Restriction of the Use of Certain Hazardous Substances (RoHS) Directive 2011/65/EU
11. Warranty and Support
For warranty information and technical support, please refer to the official TOMZN website or contact your authorized dealer. Keep your purchase receipt for warranty claims.