E-SIMPO E17-E12

Contents

E-SIMPO E17 to E12 Lamp Holder Converter Instruction Manual

1. Introduction

Thank you for choosing the E-SIMPO E17 to E12 Lamp Holder Converter. This adapter is designed to convert an E17 screw socket into an E12 small screw lamp socket, allowing you to use E12 base bulbs in fixtures designed for E17 bases. This manual provides essential information for safe installation, operation, maintenance, and troubleshooting.

Six E17 to E12 lamp holder converters
Figure 1: E-SIMPO E17 to E12 Lamp Holder Converters (6-pack)

This image displays six E17 to E12 lamp holder converters. Three are shown with the E17 male base facing upwards, and three are shown with the E12 female socket facing upwards, illustrating both ends of the adapter.

2. Safety Warnings

Please read and understand all safety warnings before installation and use to prevent electric shock, fire hazards, or product damage.

  • Electrical Safety: Only suitable for indoor dry use. Do not use in humid, outdoor, or bathroom environments.
  • Power Limit: Do not use bulbs exceeding 60W. Exceeding this limit can lead to overheating, melting, and potential fire hazards.
  • Operation Notice: Do not touch the adapter or the bulb during operation, as they may become hot and cause burns.
  • Usage: Do not disassemble, squeeze, or modify the product artificially. Any such action may compromise safety and void the warranty.
  • Fire Prevention: Keep the adapter and connected bulb away from flammable items such as cloth, paper, and plastic.

3. Setup and Installation

Follow these steps carefully to install the lamp holder converter:

  1. Cut off Power: Before starting any installation, ensure the power supply to the lamp fixture is completely turned off at the circuit breaker or switch to prevent electric shock accidents.
  2. Install Adapter: Screw the E17 male thread end of the converter clockwise into the original E17 lamp holder firmly until it is secure.
  3. Install Bulb: Align and screw your E12 base bulb clockwise into the E12 female socket of the adapter until it is tight.
  4. Restore Power: Switch on the power supply to the fixture.
  5. Verify Operation: Check if the bulb lights normally.

Important: It is forbidden to use bulbs exceeding the maximum rated power of 60W.

E17 and E12 ends of the converter labeled
Figure 2: E17 Male Base and E12 Female Socket

This image provides a close-up view of two E17 to E12 lamp holder converters. One converter clearly shows the E17 male screw base, while the other displays the E12 female screw socket, with both ends explicitly labeled for easy identification.

4. Operating Instructions

Once installed, the E-SIMPO E17 to E12 converter operates by simply turning on the light fixture's power switch. Ensure that the bulb used is compatible with the E12 socket and does not exceed the 60W maximum power rating of the adapter. Always refer to the Safety Warnings section for safe operation practices.

5. Maintenance & Storage

5.1. Maintenance

  • Daily Cleaning: Cut off power and allow the adapter and bulb to cool down completely. Wipe the surface with a dry, soft cloth only. Do not use liquid cleaners.
  • Regular Inspection: Periodically check the adapter for any signs of cracks, aging, or poor contact. If any damage is observed, discontinue use immediately.

5.2. Storage

  • Storage Condition: Store the converter in a dry, cool, and dust-free place when not in use.
  • Protection: Avoid storing in conditions where it might be subjected to extrusion or collision, which could cause physical damage.

Replacement Tip: Stop using the adapter immediately if you notice cracking, a burning smell, or abnormal heating.

6. Troubleshooting

If you encounter issues with your E-SIMPO E17 to E12 converter, refer to the table below for possible causes and solutions:

Fault PhenomenonPossible CauseSolution
Bulb does not lightLoose installation or poor contactReinstall adapter and bulb tightly
Light flickeringOxidized thread and unstable contactClean contact surface and screw tightly again
Adapter overheatingExceeds rated power (60W)Replace with bulbs within the 60W power range

7. Specifications

7.1. Basic Product Information

ItemDetails
Product NameE17 to E12 Lamp Base Conversion Adapter
Main FunctionConvert E17 screw socket to E12 small screw lamp socket
MaterialHigh temperature flame retardant plastic (PBT) / Ceramic + Pure copper conductive parts
Compatible BulbE12 LED bulb, candle bulb, miniature decorative bulb
ApplicationCrystal lamp, chandelier, cabinet lamp, bedside lamp, indoor small decorative lighting
Product FeaturesHigh temperature resistant, flame retardant, safe insulation, easy installation, stable electric conduction
Usage EnvironmentIndoor dry environment only

7.2. Technical Specifications

ParameterSpecification
Input InterfaceE17 Male Screw Base
Output InterfaceE12 Female Screw Base
Rated VoltageAC 110V-240V
Rated Current≤2A
Maximum Bearing Power≤60W
Working Temperature-20°C ~ +160°C
Flame Retardant LevelV-0 Grade
Protection GradeIP20
Dimension diagram of E17 to E12 converter
Figure 3: Converter Dimensions

This technical drawing illustrates the dimensions of the E17 to E12 lamp holder converter. It shows the E17 base, an overall height of 21mm, and a diameter of 18mm for the E12 socket.

8. User Tips

  • Always ensure the power is off before installing or removing the adapter or bulb to prevent electrical hazards.
  • Double-check that your bulb's wattage does not exceed 60W to prevent overheating and ensure the longevity of the adapter and bulb.
  • For optimal performance and safety, use the adapter only in dry, indoor environments as specified.

9. Warranty & Support

9.1. Warranty

This product is covered by a quality warranty for manufacturing defects under normal installation and use. The warranty does not cover:

  • Damage caused by overload.
  • Damage due to improper installation.
  • Damage resulting from use in a humid environment.
  • Damage from private disassembly or modification of the product.

The manufacturer shall not be liable for personal injury or property loss caused by non-standard use of this product.

Product specifications and appearance are subject to actual products, and the manufacturer reserves the right to adjust parameters without prior notice.

9.2. Support

For further assistance or inquiries, please contact your seller or the manufacturer directly.

A detailed PDF manual is also available for download here.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.